Htmx100ed0ww Parts

This PTC start relay mounts on the refrigerator compressor and briefly energizes the start winding, then automatically opens as it warms. Replacing a weak relay helps restore reliable compressor starts and consistent cooling. What it does:

• Provides momentary power to the compressor's start winding at startup; the PTC element opens as it heats
• Helps ensure smooth compressor starts and reduces repeated start attempts
• Signs of a failed start device can include no cooling because the compressor won't run
• Clicking or buzzing from the compressor area every few minutes
• Compressor starts intermittently or stops shortly after starting

• Includes: 1 PTC start relay

• Disconnect power and pull the refrigerator forward to access the rear service area
• Remove the rear panel to reach the compressor compartment
• Unplug the wire harness and pull the old relay straight off the compressor terminals; note its orientation
• Push the new relay fully onto the compressor prongs, reconnect the harness, reinstall the panel, and restore power

This Hi-Lo truss-head screw secures plastic and sheet-metal components in your refrigerator. Replacing stripped or missing fasteners restores a tight, rattle-free fit and keeps brackets, trim, and covers properly aligned.

• Fastens brackets, panels, trim, covers, and other components to the cabinet or liner
• Hi-Lo thread design grips plastic or thin metal for a strong, reliable hold
• Helps address loose or vibrating parts, rattling noises, and misaligned covers
• Direct replacement for a missing, worn, or damaged mounting screw

• Disconnect power before servicing any appliance
• Support the part being secured to avoid stress or misalignment
• Start the screw by hand to prevent cross-threading; use the correct driver
• Snug firmly but do not overtighten, especially when threading into plastic

This flip-up dairy door covers the refrigerator's dairy compartment. Replace a cracked or missing cover to keep butter, cheese, and other small items organized and protected while restoring a clean, finished look to the fresh food door.

• Attaches to the dairy bin on the fresh food door and flips up/down for access
• Helps keep contents contained and protected during door opening/closing
• Restores proper hinge/latch engagement so the bin stays closed
• Common symptoms: cracked cover, broken hinge tabs, loose hinge, or missing door

• Empty the dairy bin and remove the old cover
• Align hinge tabs with the bin's pins and snap into place; no tools typically required
• Handle carefully; if very cold, let the plastic acclimate to room temperature before installation
• Open and close to confirm smooth operation and full seating

The Evaporator Fan Motor is an OEM part for GE refrigerators. This part circulates air over the evaporator coils, facilitating proper cooling and airflow throughout the refrigerator compartments.

Causes of a bad part can include normal wear and tear over time, bearing failure, electrical issues preventing the motor from running, or debris obstructing the fan blades.

Symptoms of a bad Evaporator Fan Motor include:

• Inadequate cooling or warm temperatures in the fresh food or freezer sections
• Frost buildup or moisture accumulation
• Loud or unusual noises coming from the fan area
• Complete failure of the fan to operate

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The defrost timer governs the automatic defrost cycle, periodically switching the refrigerator from cooling to defrost. Replacing a failed timer restores reliable defrosting to limit frost buildup and help maintain steady, consistent temperatures. What it does:

• Advances the system through run and defrost periods at set intervals
• Sends power to the defrost heater during defrost, then returns the unit to cooling
• A failed timer may cause heavy frost on the evaporator, poor cooling, or continuous running
• A timer that does not advance or is stuck can leave the refrigerator in defrost or prevent defrost entirely

• 1 defrost timer

• Disconnect power before servicing
• Access location varies by model
• Photograph wire positions; move wires one at a time to the matching terminals on the new timer
• Transfer any mounting bracket, secure the timer, and restore power to verify operation

This screw is a genuine General Electric part, sold individually. This screw can be used as a replacement part for a refrigerator. A screw can suffer damage in the lifespan of a refrigerator. It can also be easily lost or misplaced. Screws are small parts and are usually installed in multiples to ensure components are reliably attached, so one screw loosening or going missing might not necessarily affect the operability of the refrigerator. However, if the components loosen or the screw suffers damage that strips the part, such as punctures or erosion to the metal material from general wear and tear or from a direct impact, the screw should be removed and replaced with this genuine OEM replacement part. This is an OEM part sourced directly from the manufacturer, and it is sold individually. This screw is compatible with the following appliance brands: General Electric, Hotpoint, RCA, and Americana.

The Compressor Overload and Start Relay is an OEM part for GE refrigerators. It plays a crucial role in starting the refrigerator’s compressor and protecting it from electrical overloads.

Over time, these components can fail due to electrical wear, overheating, or repeated cycling. This can cause the refrigerator to malfunction or stop working altogether.

Symptoms of a bad compressor overload and start relay include:

• The refrigerator not cooling properly
• Clicking noises from the back of the refrigerator
• The compressor not running
• Overheating of the refrigerator

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This control housing is the molded frame for the refrigerator's control area. It supports and protects the control components and trim. Replacing a damaged housing restores proper alignment and secure mounting so adjustments and buttons engage correctly.

• Provides the mounting structure for control components behind the panel
• Keeps buttons/switches aligned for reliable actuation
• Helps protect wiring and control parts from vibration and impact
• Symptoms of a failed housing can include cracked plastic, broken tabs, a loose or sagging control panel, or buttons that don't press cleanly

• Disconnect power to the refrigerator; shut off water if working near the dispenser area
• Remove trim/cover and mounting screws; release locking tabs to remove the old housing
• Transfer existing switches, boards, and hardware to the new housing
• Reinstall, restore power, and verify proper control operation

This Door Spacer positions the refrigerator door components with the correct clearance so the door swings smoothly and sits level. Replacing a worn spacer can restore alignment, reduce rubbing or squeaks, and help maintain proper gasket contact.

• Maintains proper spacing and alignment of the door assembly
• Helps the door open and close smoothly, reducing friction and wear
• Can address issues like door rubbing, squeaking, or not sitting level
• Supports consistent gasket contact for a reliable seal

• Unplug the refrigerator before servicing
• Support the door and remove the necessary hardware to access the spacer location
• Note spacer orientation; install the new spacer and reassemble
• Adjust hinges if needed

Restore accurate cooling with this refrigerator temperature control thermostat. The cold control senses compartment temperature and opens or closes the circuit to cycle the cooling system, helping maintain your selected setting when the original control becomes unreliable.

• Monitors refrigerator air temperature via a sensing bulb
• Opens/closes electrical contacts to cycle the cooling system
• Maintains the temperature you select with the control knob
• Common symptoms of a failing control: temperatures too warm or too cold, refrigerator runs constantly or won't start, no response to knob adjustments

• Disconnect power to the refrigerator before servicing
• Access the control housing and note wire locations and the exact routing/placement of the sensing bulb
• Transfer any mounting hardware and the control knob from the old part; install the new thermostat
• Route and secure the sensing bulb exactly as original—do not kink the capillary; restore power, set to a mid setting, and allow temperatures to stabilize before fine-tuning

This freezer shelf assembly restores stable, level storage space in the freezer compartment. Replace a cracked or missing shelf to keep food organized and maintain proper spacing for consistent cold-air circulation.

• Provides a sturdy, level surface to store and organize frozen items
• Helps maintain proper airflow and spacing for efficient cooling
• Replace if the shelf is cracked, bent, broken, or missing
• Common signs include sagging under normal load or not staying seated in side supports

• Unplug the refrigerator before servicing
• Remove items from the area, then lift/slide the old shelf out of the side supports or tracks
• Position the new shelf in the same slots and fully seat both sides
• Verify the shelf is level and secure before loading items

This reversible door plug fills the unused mounting hole when you switch the door swing on your refrigerator. It restores a finished appearance and helps keep air and moisture from entering through the opening.

• Covers the unused door hole created during a door swing reversal
• Helps maintain proper sealing and resists drafts/condensation at the opening
• Restores a clean, finished, factory look to the door
• Common symptoms: missing or cracked plug, exposed hole, cosmetic gap on door edge

• Disconnect power before servicing any door components
• Gently pry out the old plug with a plastic trim tool to avoid scratches
• Align the new plug with the opening and press until fully seated and flush
• Verify the door closes properly and the gasket seals evenly

This defrost timer cycles the refrigerator in and out of defrost at set intervals. By powering the defrost heater and then returning to cooling, it clears frost from the evaporator so airflow and temperatures remain stable.

• Switches power to the defrost heater on a timed schedule, then back to the compressor and fans
• Helps prevent heavy frost buildup on the evaporator coils
• Failure may present as persistent frost, warm sections, the unit stuck in defrost (no cooling), or continuous running
• May also cause irregular clicking or a timer that won't advance

• Disconnect power before servicing; wear cut-resistant gloves
• Access the control housing or machine compartment, note wire positions, and remove the original timer
• Transfer any mounting hardware/bracket, orient the new timer like the original, and reconnect wiring securely
• Manually advance the timer if applicable to confirm switching, then restore power and monitor operation

This power cord assembly supplies electrical power from the wall outlet to your refrigerator. Replace a cut, frayed, or overheated cord to restore safe, reliable operation and eliminate intermittent power loss caused by a damaged cord. What it does:

• Provides the electrical connection between the household outlet and the refrigerator's wiring
• Helps resolve no-power or intermittent power when the cord is moved
• Addresses visible damage such as cuts, cracks, fraying, or a melted/discolored plug
• Mitigates arcing, sparking, or a burning odor originating from the cord or plug area

• One power cord assembly

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Pull the refrigerator forward for access; note the original cord routing and connections
• Install the new cord along the same path and secure any built-in strain relief; ensure the ground connection is properly seated
• Restore power and verify operation

This replacement clamp secures lines or components inside the refrigerator, keeping them properly routed and stable. Replacing a broken or missing clamp helps reduce vibration and prevents rubbing damage or leaks from loose tubing. What it does:

• Holds tubing or wiring harnesses securely in place inside the refrigerator
• Maintains correct routing and clearance to prevent chafing and wear
• Helps reduce vibration and rattling noises from unsecured lines
• Can help prevent drips or leaks when used to retain water tubing

• 1 clamp

• Unplug the refrigerator and, if working with water lines, shut off the water supply
• Note the original clamp orientation and routing; take a photo before removal
• Install the new clamp in the same location, securing lines without pinching or over-stressing them
• Restore power (and water if applicable) and check that lines are secure; inspect for leaks if used on water tubing