Gud24 Parts

This shifter spring helps engage and return the transmission shifter mechanism in select top-load washers, allowing smooth changes between agitation and spin for reliable wash performance.

• Maintains proper tension on the shift mechanism between agitate and spin
• A worn or broken spring can cause no spin, no agitate, or loud shifting noises
• May also lead to intermittent shifting or incomplete cycles
• Restores consistent mechanical engagement of the drive system

• Unplug the washer and shut off water supply before servicing
• Access is typically from the cabinet/rear; support the tub to prevent movement
• Note spring orientation and attachment points before removal
• Use needle-nose pliers or a spring tool; replace any severely worn mating parts

Fix a washer that won't spin or stops after a few seconds. This speed sensor regulates wash basket rotation for proper cleaning. Moderate difficulty repair.

Fix a washer that won't spin with this clutch assembly. Restores proper spin speeds and reduces excessive noise during the spin cycle. DIY repair.

This lid actuator engages the washer's lid switch or lock when the lid closes, signaling the control that it's safe to run. Replacing a worn or broken actuator restores reliable lid detection for wash and spin cycles.

• Engages the lid switch/lock when the lid is closed
• Signals the control to allow the washer to start and spin
• A damaged or missing actuator can lead to "lid open" errors
• Common symptoms include won't start, won't spin, or lid lock light flashing

• Disconnect power before servicing
• Access the lid switch/lock area; remove the failed actuator
• Install the new actuator, aligning it to the original mounting points; reuse existing hardware
• Close up and test lid detection before running a full cycle

Fix loud clunking or grinding noises during spin cycle with this transmission platform assembly kit. Connects transmission to tub for proper operation.

Fix a washer that won't drain or leaves standing water. This drain pump removes water from the tub after each cycle. Moderate DIY repair.

This replacement part is a high-limit thermostat, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This high-limit thermostat is typically found in dryers and controls the heat inside the drying tub. This is especially important as different dryer settings require different amounts of heat. If the high limit thermostat works properly, the temperature inside the tub should reach the correct amount during each drying cycle with no issues. A new high-limit thermostat might be needed if the user notices that the dryer is unable to reach the appropriate level of heat for a certain drying cycle. This is also true if the dryer is becoming too hot when the heat is supposed to be set to low. Make sure the dryer is cooled down prior to replacing this part as the areas in the back of the dryer can become very hot during use. Be sure to reference the specific user manual for more instructions on how to replace the thermostat. This thermostat is sold individually and is a genuine OEM part. The thermostat is sourced directly from the manufacturer.

Fix out of balance errors and excessive vibration during spin cycles. This suspension rod assembly stabilizes the tub. Moderate difficulty repair.

The Tub Cover is an OEM component for GE front-load washing machines. It provides a protective barrier around the inner tub and mechanism while blending into the washer design.

Causes of a faulty tub cover can include cracking, bending, or warping from repeated use over several years. Excessive exposure to moisture or impacts can accelerate damage. 

Symptoms of a bad tub cover include:

• Water leaks inside or outside the washer during operation
• Unsecure door closure or door alignment issues
• Visible dents, cracks or punctures in the plastic material

This tub cover replacement is also compatible with models by Hotpoint, RCA, and some Kenmore brands.

The Rod Assembly is an OEM part for GE washing machines. It consists of the shaft and drive rod that connects the motor to the tub's agitator or impeller. As such, it plays an integral role in facilitating the transmission of power from the motor to drive the agitation and washing action.

Causes of a bad rod assembly can include cracks, bends, or breaks from stress and fatigue due to extensive use over time.  

Symptoms of a bad rod assembly include: 

• No agitation or spinning despite the motor running 
• Excessive vibration and noise from the tub area
• Disconnected or slipping components between the motor and tub

This OEM GE replacement rod assembly is also compatible with some Hotpoint, RCA, and Kenmore models. 

Inner wash basket kit for laundry center units. Holds clothes during wash and spin cycles. Replace if cracked, damaged, or balance ring is broken.

Drain hose assembly routes wastewater from the washer pump to your standpipe or laundry tub. Replace if cracked, kinked, leaking, or causing floor puddles.

Fix washer cycles not registering or settings not responding. This 3-switch selector assembly restores control panel input. Moderate difficulty repair.

Dryer not heating or shutting off mid-cycle? A faulty safety thermostat can cut heat when temperatures climb too high. Direct heater duct mount part.

Seals joints between washer components to prevent leaks. Replace if flattened, cracked, or causing drips from the tub bottom. Confirm fit with your model.

The UPPER BALL JOINT is an OEM component specifically designed for GE washers. It is found on the center post of the tub and allows the outer tub to pivot front to back during agitation cycles. This precise movement helps optimize cleaning performance by maximizing water and pressure distribution.

Causes of a bad upper ball joint can include wear and tear over time, damage due to impact or misalignment, or unbalanced loads that put added stress on the joint. 

Symptoms of a bad upper ball joint include:

• Excessive noise or squeaking coming from the center post area
• Hampered or sluggish movement of the outer tub during washing  
• Leaks developing around the center post 

Replace yours today with this genuine OEM GE part for reliable front-to-back agitation and smooth cycle operation. This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.