Gtw680bsjws Parts

The Lid Lever Arm is an OEM part for GE washing machines. This component is crucial for the proper functioning of the washer's lid mechanism, ensuring that the lid locks securely during operation and allows for safe and efficient washing cycles.

Over time, the lid lever arm can become worn out or damaged due to regular use, improper handling, or mechanical failure. Causes of a bad lid lever arm include physical damage, wear and tear from repeated use, or issues with the linkage that connects it to the locking mechanism.

Symptoms of a bad lid lever arm include:

• The washer lid not locking properly
• The washing machine not starting or pausing unexpectedly
• Error codes related to lid lock issues
• The lid feeling loose or misaligned

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replace a failed speed sensor to restore accurate motor feedback for your washer. This sensor monitors drive speed so the control can regulate agitation and spin; when it fails, cycles can stall, stop, or skip spin. What it does:

• Monitors drive motor/basket speed and sends feedback to the control
• Enables precise regulation of agitation and spin speeds
• Failure can cause no-spin or no-agitate conditions and erratic cycle behavior
• May trigger fault codes related to speed sensing/tachometer feedback

• One speed sensor

• Disconnect power and turn off water before servicing
• Access the drive motor area (location varies by model); note connector orientation
• Transfer any mounting clip/screw if present; seat the sensor fully and secure wiring away from moving parts
• After installation, run a spin or service test to ensure proper operation

This lid lock harness clip secures the lid lock wire harness to the washer cabinet or top. It keeps the wiring routed and protected to help prevent chafing, snagging, and intermittent lid-lock performance issues. What it does / common symptoms:

• Holds the lid lock wire harness in place along the cabinet/top
• Maintains proper routing to avoid pinching or rubbing on moving parts
• Reduces vibration-related wear on the wiring
• Symptoms of a failed/missing clip: loose or dangling harness, scuffed insulation, intermittent lid-lock response

• 1 lid lock wire harness clip

• Disconnect power before servicing
• Access the lid lock wiring path (lift top/remove console as required by your model)
• Release the old clip from the panel and harness; snap the new clip into the mounting hole and secure the harness
• Ensure the harness has adequate slack and is not pinched before restoring power

This replacement siphon cap fits the washer's dispenser assembly. The insert creates the siphon action that empties the additive cup during the rinse cycle, helping prevent standing liquid and residue so liquid additives dispense as intended.

• Forms a siphon in the dispenser cup so liquids empty at the proper time
• Helps reduce standing water and residue buildup in the dispenser
• A worn or missing cap can contribute to odors or buildup in the dispenser area

• Unplug the washer and turn off water before servicing
• Remove the dispenser drawer or cup and lift out the old siphon cap
• Clean the dispenser area; press the new cap in firmly so it seats evenly
• Reinstall the drawer/cup and run a rinse to ensure proper dispensing

This screw is a factory fastener used to secure appliance components. Replace a missing, stripped, or corroded screw to keep panels, brackets, and assemblies tight and help prevent vibration or rattling from loose hardware.

• Secures panels, brackets, and internal assemblies at their mounting points
• Replaces lost, rusted, or stripped hardware for a solid, reliable hold
• Helps reduce vibration, rattling, or shifting caused by loose fasteners
• 1/4-20 thread per OEM designation for proper fit where specified

• Disconnect power and, if applicable, shut off water supply before servicing
• Start threads by hand to avoid cross-threading, especially in plastic
• Tighten snugly; do not overtighten to prevent stripping or cracking
• Verify alignment and stability of the secured component after installation

This washer recirculation tube carries wash water from the recirculation pump back to the tub's spray/waterfall outlet. Replacing a worn or damaged tube helps stop leaks and restores even soaking and detergent distribution.

• Routes water from the recirculation pump to the tub flume/spray during the wash cycle
• Cracks, splits, or loose connections can cause leaks under or inside the cabinet
• Kinks or blockages reduce or stop the recirculation stream, leading to poor cleaning results
• Replace if the tube is brittle, swollen, clogged, or visibly worn

• Disconnect power and turn off water supplies; place towels to catch residual water
• Access the tube routing path and note original orientation and clip points before removal
• Transfer/reuse clamps as needed; fully seat the tube on fittings and route exactly like the original to avoid kinks
• Reassemble and run a short test to check for leaks and proper spray/recirculation

The Top Cover is an OEM part for GE washing machines. It serves as the top panel enclosure for the washer, covering internal components and shielding them from potential water damage or intrusion of foreign objects. The top cover also plays a cosmetic role, providing a sleek design finish to the top of the appliance.

Symptoms of a bad top cover include:  

• Cracks, breaks, or looseness developing in the plastic material over time
• Missing or damaged mounting screws  
• Water leaks or moisture inside the panel enclosure area
• Dents, dings, or other exterior damage affecting appearance

Causes of a bad top cover are generally related to wear and tear from repeated usage and loading/unloading of clothes over the years. General handling can also lead to minor impacts or stresses that result in cracks or breaks.

This genuine GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This factory-spec screw secures internal brackets, housings, and panels. Replacing a missing, stripped, or corroded fastener with the correct #6-32 size restores a tight, corrosion-resistant fit that keeps assemblies aligned and helps reduce vibration noise.

• Provides #6-32 machine-thread fastening for appliance components
• Helps maintain alignment and stability of brackets, housings, and panels
• Replaces stripped, rusted, or missing hardware that can cause looseness or rattling
• Stainless construction resists corrosion in high-moisture areas

• Disconnect power and, if applicable, shut off the water supply before servicing
• Start threads by hand to avoid cross-threading; use the correct driver for the head type
• Tighten snugly without overtightening, especially into plastic or thin sheet metal

This harness wire tie secures and organizes the appliance's wiring harness. Replacing a damaged or missing tie keeps wires properly routed and protected to help prevent chafing, disconnections, and vibration noise for more reliable operation. What it does:

• Bundles and anchors wiring harnesses along the intended routing path
• Helps prevent wire insulation from rubbing, pinching, or wearing through
• Reduces rattling or vibration noise from loose wires
• Common signs include a broken/missing tie, dangling wires, or visible wear on the harness

• 1 harness wire tie

• Disconnect power before servicing; allow any moving parts to stop
• Note original wire routing and mounting location; take a photo for reference
• Install the new tie at the same point and snug it just enough to secure without crushing wires; trim excess strap
• Verify wires are clear of moving or hot components before restoring power

A small mounting support that provides a stable anchor point for screws used to secure panels or internal assemblies. Replacing a damaged screw platform restores proper fastener engagement and reduces panel movement and vibration. What it does:

• Anchors screws to hold trim, panels or internal components in place
• Restores secure attachment when the original mounting point is cracked or worn
• Helps eliminate rattling, loose panels, or alignment issues caused by a failed mounting surface
• Works with the appliance's existing screws and surrounding hardware to maintain structural fit

• Disconnect power to the appliance before attempting any repair
• Use the correct screws and a properly sized screwdriver to avoid further damage
• Inspect surrounding mounting points and replace any stripped screws or damaged clips as needed

White control panel that restores the front user interface and appearance of compatible GE ranges. Replaces a damaged or worn panel to provide a clean, finished surface for the controls and display. What it does:

• Provides the mounting/faceplate for the oven control area and display.
• Replaces cracked, broken or missing panels that expose internal components.
• Restores proper button/dial seating when the existing bezel is warped or damaged.
• Refreshes a discolored or faded front for improved appliance appearance.

• Disconnect power to the appliance (unplug or shut off the breaker) before beginning any work.
• Some installations require removing the control console or transferring controls; follow the OEM service instructions.
• Handle the panel carefully to avoid scratching or chipping the finish; use protected work surfaces.

The Lid Hinge is an OEM part for GE washers. It provides the mounting and fulcrum point for the washer lid, allowing smooth movement between open and closed positions. The sturdy hinge construction is designed to withstand repetitive use over many cycles.

Causes of a bad lid hinge can include fatigue from extended use, damage or loosening of mounting screws, or impact dents deforming the metal.

Symptoms include:

• Looseness, wobbling, or sagging of the washer lid 
• Difficulty fully opening or closing the lid securely
• Noise or squeaking emitted from the hinge area
• Physical deformation reducing the proper range of motion

This OEM GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. Replacing a worn or faulty lid hinge ensures comfortable, predictable lid movement for years to come.
 

The Clamp is an OEM part for GE washers. It is used to securely fasten critical components like hoses, sensors, and wiring harnesses in place inside the washer cabinet. 

As a machine that handles water, chemicals, and moving parts, a washer requires many clamps to organize its internal systems. They ensure hoses and electrical wiring remain properly positioned and protected throughout years of operation. Without solid clamps, connections could loosen or detach, leading to leaks or electrical faults.

Causes of a bad clamp can include fatigue from constant vibration, outright breakage from impact or tension overload, or rust/corrosion damage over extended use. 

Symptoms of a failed clamp include:

• Loose, disconnected or damaged hoses and wiring  
• Water leaks from hose connections
• Electrical or sensor errors

The clamp is also compatible with some Kenmore and other brands that use GE components.

This 10-32 hex head screw secures appliance panels and components where a small machine screw is required. It provides a durable, threaded fastening point for repair or reassembly. What it does:

• Fastens panels, brackets, and small components using a 10-32 machine thread
• Hex head accepts a 7/16" socket or wrench for positive torque application
• Replaces worn or damaged screws that cause loose or rattling parts
• Compatible with common metal-to-metal and tapped-hole connections

• One 10-32 hex head screw with 7/16" socket head

• Use the correct 7/16" socket or wrench to avoid rounding the head
• Thread engagement should match the appliance's threaded insert; do not force if resistance is felt
• Follow manufacturer service manual for torque specs and installation sequence
• Disconnect power and follow safety procedures before servicing the appliance

This clip spring cover is a small plastic retainer that secures the spring/clip assembly on compatible appliances, helping keep moving parts aligned and reducing rattles or loose components. Replaces a worn or broken cover to restore proper fit. What it does

• Covers and holds a spring or clip in place to prevent displacement during operation
• Keeps assemblies aligned to reduce noise and intermittent part contact
• Helps maintain consistent tension where a spring or clip is used
• Commonly replaced when the original cover is cracked, broken, or missing

• One clip spring cover

• High-level replacement; basic hand tools may be required to access the location
• Disconnect power (or unplug) and follow appliance safety procedures before servicing
• Inspect adjacent springs/clips for wear and replace if damaged

8-18 hi/lo 5/8