Gtd280w Parts

Fix a dryer duct trap that won't open smoothly or rattles with replacement trap slides. Restores proper vent access and eliminates binding issues.

Dryer won't start or cycles won't select? This rotary switch translates knob rotation into control signals. Fixes unresponsive or erratic cycle selection.

Dryer won't change cycles or select settings? The rotary selector switch controls cycle options. Moderate DIY repair accessed from rear console panel.

This is the complete front-loading door assembly for a dryer, including the outer panel, inner panel, and glass or window. It provides the sealed closure needed to contain heat and tumbling laundry during the drying cycle. Replace this assembly if the door glass is cracked, the door frame is warped or damaged, or if the dryer will not stay closed or seal properly.

Fix a dryer that won't heat or cycles but doesn't ignite with this gas burner assembly. Restores consistent flame when the original is corroded or clogged.

If your dryer won't start, buttons are unresponsive, or the display is blank, the control panel may need replacement. Moderate DIY repair with basic tools.

Routes hot air from blower to external vent. Replace if cracked or leaking to restore airflow and prevent lint buildup. Confirm fit with model.

Dryer not heating? This gas valve and burner assembly controls gas flow and ignition. Moderate repair for restoring heat to your gas dryer.

Replaces the control panel buzzer that produces audible beeps and alerts. Needed when the existing buzzer is cracked, broken, or no longer chiming properly.

Genuine mounting screw that secures dryer panels, brackets, and trim pieces to the frame. Replace when stripped, missing, or worn to restore proper fit.

Fixes no steam or weak steam in dryers. This valve and pipe assembly regulates water flow to the steam system, resolving leaks at rear connections.

This hex washer-head screw secures dishwasher components like brackets, shields, and panels. Replacing a stripped or missing screw restores a tight fit and helps prevent vibration, rattling, and loose parts during operation.

• Fastens parts where a #10-16 x 1/2-inch hex washer-head screw is specified
• Secures brackets, panels, and assemblies to the tub or frame
• Helps resolve symptoms like loose panels, vibration, or rattling noises
• Restores proper hold when the original screw is stripped, missing, or damaged

• Disconnect power and shut off water to the dishwasher before servicing
• Match length and thread to the original; replace screws one at a time to maintain alignment
• Start threading by hand to avoid cross-threading; tighten snugly—do not overtighten, especially into plastic
• Verify no wires or hoses are pinched before reassembly

• Size: #10-16 x 1/2 inch
• Head: hex washer-head
• Type: AB tapping screw

These moisture sensor rods detect how damp the load is and signal the control, helping the dryer stop at the right time. Replacing worn or coated rods restores accurate Auto Dry performance and reduces damp loads or overdrying.

• Measures moisture by sensing conductivity across the rods as clothes tumble
• Sends feedback to the timer/control to adjust cycle length on Sensor/Auto Dry
• Safe symptom matches: cycles end too soon or run too long, clothes remain damp, Auto Dry doesn't advance reliably
• Residue from dryer sheets/fabric softener can insulate the rods and affect readings

• Disconnect power (and shut off gas supply for gas models) before servicing
• Access the rods at the front bulkhead/lint filter housing; panel removal may be required on some models
• Remove mounting fasteners, transfer wiring in the same orientation, and secure the new rods
• Ensure the sensing surfaces are clean and unobstructed; test on an Auto Dry cycle

Dryer won't heat or flame is weak or uneven? This valve and burner assembly regulates gas flow for consistent ignition and steady heating in your dryer.

Fix a dryer that won't start, makes grinding noises, or stops mid-cycle. This motor and blower assembly restores airflow and drum rotation. Advanced repair.

The Trap Duct Assembly is an OEM replacement part for GE dryers. This assembly provides the ducting and pathway to direct lint from the dryer drum to the lint trap. It plays a crucial role in efficiently removing lint and preventing blockages. 

Causes of a bad trap duct assembly can include cracks or breaks in the ducting material, crushing or collapsing of the duct, or loose connections that allow lint to bypass the trap. 

Symptoms of a bad trap duct assembly include:

• Increased drying times as lint is not properly exhausted 
• Lint building up inside the dryer instead of collecting in the trap
• Vibrating or rattling noises from loose or damaged ducting
• Reduced airflow leading to inefficient drying performance

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore models. Replace yours today for optimal lint removal and dryer operation.