Gsd5500go1ww Parts

This is a replacement washer drive motor that powers the tub to spin and agitate, restoring normal wash and spin cycles. Fits specified GE top-load washers and matches OEM form and function. What it does

• Spins the wash tub to perform spin cycles and remove water
• Powers the agitation/oscillation action during wash cycles
• Commonly replaced when the washer won't spin, won't agitate, or hums without turning
• Helps eliminate intermittent power-to-motor issues when motor failure is the root cause

• One replacement drive motor

• Disconnect power before starting any repair to avoid electric shock
• May require removing the washer cabinet or access panels and detaching the old motor wiring and mounting screws
• Handle carefully — support the tub/drum as needed during motor removal and reinstallation

This hose clamp secures a washer or dryer hose connection to help prevent leaks and keep hoses firmly attached during operation. It's a simple replacement for worn or loose hose fasteners. What it does:

• Holds inlet or drain hose to the appliance fitting to reduce slipping and leaks
• Restores a tight seal at hose connection points that may be leaking or wobbling
• Keeps hoses positioned correctly during fill and drain cycles
• Useful when clamp is rusted, stretched, or no longer grips reliably

• One hose clamp

• Disconnect power and turn off the water supply before replacing the clamp
• Slide clamp onto hose, position over the fitting, then compress or tighten per clamp type (use pliers or screwdriver as required)
• Inspect the hose and fitting; replace the hose if cracked or damaged
• Test for leaks after restoring power and water

A stainless steel hex-washer-head screw used to secure panels and components on compatible appliances. Corrosion-resistant construction helps maintain a secure fit where short, strong fasteners are required. What it does

• Fastens appliance panels, trim, or brackets where an 8-18 thread and short 3/8" length are specified
• Hex washer head provides a larger bearing surface to reduce pull-through
• Stainless finish resists rust in humid appliance areas
• Common replacement when original mounting screw is stripped, missing, or corroded

• One stainless steel hex-washer-head screw

• Use the correct 8-18 thread fastener and do not force mismatched screws to avoid thread damage
• Tighten securely but avoid overtightening to prevent stripped threads or cracked panels
• Power tools may be used with appropriate bit, but start by hand to ensure proper alignment
• If installing near electrical components, disconnect power before servicing

A 10-24 x 1/2 thread-forming screw used to fasten panels and small components in appliances. Replaces missing or damaged fasteners to restore secure mounting and reduce rattling or misalignment. What it does:

• Secures panels, brackets, or trim to prevent movement and vibration
• Replaces missing, stripped, or damaged screws that allow parts to loosen
• Helps maintain proper alignment of doors and access panels
• Small, general-purpose fastener for a variety of appliance interior and exterior attachments

• Disconnect power to the appliance before beginning any repair
• Use the correct driver bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent thread damage
• Compare the old screw to length and thread before installing

This is a stainless steel hex washer-head screw used to fasten and secure components. Its integrated washer head provides a broad bearing surface for a tight, durable hold in appliance assemblies.

• Secures panels, brackets, and hardware to prevent looseness and vibration
• Restores proper fastening when originals are stripped, missing, or corroded
• Stainless construction helps resist rust in moisture-prone areas
• Common symptoms of a needed replacement include rattling, loose panels, or missing hardware

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct nut driver or socket for the hex head to avoid stripping
• Replace any damaged or missing fasteners in matched pairs or sets for even clamping
• Do not overtighten; snug to manufacturer torque guidance when available

This switch interlock assembly secures the appliance door and completes the electrical circuit so the unit can start and run safely. Replacing a worn interlock restores reliable door sensing and helps ensure normal cycle operation. What it does:

• Detects and holds the door/lid closed so the appliance will start
• Completes the electrical pathway for motor and control circuits
• Prevents operation when the door is open or not fully latched
• Can stop mid-cycle or prevent starting when the interlock fails

• One switch interlock assembly

• Disconnect power (unplug or switch off the breaker) before replacing the part
• Handle mounting screws and wiring harness carefully; match connector orientation when reinstalling
• Verify door alignment and latch function before restoring power

Size: 8-32 x 5/8 inch.

A replacement knob latch handle that secures and indexes the appliance control knob for reliable selection and tactile feedback. Restores proper knob engagement to help prevent slipping or incomplete setting changes. What it does:

• Latches and holds the control knob in selected positions so settings stay engaged.
• Provides tactile detents for clear position feedback when turning the knob.
• Commonly replaces worn, cracked, or broken latch pieces that let the knob slip or fail to engage.
• Fits directly onto the control shaft and works with the existing knob assembly.

• Disconnect power (unplug or switch off circuit) before servicing to avoid shock or injury.
• Removal typically requires removing the control knob and/or console trim to access the latch; keep track of fasteners.
• Inspect the control shaft and surrounding components for wear; replace damaged knobs or retention clips as needed.

White. 8-18 x 5/16 inch.

This is a genuine replacement screw used to secure components and panels on compatible GE appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or internal components to maintain proper alignment
• Stops rattling or vibration caused by loose fasteners
• Replaces missing, stripped, or damaged screws to restore safe operation
• Helps maintain seals and clearances by holding parts firmly in place

• Screw

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to components
• Keep removed fasteners organized to ensure correct reassembly

This long front panel replaces a damaged or worn control-area panel to restore the range's appearance and provide a secure mounting surface for control components. It fits the long control area used on select GE ranges. What it does:

• Replaces cracked, dented or heavily scratched front/control-area panels to improve appearance
• Provides the mounting surface and alignment for control switches and trim
• Helps keep internal components shielded from spills and debris near the controls
• Restores a flush fit where the original panel was warped or bent

• Disconnect power to the appliance (unplug or switch off breaker) before starting work
• Remove control knobs and any trim pieces to access mounting screws; keep original fasteners for reassembly
• Handle the panel carefully to avoid cuts from sharp edges and to prevent cosmetic damage
• Take care when disconnecting and reconnecting wiring;

A stainless-steel #6-20 screw (1/2" length) used to fasten appliance panels and components securely. Durable corrosion-resistant finish helps maintain a tight fit and long-lasting hold in wet or humid areas. What it does:

• Fastens trim, brackets, panels, and internal components where a #6-20 x 1/2" screw is specified
• Provides a corrosion-resistant connection for areas exposed to moisture
• Restores loose or missing fasteners that cause rattling or misalignment
• Matches OEM thread and length for proper fit and function

• One stainless steel #6-20 x 1/2" screw

• Turn power off and unplug appliance before servicing
• Use the correct screwdriver or driver bit to avoid stripping the head
• Do not overtighten; stop when the component is snug and aligned
• Replace any additional damaged fasteners with matching OEM screws

A replacement clamp that secures hoses or wiring to keep lines routed and stable, helping prevent rubbing, leaks and noise. Restores a reliable hold for tubing and harnesses so the appliance runs quietly and safely. What it does:

• Holds hoses, tubing or wire harnesses in place to reduce movement and chafing.
• Helps prevent leaks and water line abrasion caused by loose fittings.
• Reduces rattling or vibration from unsecured lines or cables.
• Keeps routing organized so adjacent components aren't stressed or worn.

• Disconnect power before servicing the appliance; shut off water supply when working on water or drain lines.
• Remove the old clamp and position the replacement so it fully engages the hose or harness, avoiding twists.
• Use appropriate hand tools (pliers or screwdriver) and secure the clamp evenly; avoid overtightening.
• Inspect surrounding hoses and wiring for damage while installing; replace any components that show wear.