Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
White hinge cover cap for side-by-side refrigerators. Replaces cracked, broken, or missing hinge covers to restore a clean, finished appearance.
Bisque plastic trim cover that snaps over the refrigerator door hinge. Replace if cracked, broken, or missing to restore a clean appearance.
Found the parts on this website and installed them. I was actually quite happy since there is a diagram of the door and I could go piece-by-piece to order what I needed. Read more
Seals freezer air duct to maintain proper temperature and airflow. Replace if frost builds up or cold air leaks. Verify fit with your model number.
Replacement pivot that supports and aligns refrigerator doors or drawers. Needed when original pivot is cracked, broken, or worn, causing misalignment.
When we inspected the first time we found that Plactic had broken from the spiral part that for wards the ice. Also there were cracks in two places of other parts. There was a hole in the bottom of the bin. The new spiral was assembled and two new parts were replaced with help from the video and the diagram and the unit worked well. Two months later, ice maker would not forward any ice though the bin was full. We emptied the bin sand have ordered a new part or two in hopes that they will... Read more
Closes and protects the end of your refrigerator's mullion air duct on the door jamb. Replace this cap if cracked, broken, or missing to maintain a finished appearance.
Installed new stainless steel pan replacing broken original plastic pan and installed new rubber grommets for the compressor Read more
Replacement 8-18 x 3/4 inch pan/hex head screw for securing refrigerator panels, trim pieces, and brackets. Restores proper fastening for loose parts.
Ice not crushing or dispensing properly? This refrigerator ice crusher auger blade assembly moves ice through the dispenser. Common DIY fix.
White
This 10-32 hex washer screw secures panels and components in appliances, providing a reliable fastener that helps keep parts aligned and vibration-free during operation. Designed for a snug fit in threaded appliance mounting holes. What it does:
Fridge warm but freezer cold? Frost buildup on evaporator coils means a failed defrost heater. This assembly prevents ice blockage, restoring airflow.
I unplugged the fridge and took all the food and shelving out of the freezer and then proceeded to take off the bottom sliding drawer rack on both sides off (4 Phillips head screws). Then took off the light bulb cover and then the light bulb. Then the back wall that covers the coils and tubes that the refrigerant runs through ( 2 screws with hex head). After sliding out the back wall I could see that the entire coil area was frosted and iced up. I took a blow dryer and melted all of it over... Read more
Usually ships within 4 - 14 days
Damaged or cracked dispenser trim? This trim snaps around your refrigerator's water and ice dispenser opening for a finished look. DIY repair in 20 minutes.
After viewing your video the job went as planned and took maybe 20 minutes. Read more
This small guide sits at the icemaker fill area and manages the water stream. It directs incoming water into the fill cup and channels any excess safely away to help prevent splashing, leaks, and ice buildup inside the freezer.
The diverter was broken and looked like housing also, so replaced both and now works fine Read more
Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.
Seals the air damper opening between freezer and fresh food compartments to prevent air leaks and maintain stable temperatures. Replace if worn or cracked.
Evaporator fan motor in our freezer was bad. Ordered new one with 2 day delivery and had it in 2 days. Thankfully it was very easy to get to from the front of the freezer. There are 3 different options for same motor with different wire harnesses. I bought the cheapest option and then snipped and reconnected the wires to the existing harness. That saved us $50. Still well under an hour from the time I opened the tool box to putting the last tool away. Fridge is now plenty cold even set on 5. . Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.