Gu2500xtp7 Parts

This is a small plastic positioner that clips onto the dishwasher rack and holds the tine rows in their adjusted positions, allowing you to customize the rack layout for different dish sizes. It snaps into place on the rack rails to lock folding tines upright or flat. Replace this part if the tine rows no longer stay in position, the positioner is cracked, or the clip has broken off.

Replacement plate holder clip assembly that secures the appliance's glass plate or tray to the drive hub, helping restore stable, even rotation and reduce wobble or slipping during use. What it does:

• Secures the glass plate or tray to the drive hub so it rotates evenly
• Helps prevent the plate from wobbling, scraping, or slipping out of position
• Can reduce noisy or irregular turntable movement
• Supports consistent heating by keeping the plate aligned

• Disconnect power before servicing the appliance to avoid electric shock
• Remove the glass plate and turntable support to access the clip; handle glass carefully
• Press the clip onto the drive hub or shaft until fully seated
• After installation, reinstall the plate and run a short test cycle to ensure smooth rotation

This kit includes hose clamps and fasteners used during dishwasher installation to secure the drain hose and water supply connections. It ensures tight, leak-free connections between the dishwasher and household plumbing. Replace this kit if you notice water leaking at hose connections or if clamps are corroded, broken, or missing during a new installation or reinstallation.

Includes 6` Stainless Steel Braided Hose, Power cord & Connectors

This is a rack adjuster mechanism that allows you to raise or lower the upper dish rack in your dishwasher. It attaches to the side rail and enables height adjustment to accommodate taller items on the lower rack. Replace it if the upper rack tilts, sags to one side, or the adjuster no longer locks into position.

Right-hand door hinge that restores proper door alignment and smooth operation. Replace if your dishwasher door sags, binds, or won't stay open. Verify fit.

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

Access panel covers the base of your dishwasher, concealing wiring and mechanisms. Replace if cracked, broken, or missing after installation.

Replacement mounting screw for dishwashers. Secures internal components and panels. Order a new screw if yours is stripped, missing, or damaged.

This is a small plastic or rubber fitting that secures the power cord where it enters the dishwasher's junction box or base. It prevents the electrical wiring from being pulled, kinked, or damaged by absorbing tension on the cord. Replace this part if it is cracked or missing, which can leave wiring exposed and vulnerable to damage during installation or use.

Fix leaks around the dishwasher motor or poor spray pressure with this impeller and seal kit. DIY-friendly repair takes about 2 hours with basic tools.

Dishwasher leaking from bottom or making grinding noise? The sump housing often cracks or wears out. Moderately difficult repair, about 45 minutes.

This replacement screw fastens appliance components such as panels, brackets, or trim. Use it to replace a missing, stripped, or rusty fastener and restore a secure, rattle-free fit in your appliance assemblies.

• Secures panels, brackets, or hardware to maintain proper alignment
• Helps eliminate vibration, rattling, or loose-feeling parts
• Replaces fasteners that are missing, corroded, or cross-threaded
• Typical signs you need it: loose handle or panel, gaps, or hardware that won't stay tight

• Disconnect power (and shut off gas, if applicable) before servicing
• Match thread type and length to the original fastener for proper fit
• Start threads by hand to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if present