Hbl8650 Parts

This heating element restores proper water temperature and drying performance in your dishwasher. When the original fails, cycles may run long and dishes can come out wet; replacing it brings back consistent, efficient cleaning results. What it does:

• Heats wash and rinse water to help dissolve detergent and remove soils
• Raises final rinse temperature to improve drying performance
• Works with the control and sensors to maintain target temperatures
• Common symptoms include water not heating, poor drying, extended cycles, or a heating-related fault

• 1 heating element

• Disconnect power at the breaker and shut off water before servicing
• Pull the dishwasher and/or remove the toe panel as needed to access the heater wiring and mounts
• Note wire positions and make secure, clean terminal connections
• After reassembly, run a test cycle and inspect for leaks and proper heating

This socket is an electrical connector used to join wiring or plug-in components, restoring a secure connection for reliable appliance operation. It replaces a worn or damaged socket to help prevent intermittent power or component failure. What it does:

• Provides a secure electrical connection between wiring and the appliance component
• Restores proper contact when a loose, corroded, or broken socket causes intermittent operation
• Helps prevent arcing or poor connections that can lead to component failure
• Used where a plug-in or push-fit electrical connection is required

• One socket

• Disconnect power to the appliance before inspecting or replacing the socket
• Replace only with the exact socket type specified for your appliance

This halogen oven lamp provides bright, consistent interior lighting so you can easily check cooking progress without opening the door. It replaces a burned or dim oven bulb to restore full interior visibility. What it does:

• Illuminates the oven cavity for clear viewing of food during cooking and baking
• Replaces a burned-out or flickering oven lamp
• Helps you monitor doneness without repeatedly opening the oven door
• Fits into the oven lamp socket and powers with the oven's existing lighting circuit

• Disconnect power to the appliance before servicing to avoid shock
• Allow the oven to cool completely before replacing the lamp
• Avoid touching the bulb glass with bare fingers; use gloves or a clean cloth to prevent oil deposits that can shorten bulb life

This grille for pan is a replacement trim piece that restores proper airflow and appearance around the appliance pan. It helps keep the pan area protected and looking finished after repair. What it does:

• Covers and ventilates the pan opening to help direct airflow and prevent debris entry
• Replaces a cracked, warped, or missing grille to restore fit and finish
• Helps eliminate rattling or rubbing caused by a damaged trim piece
• Matches OEM fit so it installs cleanly with the original mounting points

• Install requires removal of the surrounding trim or access panel; follow your appliance manual
• Handle carefully to avoid scratching the finish; use non-marring tools as needed
• Disconnect power to the appliance before working in the service area
• Replace damaged clips or screws with OEM fasteners for secure fit

This metal mounting bracket secures internal components and panels to restore proper alignment and reduce rattling. It's a straightforward replacement part that helps keep appliance panels and assemblies firmly in place for reliable operation. What it does:

• Provides a secure attachment point for panels or internal assemblies to prevent movement and vibration
• Helps correct alignment issues that can cause rubbing, gaps, or noise
• Restores the original fit where a bent, cracked, or missing bracket caused loose parts
• Works with the appliance's existing fasteners and mounting points

• Remove power and, if applicable, disconnect the appliance from water before beginning work
• Use the factory fasteners or OEM replacement screws to secure the bracket in the original location
• Verify alignment of the attached panel or assembly before fully tightening fasteners

This cap is a direct-fit replacement closure used to protect and seal an exposed opening or component on compatible Bosch appliances, preventing dirt, moisture and damage for reliable operation. What it does:

• Covers and seals an exposed port or fastener to keep contaminants out
• Protects internal components from moisture and debris that can cause malfunctions
• Replaces cracked, warped or missing caps that allow leaks or debris intrusion
• Restores proper fit and appearance where a damaged cap leaves an opening

• Disconnect appliance power and water supply before starting any repair
• Verify the cap matches the damaged/original part before installation
• Press or snap the cap into place until fully seated; do not force or pry
• Inspect mating surfaces for damage or debris and clean before installing

This electronic control module manages and times dishwasher cycles, buttons, and displays so your appliance responds correctly to selections and runs programmed wash sequences. Replacing a failed control restores normal cycle control and user interface operation. What it does:

• Controls wash, rinse, and drying cycle sequences and timings
• Interprets front-panel inputs and starts or cancels selected cycles
• Communicates status to display/LED indicators and other internal components
• Stops operation or prevents cycles when internal faults or errors are detected

• One control module

• Disconnect power at the breaker before beginning any service to avoid shock
• Access typically requires removing the console or inner door panel; handle electronics with care
• Observe static-sensitivity precautions and avoid touching circuit traces or components

This support mounting bracket secures internal components to the appliance frame, restoring proper alignment and stable operation. It replaces a worn, broken, or loose support to help reduce rattling and prevent component sag. What it does:

• Provides a secure mounting point for internal parts and assemblies
• Re-establishes correct alignment when a bracket is bent or broken
• Helps reduce vibration and rattling caused by loose or damaged supports
• Commonly replaced when a component shifts, rubs, or no longer sits flush

• Disconnect power and water before starting any repair.
• Basic hand tools are typically required; follow OEM service instructions for disassembly/reassembly.
• Inspect adjacent fasteners and clips; replace any that are damaged to ensure a secure fit.