Gsh25jfta Bb Parts

Phillips pan head screw for refrigerators. Secures trim panels, brackets, and internal components. Replace stripped, missing, or corroded fasteners.

This plug-in SCR is a solid-state replacement that controls electrical power to appliance circuits, restoring reliable on/off control and helping eliminate intermittent operation. It's a direct-fit replacement when the original SCR fails. What it does

• Regulates current flow in the control circuit to switch power to motors or heating loads.
• Stops erratic cycling or loss of power caused by a failed control semiconductor.
• Helps restore consistent operation when an appliance has intermittent start, no heat, or no motor run.
• Provides a rugged, compact replacement with a 5/16" connection style.

• One plug-in SCR

• Disconnect power to the appliance before accessing or replacing the SCR.
• Remove the appliance's control or access panel to reach the control board; note wire locations before unplugging.
• Plug the new SCR into the original connector or replace per the service manual.
• Verify correct operation after installation and reassemble all panels before restoring power.

Metal retainer spring secures trim panels and lightweight components in your refrigerator. Replace when worn, broken, or missing to restore snug fit.

This boot auger motor drives the auger inside the ice dispenser boot to move ice from the bin to the dispenser chute. Replaces a failed motor to restore normal ice dispensing and reduce jams. What it does:

• Rotates the auger inside the dispenser boot to push ice forward for dispensing
• Helps prevent ice buildup by moving packed cubes during dispense cycles
• Stops working when motor windings or gears fail, causing no ice to dispense or intermittent dispensing
• Works with the dispenser drive and auger assembly to transfer ice from the bin to the chute

• One boot auger motor

• Disconnect power to the appliance before starting any repair
• Access typically requires removing the freezer/refrigerator door trim and dispenser housing; follow OEM service instructions
• Inspect related components (auger, coupler, wiring) and replace if damaged

Basket support slide for refrigerator door or interior shelves. Replace if cracked, broken, or missing to restore proper basket support and alignment.

Replacement end cap for refrigerator door handles. Covers and secures the exposed handle end for a finished look. Replace if cracked, broken, or missing.

White lower front grille base assembly for refrigerators. Replaces cracked, broken, or missing trim panel to restore a clean, finished appearance.

This is a 10-24 x 1.0 inch screw used to secure appliance panels and components. It replaces worn or missing fasteners to restore proper fit and reduce rattling or loose parts for safer, quieter operation. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable
• Stops vibrating or rattling caused by loose or missing screws
• Restores proper grounding/attachment where a threaded fastener is required
• Matches OEM thread size and length for a correct fit when replacing damaged screws

• Use the correct driver bit and turn carefully to avoid stripping the head or threads
• Do not overtighten; snug until secure to prevent damage to mating parts
• Replace like-for-like with the same thread size and length for proper fit
• Disconnect power and follow appliance safety guidelines before accessing internal components

Hex washer head screw secures panels, brackets, and small assemblies inside refrigerators and ranges. Replace stripped, missing, or damaged screws.

Mullion air duct for side-by-side refrigerators. Directs cold air between freezer and fresh food sections. Replace if cracked, broken, or damaged.

White plastic door stop plate installs on refrigerator cabinet to support door closure. Replace if cracked, broken, or missing to restore proper fit.

Bottom adjustable hinge pin for refrigerator doors. Installs at the lower hinge to level and align doors. Replace if worn, stripped, or doors won't stay level.

Secures glass shelves in place to keep food organized and prevent sagging. Replaces cracked, broken, or worn brackets that no longer hold shelves level.

Secures the evaporator fan motor to the freezer evaporator assembly. Replace if cracked, broken, or causing motor vibration and noise issues.