Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Refrigerator not cooling or running constantly? This compressor powers your cooling system. Advanced repair, allow 2-4 hours for replacement.
Lower gasket shield protects your refrigerator door seal from wear and damage. Replace if cracked, bent, or the door isn't sealing properly. Confirm fit.
Both items were OEM replacements, reasonably priced, and were shipped/arrived quickly. Replaced both in five minutes. Read more
Refrigerator not cooling but freezer works? This air damper and thermistor assembly controls airflow between compartments. Restores proper cooling.
Replaced all temperature sensors, damper, and the thermistor (all probably were not needed but I was not exactly sure the issue, but I knew my heater, compressor, and the evaporator fan were all working correctly). Read more
Front mounting grommet for refrigerator ice makers. Secures ice maker assembly to freezer wall. Replace if cracked, missing, or worn to restore stability.
Replaced the housing the water filter screws into. Water works fine now. Read more
Size: 8-18 AB TSQ 5/8 SS
I replaced the upper and mid spray arms and bearings, removed filters and screens and cleaned everything. Pulled pump and replaced the connector and the collection sump. Repair took about 3 hours and went very smoothly thanks to the AppliancePros video! I'm on the east coast so I could not believe it when the parts arrived less than 24 hours after I placed the order! Prices were great too . . . I'm a customer for life and my dishwasher cleans the dishes like new now! Read more
Size: 10-32 GXTT FLP.595 S
Great site to DIY! Purchased fresh produce drawer railing and parts. Fixed in under 10 minutes. Thanks so much! Read more
Mounting screw fastens panels, brackets, and trim in refrigerators, dishwashers, and ranges. Replace missing, stripped, or rusty screws to secure parts.
New parts. Read more
Ice cubes jamming or not dispensing? The stripper comb releases cubes from the ejector fingers during harvest. Moderate DIY, requires partial disassembly.
I am a retired commercial hvac professional so I know how icemakers work but don't know all the brands. Looked at 15 videos on general ice makers on the internet to get clues, and then I made a list of things I wanted: brand new solenoid fill valve, new cardboard backing for the rear that the delivery men broke up delivering the fridge, and a new plastic stripper plate because outboard tine was broken on mine. Next I changed my whole house water filter. (Don't want trash in lines) Then I... Read more
This OEM part is a refrigerator dispenser interface. The dispenser interface is responsible for the main functions of the refrigerator, such as adjusting the temperature settings as well as the other functions that are displayed on the interface. If the refrigerator is no longer cooling efficiently, failing to maintain temperature, dispensing water, or the touchpad is unresponsive, the interface might need to be replaced. Thankfully, replacing this part is not a difficult process.To replace the old interface, make sure that all power to the refrigerator is turned off. Open the refrigerator door and remove the door panel of the interior of the refrigerator. Locate the old control board and remove the wire harnesses that connect to it. Take note of the wire connector's orientation and reinsert the wires to the new board. Snap the new interface back in place and reinstall the inner panel. This genuine replacement part is sold individually and is compatible with General Electric, Hotpoint, and RCA brand refrigerators.
Put in a new interface. Read more
Cushions where the washer lid meets the top panel to soften closure and protect the finish. Replace worn, cracked, or missing bumpers to reduce noise.
The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more
Includes 12 retainer rings.
I ordered a replacement auger from AppliancePartsPros.com. Upon receipt of the new auger, I watched the repair video and took the ice crusher apart. I found several other parts that needed to be replaced as well. Once All the parts were received, I again watched the video. The video was not specific enough to show how to reassemble the ice crusher blades and the two types of washers. I found another video on YouTube that walked me through specific details of assembly and everything went... Read more
Secures the refrigerator handle to the door. Replace this fastener if it's missing, stripped, or damaged to eliminate handle wobble and restore alignment.
Seals the air damper opening between freezer and fresh food compartments to prevent air leaks and maintain stable temperatures. Replace if worn or cracked.
Evaporator fan motor in our freezer was bad. Ordered new one with 2 day delivery and had it in 2 days. Thankfully it was very easy to get to from the front of the freezer. There are 3 different options for same motor with different wire harnesses. I bought the cheapest option and then snipped and reconnected the wires to the existing harness. That saved us $50. Still well under an hour from the time I opened the tool box to putting the last tool away. Fridge is now plenty cold even set on 5. . Read more
Replacement diverter overflow that helps channel excess water away from the ice maker/water system to reduce pooling and leaks. Restores proper drainage so the refrigerator interior stays dry and operates as intended. What it does:
Plastic retaining clip that secures drawer divider modules in place. Replaces broken, cracked, or missing snuggers to restore proper fit and separation.
Bought two replacement pieces (one as a spare), and snapped it into place. Read more
Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.