Gss25 Parts

RFID board that reads the filter's RFID chip and communicates with the refrigerator control to manage filter status and water dispensing. Replacing a failed board restores proper filter recognition and allows dispensing when a valid filter is installed.

• Reads/authenticates RFID-enabled water filters and reports status to the main control
• Enables or disables water dispensing based on filter presence/validity
• Supports filter-life tracking and "replace filter" indications on the display
• Failure symptoms include "filter not detected," replace light won't reset, or no water dispense after a filter change

• Disconnect power before service; shut off water if working around the filter/housing
• Access the board near the filter area; note connector orientation; transfer any mounting clips/covers as needed
• Handle electronics by the edges and use ESD precautions
• Restore power, install a compatible RFID-enabled filter, and dispense water to confirm recognition and flow

The lower gasket shield is a guide that protects the refrigerator door gasket at the bottom edge, helping the door close smoothly and maintain an even, reliable seal to keep temperatures stable and moisture down. What it does:

• Protects the lower edge of the door gasket from wear and deformation
• Guides the gasket into place for a snug, even seal
• Helps reduce warm-air leaks that can cause condensation or frost
• Replaces cracked, missing, or warped shields that can lead to poor sealing

• Includes 1 lower gasket shield

• Disconnect power and open the door for safe access
• Remove any lower door bins if needed
• Gently pull back the gasket at the lower edge to expose the shield and fasteners
• Install the new shield, reseat the gasket fully, and verify the seal with a paper-slip test

This foam insulation wraps the refrigerator's water reservoir to reduce sweating and help prevent freezing, keeping dispenser flow consistent and the fresh food compartment dry. Replace if the original insulation is torn, crushed, or missing. What it does:

• Insulates the water reservoir to help maintain a stable temperature
• Helps prevent the reservoir from freezing, which can slow or stop dispenser flow
• Reduces condensation that can drip or puddle inside the refrigerator
• Restores proper cushioning and protection around the tank

• 1 foam insulation piece for the water tank

• Unplug the refrigerator and shut off the water supply before servicing
• Remove shelves/drawers to access the water reservoir area
• Carefully remove the old insulation; avoid stressing or puncturing the reservoir and tubing
• Fit the new foam snugly around the tank, reassemble, restore power/water, and check for leaks and dispenser flow

This compressor overload protects the refrigerator's compressor by interrupting power when it overheats or draws excessive current. Replacing a weak or failed overload can stop repeated click/no-start symptoms and help restore normal cooling performance.

• Opens the circuit to protect the compressor during overheat or over-current conditions
• Automatically resets after cooling to prevent sustained damage
• Symptoms include: compressor won't start, rapid clicking from the compressor area, starts then stops, and a warm refrigerator/freezer
• Helps prevent motor and wiring damage caused by repeated overload events

• Disconnect power before servicing; wear appropriate PPE
• Access the rear machine compartment and remove the compressor/start device cover
• Note wire positions; pull the old overload straight off the compressor terminal and push the new one on fully seated; reconnect wiring and covers
• If the overload trips again after replacement, further diagnosis of the start relay, run capacitor, or compressor may be required

This is the refrigerator's user interface control panel assembly in white. It houses the touch controls and display you use to set temperatures and operate features like ice, water, and lighting on select 22–25 cu. ft. models.

• Provides the front control surface for temperature settings and dispenser functions
• Faulty UI can cause unresponsive or intermittent buttons, blank or dim display, or dispenser controls not working
• May help when features toggle on/off by themselves or settings won't change
• Cosmetic match: white finish (WW)

• Disconnect power before servicing to avoid electric shock
• Handle ribbon cables and connectors carefully to prevent damage
• Transfer any protective films or gaskets if present and route wiring as original
• After installation, restore power and verify all buttons and display functions

This is a screw intended for use in refrigerators, specifically as the top mounting screw for the handle. If the screw in the handle is missing, stripped, or otherwise not performing its function, a replacement screw should be ordered.A visual inspection will determine if a screw is missing. If the door handle is loose or falling off from the top, it is a sign that a replacement screw is required. This repair is a quick and easy process. It involves the use of a screwdriver. Remove the old screw if there is one in place. Line up the holes on the door and the door handle component before twisting the new screw into position. Wear gloves to protect hands during the repair.This screw is a genuine OEM replacement part. It is sourced directly from the manufacturer. The screw is sold individually. The screw is compatible with several different models of refrigerators. It can be installed in ranges made by Electrolux, Frigidaire, Gibson, Westinghouse, and Kelvinator.

Includes 12 washers.

A small metal retainer spring that secures trim and lightweight components so panels and shelves stay aligned and do not rattle. Replaces a worn or broken spring to restore a snug, reliable fit. What it does

• Holds trim, panels or lightweight components in position to prevent sagging or separation
• Stops rattling and vibration caused by loose parts
• Restores correct alignment of removable trim or small assemblies
• Helps maintain proper component engagement during normal use

• One retainer spring

• Disconnect power (unplug or switch off circuit) before working on appliances
• Use basic hand tools; access may require removing adjacent trim or clips
• Handle spring and surrounding trim carefully to avoid scratches or damage
• Replace damaged or missing mounting hardware before reassembly