Hmc801252 Parts

This plastic-foil capacitor is used in the appliance's electrical circuit to provide stable capacitance. It supports proper motor and power-circuit operation, helping components start and run smoothly while minimizing electrical noise. What it does:

• Stores and releases electrical energy to support motor starting/running or stabilize the power circuit
• Helps reduce electrical noise and voltage spikes in the system
• A failing capacitor can cause hard starting, humming, weak or intermittent operation, or tripped breakers
• Visible bulging, cracks, or heat damage on the capacitor indicates replacement is needed

• 1 capacitor

• Disconnect power at the breaker before servicing; verify no power is present
• Capacitors can retain a charge—discharge safely using appropriate tools and procedures
• Note wire positions and terminal orientation; transfer one lead at a time or take a reference photo
• Mount securely and keep wiring clear of sharp edges, heat sources, and moving parts

This replacement grid restores a stable, properly fitting surface in your appliance. It supports items and allows airflow or drainage as designed, helping maintain safe, reliable performance.

• Provides a rigid, open-grid surface for support and spacing
• Helps maintain proper airflow or drainage through the area
• Replace if bent, cracked, missing, or excessively worn
• Common signs include poor fit, wobbling, tipping items, or visible damage

• Disconnect power and, if applicable, shut off gas/water before service
• Allow all hot surfaces to cool completely
• Remove the old grid and clean the seating/mating points
• Set the new grid securely in place and verify a stable, level fit

This replacement screw secures appliance panels and components at their mounting points. Swap in a new screw to restore a tight, rattle-free fit when the original fastener is missing, stripped, or corroded.

• Fastens the designated panel, bracket, or component in place
• Replaces a missing, stripped, or rusted screw
• Helps address loose panels, gaps, rattling, or misalignment at the mounting point
• Maintains proper assembly integrity after service or vibration

• Disconnect power; shut off water supply if working near plumbing
• Match to the removed fastener and replace one at a time to preserve alignment
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly and avoid overtightening, especially into plastic or thin sheet metal

This circular heating element sits around the oven's convection fan and supplies the heat used in convection modes. Replacing a failed ring heater restores fast, even convection baking and consistent temperature control. What it does:

• Provides the primary heat source for convection bake/roast by surrounding the fan
• Helps maintain even temperature and airflow during convection cycles
• Common fix when convection mode won't heat or preheats slowly
• Replace if the element is open, blistered, or visibly broken

• One ring-style convection heating element

• Disconnect power to the oven/range before servicing
• Access is typically from the rear or by removing the interior fan cover; note wire positions before removal
• Avoid bending the element; transfer any brackets as required and secure mounting screws
• Reconnect wires firmly and test operation before reinstalling panels

Temperature regulator that monitors and controls an appliance's operating temperature to help maintain set points and stable performance. Replacing a faulty regulator can restore consistent temperature behavior and reliable operation. What it does:

• Senses and regulates temperature to maintain the appliance's set point.
• Signals the appliance's heating or cooling system to cycle on and off as needed.
• Common symptom: appliance temperature is too high or too low.
• Common symptom: temperature fluctuates or fails to stabilize.
• Common symptom: heating/cooling runs continuously or not at all.

• Disconnect power to the appliance before starting any service.
• Handle electrical connections and terminals with care; note wire locations before removal.
• Follow the appliance service manual or wiring diagram for proper placement and orientation.

This replacement screw secures appliance panels, brackets, or internal components. Swap out missing, stripped, or corroded hardware to restore a tight, rattle-free fit and keep assemblies properly aligned for reliable everyday use.

• Fastens panels, brackets, or subassemblies to the appliance frame
• Helps maintain alignment and reduce vibration and rattling
• Direct replacement for a worn, corroded, or missing screw
• Typical symptoms: loose panels/handles, gaps or misalignment, rattling noises, visibly missing fastener

• Disconnect power; also shut off water or gas before servicing
• Match head/driver type and length to the original; start threads by hand to avoid cross-threading
• Reuse any original washers or spacers if present
• Tighten snugly—do not overtighten to prevent stripping threads or damaging plastic mounts

This cable harness routes power and signals between appliance components to restore electrical connectivity and reliable operation. It's a direct replacement harness designed to match the original wiring configuration and connectors. What it does:

• Replaces a damaged or frayed wiring harness to restore power and control signal paths
• Ensures proper connector fit for reliable component-to-component communication
• Prevents intermittent faults caused by loose, corroded or cut wires
• Helps eliminate failures, error codes, or non-responsive controls tied to wiring issues

• One cable harness as pictured

• Disconnect power to the appliance before starting any work
• Match wire colors and connector shapes to the original harness before disconnecting
• Route and secure the harness away from heat sources and moving parts

This is a replacement mounting washer that helps secure fasteners and distributes load to protect appliance parts from wear and loosening. It's a small but essential hardware piece for stable, reliable assembly. What it does:

• Provides a stable bearing surface between a fastener and the appliance part to reduce wear
• Helps distribute clamp force to prevent pull-through or damage to softer materials
• Reduces loosening from vibration and movement that can cause noise or misalignment
• Restores correct spacing where a worn or missing washer causes loose fittings or rattling

• One mounting washer

• Turn off power and disconnect the appliance before accessing internal components
• Match orientation and location to the original washer; replace like-for-like using the same mounting hardware
• Use correct size fastener and torque to avoid over-compression or stripping
• If other hardware shows wear or damage, replace fasteners and adjacent parts at the same time

This genuine screw secures panels, brackets, and other components in your appliance. Replacing a missing, rusted, or stripped fastener restores a snug fit, reduces vibration, and helps keep assemblies properly aligned during daily use.

• Fastens panels, brackets, or covers to the appliance chassis
• Helps maintain alignment to reduce looseness and vibration
• Replaces missing, corroded, or stripped hardware

• Disconnect power and shut off water/gas before servicing
• Support the panel or component while removing the damaged screw
• Start the new screw by hand to avoid cross-threading, then tighten until snug—do not overtighten
• If the receiving clip or hole is stripped, repair or replace that hardware before reinstalling

This bottom heater is the oven/dryer heating element that generates heat for normal operation, restoring proper heating when the original element fails. It installs in the appliance's lower heater area to warm air or baking surfaces as designed. What it does:

• Produces heat for the appliance's lower heating chamber to enable normal drying or baking cycles
• Restores proper heating when the original element is burned out or broken
• Resolves symptoms like no heat, weak heat output, or uneven heating in the lower cavity
• Works as the core heating component; failure can cause longer cycles or incomplete drying/cooking

• One bottom heater

• Disconnect power (and gas supply, if applicable) before servicing to avoid shock or injury
• Access typically requires removing the lower access panel or back panel; follow your model's service manual
• Handle the element carefully to avoid damage; ensure all electrical connections are secure and correctly routed

This glass cover replaces a damaged or missing exterior glass panel to restore the appliance's appearance and protect internal components from dirt and contact. It provides a clean, finished surface that matches the original fit. What it does:

• Replaces cracked, chipped, or broken glass to improve safety and appearance
• Shields internal components from debris and everyday contact
• Restores the appliance's original exterior finish
• Helps ensure proper fit of adjacent trim and controls

• One glass cover

• Handle carefully to avoid breakage and wear protective gloves when installing
• Follow the appliance manufacturer's disassembly and reassembly instructions
• Disconnect power to the appliance before beginning any repair

This cable harness is a factory-style wire assembly that routes power and signals between components for proper appliance operation. It restores secure electrical connections and helps resolve intermittent power or control issues caused by damaged wiring. What it does:

• Re-establishes electrical continuity between control, sensors, and motors
• Replaces frayed, pinched, or broken wires that cause intermittent failures
• Restores reliable connector fit to prevent arcing and signal loss
• Helps eliminate symptoms such as no-start, control faults, or erratic operation

• One cable harness wire assembly as shown

• Disconnect power (unplug or switch off breaker) before installing to avoid shock
• Compare connectors and wire routing to the old harness before connecting
• Use proper strain relief and secure clips; avoid sharp bends or pinched wiring

This control panel replaces a damaged or worn user console to restore button access and the appliance's front appearance. It provides the tactile surface and openings for the unit's controls and display elements. What it does:

• Replaces cracked, faded, or scratched front control surface
• Restores access to buttons, touch areas, and visible indicators
• Helps address unresponsive or hard-to-read control interfaces when the panel is the damaged component
• Returns the appliance's finish and user-operating area to factory appearance

• Disconnect power to the appliance before starting any repair
• Handle the panel carefully to avoid scratching or chipping during installation
• Some installations require removing the console or control housing; keep fasteners and small parts organized
• If the control electronics or display do not function after installation, verify the underlying control assembly and connectors