Gss23wgta Parts

This light shield protects and directs the interior lamp in the refrigerator fresh-food compartment, keeping the bulb covered and preventing direct contact while improving light distribution for easier viewing. What it does:

• Covers the interior lamp to prevent bare-bulb contact and protect food from accidental breakage
• Helps diffuse and direct light for more even illumination inside the fresh-food compartment
• Replaces cracked, yellowed, or missing shields that cause glare or reduced light output
• Fits behind the fresh-food compartment light assembly to maintain proper lamp placement

• Disconnect power to the refrigerator before servicing to avoid electrical shock
• Remove the existing shield carefully; avoid forcing plastic clips to prevent breakage
• Align tabs/clips and snap the replacement shield into place until fully seated

Fresh food side. Color: white. For the same part in black, purchase WR02X10779.

This replacement screw secures refrigerator panels, brackets, and trim to help keep components aligned and quiet. It matches the specified #8-18 thread and 1-1/2 inch length used at designated mounting points.

• Fastens panels, brackets, covers, and hardware as designed by the manufacturer
• Restores a missing or damaged fastener to keep parts secure and aligned
• Correct #8-18 tapping thread and 1-1/2 in. length for specified locations

• Unplug the refrigerator or disconnect power before servicing
• Wear cut-resistant gloves to protect from sharp edges
• Start the screw by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse any model-specific washers or clips originally installed on your unit

This condenser assembly is the condenser coil used in compatible refrigerators to release heat from the refrigerant so the appliance can cool efficiently. Replacing a damaged coil helps restore proper cooling performance and energy use. What it does:

• Circulates refrigerant through the condenser coil to dissipate heat from the refrigeration system
• Supports normal compressor cycling and helps maintain steady internal temperatures
• Common symptom fixes: reduces long run times, improves inadequate or uneven cooling, and addresses overheating or noisy compressor operation
• Works with the condenser fan and other sealed-system components to complete the heat-exchange process

• Disconnect power to the refrigerator before servicing to avoid electric shock
• Access commonly from the rear lower panel or front grille; may require removal of kick plate or back cover
• Avoid damaging the coil fins; handle carefully and use fin comb if needed

This stand off is a small mounting spacer that secures and spaces internal components, restoring proper alignment and reducing panel movement or vibration for quieter, more reliable operation. What it does:

• Provides a solid mounting point to hold panels, brackets or wiring harnesses in place.
• Replaces broken, cracked or missing standoffs that allow components to shift or rub.
• Helps stop rattling, buzzing or misalignment caused by loose mounting points.
• Keeps proper clearance between parts to prevent wear or chafing over time.

• Disconnect power to the appliance before starting any repair.
• Remove the affected panel or access cover to reach the damaged standoff.
• Replace the old standoff with the new part; retain and reuse any existing screws or fasteners unless damaged.
• Hand-tighten mounting hardware and test the appliance; avoid overtightening plastic standoffs.

This replacement cover hinge secures and pivots the appliance cover so the lid or top opens and closes smoothly. Restores proper alignment and support for safe, reliable operation. What it does:

• Provides a durable pivot point for the appliance cover or lid
• Replaces worn, cracked, or broken hinge that causes sagging or misalignment
• Helps eliminate rubbing, catching, or noisy operation when opening/closing
• Restores proper fit to prevent gaps and improve safety when the cover is closed

• One cover hinge

• Disconnect power before servicing
• Support the cover or lid while removing fasteners to prevent it from falling
• Use appropriate hand tools; retain original fasteners unless replacement hardware is supplied
• After installation, verify smooth operation and secure mounting before returning appliance to service

This spacer is a small mounting support used to maintain proper clearance and alignment between refrigerator panels, doors, or components. It helps reduce rubbing, vibration, and noise by restoring correct spacing and fit. What it does:

• Keeps panels, trim, or components spaced correctly to prevent metal-on-metal contact and wear
• Helps align doors and panels for a flush fit and smoother operation
• Reduces vibration and rattling caused by misaligned parts
• Used wherever a fixed clearance or gap is required during reassembly

• Disconnect power to the appliance before beginning any service that requires panel or component removal
• Inspect mating surfaces for damage or debris before installing the spacer; replace any damaged fasteners
• Install in the same orientation and location as the original spacer; do not overtighten mounting hardware

This foam insulation tube slips over refrigerator tubing to help reduce condensation and protect lines from moisture and minor abrasion. It's a simple replacement that restores padding and prevents dripping in affected areas. What it does:

• Insulates exposed tubing to reduce surface condensation and water buildup
• Cushions lines to help prevent chafing and minor damage
• Helps maintain a dry cabinet area by limiting drips from sweating lines
• Useful when original insulation is torn, compressed, or missing

• Disconnect power to the appliance before servicing; follow all safety guidelines
• Slide the foam sleeve over the tubing; trim to fit with a sharp blade if necessary
• Replace any damaged or brittle tubing discovered during install
• Do not use if foam is melted, charred, or contaminated

Evaporator cover gasket creates a moisture- and air-sealing barrier between the evaporator cover and freezer liner to help reduce frost buildup and improve cooling consistency. Replacing a worn gasket helps prevent ice accumulation and water leaks. What it does:

• Seals the evaporator cover to minimize moisture intrusion and air leakage into the evaporator area.
• Helps reduce frost and ice buildup on the evaporator and freezer walls.
• Can help address symptoms such as excess frost, water pooling in the freezer, or uneven/freezer temperatures.
• Restores proper evaporator cover fit for more consistent defrost performance.

• Disconnect power to the appliance before servicing to avoid shock or injury.
• Remove the evaporator cover per your model's service instructions, remove the old gasket, and clean the mating surfaces before installing the new gasket.
• Seat the gasket fully around the cover; some models use clips or adhesive.
• After reassembly and power-up, monitor the freezer for proper sealing, frost control, and any signs of leaks.

This grill base is the lower grille support for your refrigerator that restores proper grille alignment and appearance. It helps secure the toe-kick area and maintains correct airflow under the cabinet base. What it does:

• Replaces a cracked, broken, or warped lower grille support that lets the grille sit unevenly
• Restores secure attachment of the toe-kick/grille so it doesn't rattle or fall out
• Helps maintain proper clearance and airflow at the refrigerator base
• Improves finished appearance of the appliance front when the original base is damaged

• Disconnect power to the appliance before accessing the base area
• Remove the existing lower grille or toe-kick per the appliance service guide to access mounting points
• Typically fastens with clips or screws—retain hardware if reusable and align carefully during installation

Size: 8-32 t. Includes 12 screws.

This black cover hinge replaces a damaged or worn hinge cover to restore proper fit and appearance where the hinge mounts. It helps protect the hinge area and keeps the lid or top closing and opening smoothly. What it does:

• Covers and secures the hinge area to prevent wear and reduce rubbing or noise
• Helps keep the lid/top aligned for smooth opening and closing
• Restores finished appearance where the original hinge cover is cracked or missing
• Commonly used when the hinge cover is broken, loose, or causes wobble or misalignment

• Disconnect power to the appliance before servicing to avoid shock or injury
• Basic hand tools (screwdriver, socket) are typically required; keep removed fasteners for reinstallation
• Handle sharp edges carefully and support the lid/top during removal and installation

This is a replacement 8-18 x 9/16 machine screw used to secure internal and external appliance components. It restores proper fastening and helps stop rattling or loose panels caused by worn or missing fasteners. What it does

• Secures panels, brackets, or small assemblies to prevent movement and vibration
• Replaces stripped, corroded, or missing screws that can cause rattling or misalignment
• Helps maintain electrical and mechanical connections by holding parts in proper position
• Appropriate where an 8-18 thread size and 9/16" length are required

• Replacement screw

• Disconnect power to the appliance before accessing internal components
• Use the correct driver to avoid stripping the screw head and ensure proper torque
• Do not overtighten; snug until secure to avoid damaging threads or parts

This grill base is the lower kick grille assembly that supports and protects the appliance's lower front opening while keeping the unit's appearance finished. It restores proper airflow and a secure lower trim. What it does

• Replaces a cracked, bent or missing lower kick grille that can catch debris or look damaged.
• Helps maintain proper front trim alignment and keeps the space below the appliance covered.
• Reduces draft and prevents small objects from entering the area beneath the appliance.
• Restores original fit and appearance when the existing grill is loose or warped.

• Disconnect power to the appliance before beginning work.
• Typically fastens with a few screws or retention clips; use basic hand tools.
• Support the grille during removal to avoid scratching the finish or damaging adjacent trim.

This replacement pan-head screw is used in refrigerators to fasten panels, brackets, and covers so they stay tight and properly aligned. Replace a missing or damaged screw to restore a solid, rattle-free fit.

• Secures interior/exterior panels, brackets, trim, and covers
• Replaces missing, stripped, or corroded hardware
• Helps maintain proper alignment of attached components

• Disconnect power before servicing; shut off water if working near water lines
• Match location to the original fastener and start threads by hand to avoid cross-threading
• Do not overtighten, especially into plastic or thin sheet metal

• Thread size: #8-18 (type AB)
• Length: 1/2 inch
• Head style: Pan head, Phillips drive

This bottom door hinge secures the refrigerator/freezer door at the lower pivot and helps ensure smooth, stable opening and closing. Durable replacement that restores proper door alignment and keeps the seal functioning. What it does:

• Supports the bottom of the door and serves as the lower pivot point
• Keeps the door aligned so it closes fully and maintains a proper seal
• Reduces door sag, rubbing, or uneven gaps that cause cooling issues
• Fits and functions as the factory replacement hinge for compatible GE units

• Disconnect power to the appliance before beginning any repair
• Support the door while removing and installing the hinge to prevent injury or damage
• Use appropriate hand tools; avoid overtightening fasteners which can misalign the door