We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Size: 10-24 x .50 HXNI.
Most orders arrive by Wednesday, November 25
A stabilizer bracket that secures and supports internal components to reduce movement and rattle during operation. Helps restore stable alignment so the appliance runs quieter and more reliably. What it does:
I followed the Appliance Parts Pro's advice videos for the Maytag MAV6451AWW Atlantis washer on replacing the snubber ring and the suspension springs. Everything went just fine except replacing the two rear most suspension springs. None of the videos illustrated REINSTALLING the REAR springs which is extremely difficult because you can't get enough leverage with your arm extended. Observing my frustration, my wife recommended taking off the back side. You can't simply take off the back,... Read more
This locknut is a small threaded retaining nut used to secure rotating and stationary appliance components, helping keep assemblies tight and stable during operation. It prevents parts from loosening and reduces vibration-related issues. What it does:
Standard 8-18 x 3/8 inch mounting screw for securing panels, brackets, and components in appliances. Replace missing, stripped, or damaged screws.
Prevents oil leaks from the transmission area. Replace if you see oil puddles under your washer. Confirm fit with your model number before ordering.
I had a lot of problems removing the spin hub, I had to use an air impact wrench to un screw it even then it was very hard, it did not go easy with the hammer & pipe wrench as shown in the video. It was also very hard to remove the bottom spin bearing I had to cut the bearing retainer with a dremel tool so I could get my puller on it. After I struggled to get it apart The repair went very easy, I used brake spring pliers to remove the springs it worked like a charm. I am very pleased with... Read more
Usually ships within 4 - 14 days
Motor plate isolator.
This motor isolator is a rubber mounting that cushions and secures the washer motor, reducing vibration and noise during spin cycles and helping protect the motor and chassis from premature wear. What it does:
Washer won't start or stops mid-cycle? This lid switch housing secures the switch assembly for reliable lid detection. Simple DIY fix in minutes.
Mounting screw used to secure panels, trim, brackets, and small appliance components. Replace a missing or damaged fastener to restore proper fit, reduce vibration, and keep parts aligned for safe operation. What it does:
New parts did the trick. Very easy to replace. Did not need to replace the base agitator, the fabric dispenser, or the screw; but, while it was apart it was simple to do. Read more
This is a top cabinet hinge used on a washing machine. It connects the top panel to the washer cabinet, allowing the panel to pivot open for access to internal components. Replace this hinge if it is bent, broken, or corroded, or if the top panel no longer opens, closes, or sits flush properly.
Size: 1.25OD x .530IDX.
Drive motor isolator.
Fixes squealing or slow stopping at end of spin cycle. This spring maintains brake tension so the basket stops promptly. DIY repair takes about 1 hour.
I replaced the: brake stator, rotor, and snubber ring. I did need to remove the stator which allowed the spring to decompress. I used 2 C-clamps to control the force when it was removed. To re-secure all the components I stood on the stator to compress the 200lbs spring until the screws could take the load safely. The entire thing took about an hour to slowly go through everything. Read more
Includes leg, foot pad and locknut.
1.) Made sure BOTH Hot & Cold Water Lines turned off to Maytag Washer. (I have dual shut-off valve for those two water lines), 2.) Briefly ran Washer on Warm Water Setting, removing water pressure & remaining water from Hot & Cold water lines. 3.) Unplugged Washing Machine. 4.) Used Needle Nose Pliers to remove BOTH Hot & Cold Water hoses from the hookup on the back of the washer. 3.) Made sure I had an empty bucket, on hand, to catch remaining water that may come out of now-removed, hot &... Read more