Gsh22jfre Parts

This freezer door gasket creates an airtight seal around the door to keep cold air in and moisture out. Replacing a worn seal helps restore stable temperatures, reduce frost and condensation, and improve overall efficiency. What it does:

• Seals the perimeter of the freezer door to prevent air leaks and humidity intrusion
• Helps maintain consistent internal temperature and energy performance
• Replaces gaskets that are torn, warped, brittle, or won't stay seated
• Common symptoms include excess frost or ice near the door, condensation around the frame, or the door not closing flush

• 1 freezer door gasket

• Disconnect power before servicing
• Warm the new gasket in hot water or with a low-heat hair dryer to improve flexibility
• Remove the old gasket and press the new gasket fully into the door channel, starting at the corners
• Close the door and check for an even seal (use a "dollar bill" test); allow up to 24 hours for the gasket to relax and conform

Front mounting grommet.

This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.

• Secures covers, brackets, and trim to the appliance cabinet or liner
• Replaces missing, stripped, or corroded hardware
• Helps reduce vibration noise and loose or misaligned parts
• Maintains proper fit of guards, kickplates, or internal panels

• Disconnect power; turn off water supply if working near water lines
• Match to the original fastener to size and thread
• Start threads by hand to avoid cross-threading; tighten snugly, not excessively
• If threading into plastic, avoid overtightening to prevent damage

This part is a lower tail handle. This is a genuine OEM part made by General Electric and has been sourced directly from the manufacturer. This part is intended to replace a broken or detached tail handle on multiple different models and brands of refrigerators. The tail handle fixes to the exterior of the refrigerator. A missing or broken tail handle can prevent the door from functioning properly. The tail handle can become detached from the appliance with regular use and may require replacement. Always ensure the appliance is disconnected from its power source before attempting any repairs. Take appropriate safety precautions and wear protective work gloves. Proper tools are needed to install this part. For more accurate installation information on how and where to install this replacement lower tail handle, refer to the original manufacturer diagrams or owner's manual.As an authentic replacement part, this lower tail handle is suitable for use on various models of refrigerators manufactured by General Electric and Hotpoint. Please note that this is a genuine part made of high-quality and durable plastic and is sold individually.

This is the glass insert for the refrigerator pan cover, creating the flat shelf above the drawers. Replacing cracked or missing glass restores a stable, easy-to-clean surface and helps contain spills from reaching the storage areas below.

• Forms the flat shelf that tops the pan cover assembly over crisper/deli drawers
• Provides a sturdy surface for storing food items
• Helps contain small spills so they don't drip into drawers below
• Replace if the glass is cracked, shattered, chipped, bowed, or missing

• Disconnect power and remove food from the affected shelf area
• Lift out the pan cover frame and slide out the old glass
• Clean the frame's channels; seat the new glass fully and evenly
• Handle glass carefully and wear cut-resistant gloves

This replacement freezer door gasket creates a secure, flexible seal around the freezer door to help keep cold air in and warm air out, restoring proper door closure and helping the freezer maintain consistent temperature. What it does:

• Forms an airtight seal around the freezer door to reduce air leaks.
• Helps prevent frost and ice buildup inside the freezer.
• Restores proper door closure so the freezer maintains temperature more reliably.
• Reduces excess compressor cycling associated with a worn or damaged seal.

• Disconnect power or turn the appliance off before starting to avoid electrical hazards.
• Remove the old gasket and clean the door flange and mounting channel before installing the new seal.
• Press the new gasket fully into the channel, working around the door to ensure even seating and full contact.
• If the gasket feels stiff, follow OEM guidance or warm it gently to help it flex; avoid high heat that can damage the seal.

This damper gasket seals the refrigerator air damper opening between the freezer and fresh food compartments to prevent air leaks and help maintain stable temperatures. A new seal supports proper airflow and helps reduce moisture or frost near the damper. What it does:

• Seals the perimeter of the air damper/baffle to prevent bypass air leaks
• Helps regulate airflow from freezer to refrigerator for consistent cooling
• Wear, flattening, or tears can lead to warm spots in the fresh food section
• May also contribute to condensation, frost, or whistling/draft at the damper cover

• 1 damper gasket

• Unplug the refrigerator before servicing
• Remove the interior damper cover/grille to access the damper; note gasket orientation
• Seat the new gasket evenly around the damper frame without stretching or twisting
• Reinstall cover, restore power, and verify airflow and door sealing

This ice dispenser funnel guides cubes or crushed ice from the door chute into your glass. Replacing a cracked or missing funnel restores clean, targeted dispensing and helps reduce stray ice around the dispenser area.

• Directs ice from the chute into the cup to minimize spills and scatter
• Common symptoms: cracked or broken funnel, ice missing the glass, jamming at the outlet, loose/misaligned funnel
• Bisque finish to match bisque dispenser trim on compatible units
• Durable molded plastic designed for the dispenser recess

• Disconnect power to the refrigerator before servicing the dispenser area
• Carefully remove the dispenser trim/control panel; support any wiring harnesses
• Release tabs or screws holding the old funnel, note orientation, and transfer any existing hardware if needed
• Reassemble, restore power, and test both cubed and crushed ice for proper alignment

Includes 12 retainer rings.

Replacement diverter overflow that helps channel excess water away from the ice maker/water system to reduce pooling and leaks. Restores proper drainage so the refrigerator interior stays dry and operates as intended. What it does:

• Directs overflow or stray water from the ice maker/water area into the drain path
• Helps prevent water pooling or dripping inside the freezer or cabinet
• Use when you notice leaks, water pooling under shelves, or water coming from the dispenser/ice area

• Always disconnect power and shut off the water supply before starting any repair
• Removal of interior shelves/trim or access panels may be required to reach the diverter
• Handle plastic tabs and clips carefully to avoid breakage; replace any damaged fasteners

This cable clamp secures refrigerator wiring to the cabinet, keeping harnesses organized and protected. Replacing a missing or damaged clamp helps prevent chafing and vibration noise while maintaining proper clearance from fans and other moving components.

• Anchors wire harnesses in their designed routing
• Helps prevent insulation wear from rubbing or vibration
• Keeps wires clear of sharp edges and moving parts
• Common signs it's needed: missing/broken clamp, loose or dangling wires, or new rattling/buzzing noises

• Disconnect power before servicing
• Access the clamp location and note original wire routing
• Position the clamp and secure with the existing fastener; do not overtighten
• Ensure wires aren't pinched and have clearance from the fan/compressor before restoring power

This solenoid saddle is a small mounting bracket that secures a refrigerator solenoid in the correct position. By preventing movement and misalignment, it helps the linked mechanism engage smoothly and consistently.

• Secures the solenoid to its housing or frame to prevent shifting
• Maintains proper alignment for reliable actuation
• A worn or broken saddle can cause buzzing/chattering and intermittent operation
• Restores stable mounting to help the connected mechanism work correctly

• Disconnect power; shut off water supply if working near water lines
• Access the solenoid assembly and note the original saddle's orientation
• Transfer the solenoid into the new saddle and reuse existing fasteners/clips
• Smooth operation before reassembling panels

Specs: 8-18 AB IHW 5/8 S

This 10-18 Hi/Lo hex-washer screw is a direct-use replacement fastener for appliance panels, brackets and components. It restores secure mounting and helps stop loose trim, rattling or parts that shift during use. What it does:

• Secures panels, trim pieces, mounting brackets and similar components that use a 10-18 thread with a hex-washer head
• Restores proper fit where screws are missing, stripped, or corroded
• Helps eliminate rattling, vibration noise, and misaligned parts caused by loose fasteners
• Matches OEM head and thread style for a correct mechanical fit in specified locations

• Turn power or gas to the appliance off before working on electrical or gas-equipped units; unplug when applicable
• Use the correct sized hex driver or socket to avoid rounding the head
• Tighten until snug—do not overtighten to avoid stripping threads or damaging thin sheet metal
• If replacing multiple fasteners in a load-bearing area, replace all to ensure even fit and alignment

This condenser fan mounting bracket secures the condenser fan motor and blade in the correct position to move air across the coils. Replacing a cracked or bent bracket restores stable mounting, reduces vibration, and helps maintain proper condenser airflow.

• Holds the condenser fan motor/blade assembly in alignment for proper airflow through the condenser
• Maintains clearance to prevent the fan blade from rubbing or contacting nearby components
• Helps reduce rattling, vibration, or scraping noises from the rear of the refrigerator
• Damage or misalignment can contribute to restricted condenser airflow and warmer temperatures

• Disconnect power and pull the refrigerator away from the wall to access the rear service area
• Remove the rear lower access panel; note wiring and hardware locations
• Support the fan motor/blade while removing the old bracket; transfer motor, blade, grommets, and screws to the new bracket
• The fan spins freely with proper clearance and correct airflow direction before reassembly

Size: 10-16 ab.