Gtd45gasjws Parts

This strike plate mounts at the door opening and works with the door latch/strike to keep the appliance door securely closed during operation. Replacing a worn plate helps restore positive latching and reliable cycle start/stop via the door switch.

• Provides the catch surface for the door latch/strike to engage
• Helps keep the door closed and properly aligned
• Enables the door switch to engage so the cycle can run
• Common symptoms include: door won't stay closed, door pops open, unit won't start unless the door is pressed, visible wear or bending on the plate

• Disconnect power before servicing
• Open the door and remove the screws securing the existing plate
• Align the new plate with the latch/strike and fasten securely with the existing hardware
• Test door closure and latch engagement; adjust alignment if necessary

This factory screw secures dryer panels and internal components, keeping assemblies tight and aligned so the machine operates safely and without vibration or rattling.

• Fastens sheet-metal panels, brackets, or trim to the dryer cabinet/frame
• A loose or missing screw can cause panel vibration, noise, or misalignment
• Helps restore stability after service or when original hardware is lost
• Typical symptoms include rattling, loose panels, or gaps in trim

• Unplug the dryer before servicing
• Keep track of original screw locations and lengths; replace like-for-like
• Start screws by hand to avoid cross-threading, then snug—do not overtighten
• If threads are damaged, inspect mating hole or clip before installing

This fuse holder secures a 3AB-style cartridge fuse within the appliance's electrical circuit. Replacing a cracked, loose, or heat-damaged holder restores a solid connection so the fuse can properly protect the circuit and prevent intermittent power issues.

• Provides a secure mount and reliable electrical contact for a 3AB cartridge fuse
• Helps ensure the protected circuit opens correctly during electrical faults
• Common symptoms of a failed holder: fuse won't seat, loose/burned contacts, intermittent or no power
• Direct replacement when the original holder is broken, heat-damaged, or cracked

• Disconnect power at the breaker or unplug the appliance before servicing
• Note wire positions and transfer one lead at a time to the new holder
• Install only a manufacturer-specified 3AB cartridge fuse of the correct rating
• Ensure the fuse seats firmly and all connections are tight before restoring power

This dryer idler arm assembly keeps the drive belt tight and aligned so the drum turns smoothly. A worn or seized idler can cause squealing, belt slippage, or a drum that won't tumble.

• Applies tension to the drive belt and guides it around the motor pulley
• Maintains proper belt alignment for consistent drum rotation
• Common symptoms of failure: squealing/squeaking, belt coming off or wearing quickly, drum not turning, or burning rubber odor
• Pulley should spin freely; roughness or wobble indicates replacement is needed

• Disconnect power; if gas, also shut off gas supply before servicing
• Remove top/front panels as needed, release belt tension, and note belt routing
• Remove the old idler from its mount; transfer spring from the original if required by your model, then install the new assembly and re-route the belt
• Rotate drum by hand to verify belt tracking before reassembly and test run

The Dryness Control Board is an OEM part for GE dryers. This part monitors and regulates the drying process to detect the moisture level in the dryer drum. It adjusts the drying time and temperature accordingly, allowing your clothes to dry efficiently while preventing over-drying or under-drying.

A bad dryness control board can occur due to electrical malfunctions, damage, or wear and tear over time. If you notice symptoms such as clothes coming out damp, the dryer running for excessive periods, or error codes related to the drying process, it may be time to replace this part.

Symptoms of a bad dryness control board include:

• Clothes coming out damp
• Dryer running for excessive periods
• Error codes related to the drying process

Restore your GE dryer by replacing the faulty dryness control board with this genuine part. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.

This gas valve assembly regulates the flow of gas to the dryer's burner, enabling safe ignition and steady heat. Replacing a weak or failed valve restores reliable heating performance and helps clothes dry evenly. What it does:

• Opens and closes to control gas flow to the burner for proper ignition and heat.
• A failing valve can cause no heat, the burner not to light, or intermittent heating leading to long dry times.
• Helps ensure gas is shut off when not energized for safety.

• 1 gas valve assembly

• Disconnect electrical power and shut off the gas supply before servicing.
• Work in a well-ventilated area; avoid sparks or open flames.
• Transfer any model-specific fittings or brackets from the original part as directed by your service information.
• After installation, check all gas connections with an approved leak-detection solution and verify proper ignition.

A replacement shield switch that helps the oven/microwave detect door position so the unit runs only when the door is closed. Restores reliable door sensing and user safety by replacing a worn or damaged switch. What it does

• Acts as the door-position sensing switch to allow operation only when the door is properly closed
• Stops intermittent or failed start issues caused by a worn or faulty door switch
• Helps correct symptoms like oven/microwave not starting, stopping mid-cycle, or inconsistent door detection
• Works as the plug-in electrical switch used in the door/shield assembly

• Disconnect power at the breaker or unplug the appliance before starting any repair
• Access may require removing the door or control/vent panels
• Handle small metal parts and electrical connectors carefully; avoid bending terminals
• Test door operation and proper function after installation

This valve and pipe assembly regulates and routes water for the dryer's steam feature. A new assembly restores proper water flow, helping resolve no-steam operation, weak spray, or leaks at the rear water connection.

• Opens and closes to supply water to the steam system when commanded
• Directs water from the household supply through the attached tube to the steam outlet
• Prevents water from entering the dryer when the steam feature is off
• Typical symptoms: steam option won't spray, weak or intermittent mist, dripping into the drum, leaks at the rear inlet, or valve buzzing with no water flow

• Disconnect power and shut off the water supply before servicing
• Pull the dryer forward to access the rear and place a towel to catch residual water
• Note hose orientation; transfer any fittings or clamps from the old part as needed
• Restore water and power, check for leaks, and run a brief steam cycle to verify operation

This burner assembly is the combustion head for GE gas dryers. It mixes gas and air and directs a stable flame into the heater housing, restoring consistent heat when the original burner is corroded, warped, or clogged.

• Directs the gas flame into the heat chamber for proper drying temperatures
• Works with the igniter, flame sensor, and gas valve to produce heat
• Typical failure symptoms: no heat or intermittent heat, long dry times, burner lights then goes out, unstable/yellow flame
• Physical issues can include rust, warping, or blocked burner ports

• Disconnect power and shut off the gas supply; allow the dryer to cool completely
• Note position of the igniter and flame sensor relative to the burner port; realign during reassembly
• Transfer any reusable fittings from the original burner as needed and verify orifice/fuel type match your installation
• After reconnecting gas, perform a leak check with a non-corrosive soapy water solution before restoring power

This exhaust duct directs hot, moist air from the dryer's blower housing to the external vent. Replacing a cracked or leaking duct restores proper airflow, helps prevent lint leaks, and supports consistent drying performance. What it does:

• Routes exhaust air from the blower housing to the rear outlet and home vent
• Maintains a sealed airflow path for efficient drying and moisture removal
• Helps keep lint contained within the exhaust stream to the vent system
• Common failure symptoms: longer dry times, warm air or lint escaping, or visible cracks/damage to the duct

• 1 exhaust duct

• Unplug the dryer and shut off gas supply for gas models; allow the appliance to cool. Wear cut-resistant gloves.
• Remove the necessary panels to access the duct per your model's service information.
• Transfer and reuse existing screws and any foam seals/gaskets if not supplied; seat the duct fully and tighten fasteners evenly for an airtight fit.
• Vacuum lint from the cabinet and confirm the external vent hose is clear and securely attached before testing.

This leveling leg threads into the base of your appliance to provide a stable, adjustable footing. Replacing a worn or missing leg helps keep the cabinet level, reducing vibration and noise for smoother, safer operation.

• Adjusts height so the unit can be leveled on uneven floors
• Maintains solid floor contact to minimize rocking or walking
• Helps reduce vibration and rattling noises during operation
• Signs you need this part: appliance wobbles, sits unevenly, or a foot is missing/damaged

• Disconnect power; for gas units, also shut off the gas supply
• With assistance, carefully tilt or raise the appliance to access the leg
• Unscrew the old leg and thread in the new leg by hand; use a wrench if needed
• Level the unit front-to-back and side-to-side; ensure all legs firmly contact the floor

This complete microwave oven door assembly restores the oven's sealed cooking chamber and user access, helping stop heat or steam leaks and providing a secure, functional door surface. Use it to replace a cracked, bent, or non-closing door. What it does:

• Replaces the full microwave door so the oven seals and operates safely
• Restores the outer panel, inner trim and viewing area for normal use
• Helps resolve symptoms like a broken or cracked door, poor closure, rattling, or visible damage
• Re-establishes proper door alignment and latch engagement when installed correctly

• Disconnect power and unplug the appliance before beginning any repair
• Handle glass and trim carefully; wear gloves and eye protection if glass is cracked
• Installation may require removal of surrounding trim or control panel—retain all screws and fasteners

This replacement motor strap secures the dryer's drive motor to its mounting bracket so the motor and blower stay aligned and stable, helping reduce vibration and noise for smoother operation. What it does:

• Holds the drive motor firmly to the base/bracket
• Maintains proper alignment of the motor and blower wheel to prevent rubbing
• Helps reduce vibration, rattling, and related noise
• Typical signs of failure: increased vibration, rattling, scraping from the blower area, or a motor that feels loose inside the cabinet

• Includes 1 motor strap

• Disconnect power; for gas dryers, also shut off gas supply
• Access the motor assembly; note the strap's routing/orientation before removal
• Support the motor while releasing the strap to avoid stressing wiring and mounts
• After securing the strap, rotate the drum/blower by hand to verify free movement before reassembly

This plug button is a replacement cosmetic/functional cap that covers an unused control opening or receptacle on the appliance, restoring a finished appearance and helping keep out dust and debris. What it does:

• Covers and seals an unused control hole or plug location to improve appearance
• Helps prevent dust, lint, and small debris from entering the opening
• Restores a flush, finished look when a switch, knob, or connector is missing
• Simple snap-in design for a clean, low-profile result

• Disconnect power to the appliance before servicing.
• Typically snaps into place; no special tools required for most installations.
• If removal is needed, use a plastic pry tool to avoid scratching surrounding surfaces.
• Your appliance owner's manual or parts diagram to correct placement.

Replacement screw that secures appliance panels and internal components, restoring proper fit and helping prevent rattling or misalignment. Use this fastener when original screws are stripped, missing, or damaged to keep parts stable and secure. What it does:

• Secures panels, trim pieces, brackets and other components to maintain proper alignment and fit.
• Replaces stripped, corroded, or missing screws that can cause rattling, vibration, or loose parts.
• Restores stable mounting for service panels and access covers to reduce noise and movement during operation.
• Simple hardware replacement — helps prevent secondary damage caused by loose or shifted components.

• Disconnect power or gas (when applicable) before servicing to avoid shock or injury.
• Use the correct screwdriver or bit to avoid stripping the head; turn until snug—do not overtighten.
• Keep track of small parts and wear eye protection when working in tight spaces.
• If threads are damaged, replace with the correct OEM screw rather than forcing reuse.

Size: 8-32 t. Includes 12 screws.