Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This is the dishwasher manifold tube only. It attaches to the bottom of the upper rack. For the complete kit order 675808. Also consider checking the mount that attaches this manifold tube to the dishrack. For the mount order WP8539324.
Part was updated from original equipment (3 pieces) to a one piece tube. Snip the top of hanger loop then install. Just a couple minute job. Updated tube is much better than the original design. Read more
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Replaced It With New One Read more
includes seal
Replaced nut and then found we needed new pump. Read more
Included with nut.
I cleaned all the jet nozzles with a toothpick and a pipe cleaner to remove the hard water deposits. I then replace the ring bearing under the bottom spray wand and the ring bearing under the upper spray wand. I also replaced the smaller radial ring bearing. Although none of them looked overly worn, it doesn't take much to cause the spray wands to spray inadequately. Then, I replaced the float and washer assembly. Although it appeared to work properly when I lifted up on it and let it down, it... Read more
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy! Read more
There is a split at the 3 O'clock position. Color: white. It measures about 3 inches wide by 4 inches high.
I was able to purchase all needed parts through Appliance Parts Pros. It was an easy fix, and only took about 10 minutes. Read more
This dishwasher door spring restores proper counterbalance so the door opens smoothly and doesn't drop. The premium version provides the factory-specified tension used on select models for consistent, controlled door movement.
I ordered the parts, deciding that if one spring had broken, the other one should probably be replaced at the same time. I followed the suggestion of ordering the door spring bearing given on the ordering page, and since I had not yet pulled out the dishwasher, did not know that it was not used in this older model. However, the order arrived quickly (4 days), and they are genuine Whirlpool, made in the USA, parts. The access to the sides of the dishwasher where the springs are attached... Read more
This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.
1. To fix the leaks from around the door, I replaced the upper and lower door seals. These were purchased in a separate transcation, so they are not the parts shown here. The upper door seal worked as intended, but the lower seal would not stay in place on the lower edge of the door during a wash. Therefore I cleaned the grease and detergent off the old seal, and installed using silicone sealer/adhesive. The plastic edge pieces for the lower seal were supplied with the kit, and they installed... Read more
Detergent cup dispenser actuator assembly.
Received correct parts for Appliance Parts with ease and quickly. Read more
This felt door vent seal fits around the dishwasher's door vent to help contain steam and moisture within the inner door. Replacing a worn seal helps prevent minor leaks and condensation around the vent area during cycles.
Replaced the felt seal and door vent assembly by removing the inside panel of the door and cleaning off the old seal and replacing with the new one. The vent assembly simply snapped out and was easy to replace with the new one. No more leaks and Mother was happy. Removal of the screws required a torx screw driver and someone to hold the door open while the panel was replaced. Easy fix. Read more
Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.
Ordered 2 infinite burner controls from Appliance Parts Pros and watched the online video on the replacement of them at the same time. When they arrived promptly, I was ready to take on the job. The fix only took about 15 minutes because I was prepared after watching the video. Read more
Includes washers.
Replacement heater element installed exactly as described in the AppliancePartsPros video. Read more
Size: 7 foot long.
Bought the parts and connected same...a breeze in finding and receiving and eventually installing these parts. Read more
Almond. Size: 13 oz. can. Acrylic appliance paint.
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !! Read more
This replacement screw secures appliance panels and components so they stay tight and aligned. Replace a missing, rusty, or stripped fastener to restore a solid hold and reduce vibration or rattling during operation. What it does:
This is a tine pivot clip that is a part of the dishrack on many models of dishwashers. The purpose of the plastic tine pivot clip is to secure the tine row onto the dishrack so it stays in the correct place. Sometimes, the tine pivot clip can be damaged or cracked through typical use. When this occurs, the tine row may move out of place and cause noise or other damage to the dishwasher. If a visual inspection shows damage to the tine pivot clip, it should be replaced.Work gloves will be needed to replace the tine pivot clip. In most cases, the replacement can be done by hand but pliers may also be useful. Unplug the dishwasher and disconnect the water before making the replacement. Open the dishwasher and gain access to the tine pivot clip. Pull it out of the dishwasher and install the new replacement part. Make sure to reconnect the water and power before use.This is a genuine OEM replacement part that is directly sourced from the manufacturer. It is sold as a single part. The tine pivot clip is designed to be compatible with dishwashers manufactured by Kenmore, KitchenAid, and Whirlpool.
I watched a couple of your on line videos, brought the parts and fixed the dish racks. Easy. Kitchen Aid label with serial number worn out. Read more