Jdb100aws Parts

This adjustable clip is used to hold the tines in place on a dishwasher rack. Color: blue. Measures about 3-3/4 inches wide by a 1/2 inch high.

This dishwasher drain hose channels wastewater from the pump to your home drain or air gap. Replacing a cracked, kinked, or clogged hose restores proper draining performance and helps prevent leaks or water backing into the tub. What it does:

• Routes wastewater from the dishwasher to the household drain or air gap
• A damaged, kinked, or blocked hose can cause slow/no drain, standing water, or leaks
• Visible splits, soft spots, or persistent odors/backflow are common signs the hose should be replaced
• Restores reliable draining and helps protect surrounding cabinets and flooring from water damage

• 1 drain hose

• Disconnect power and shut off water before servicing
• Pull the dishwasher forward and place a towel or pan to catch residual water
• Match the original routing and maintain a proper high loop or air gap per local code to prevent backflow
• Secure connections with clamps, ensure the hose isn't kinked, and run a test cycle to check for leaks

Used on the end of the rails to prevent the upper rack from falling out.

This Tub Edge Trim (bottom) fits along the lower edge of the dishwasher tub opening. Replacing a cracked, warped, or missing trim restores a clean finished edge and helps the door open and close smoothly without rubbing or snagging.

• Finishes and protects the bottom lip of the tub opening
• Helps maintain proper clearance for the door panel and gasket
• Replaces damaged, warped, discolored, or missing trim
• Typical symptoms: loose or broken strip, rubbing when closing, visible gap along the lower edge

• Disconnect power to the dishwasher before servicing
• Open the door and remove the old trim by releasing its retaining tabs or screws; note orientation
• Align the new trim on the lower tub edge and press or fasten until fully seated across the opening
• Verify the door closes freely and the gasket seats evenly before restoring power

This lower dishwasher rack fold away row tine can be used for both the left and right hand side. Color: light gray. Measures about 3-1/2 inches high by 10 inches deep.

This top wash arm retainer secures the dishwasher's upper spray arm so it spins freely and stays aligned, helping maintain proper water distribution for upper-rack cleaning. Replace a cracked or worn retainer to reduce wobble and misalignment. What it does:

• Holds the upper/ top spray arm in place on the spray assembly so the arm can rotate correctly.
• Prevents the spray arm from slipping or wobbling during the wash cycle.
• Helps restore proper water spray coverage to the upper rack when the original retainer is broken or worn.
• Compatible with standard upper spray arm mounting—no modification required.

• Includes: 1 top wash arm retainer

• Disconnect power to the appliance before beginning any repair.
• You may need to remove the upper rack and/or the spray arm to access the retainer; keep parts organized for reassembly.
• Inspect the spray arm and attachment for damage or debris while replacing the retainer.
• Use hand tools only.

The Tub Wheel supports and guides the washer's tub assembly on its base during wash and spin cycles. Replacing a worn wheel restores smoother, quieter operation and helps reduce vibration and rubbing as the machine operates.

• Provides rolling support so the tub can move and self-balance during cycles
• Reduces friction between the tub and the base/frame
• Helps keep the tub centered to minimize noise and vibration
• Failure symptoms include squeaking or grinding, scraping noises, dragging movement, or visible flat spots/cracks on the wheel

• Disconnect power and water supply before servicing; wear appropriate gloves and eye protection
• Access the base/suspension per the service information and support the tub to remove load from the wheel
• Remove the retainer/axle, install the new wheel, and free rotation and correct orientation
• Reassemble, level the appliance, and run a spin test to check for noise and balance

Screw: 8-16 x 3/8 inch.

Color: light blue. Measures about 6 inches wide by a 1/2 inch high.

Specs: No.8X1/2 HEX WASHER HEAD

Replacement rinse aid dispenser knob restores a simple, reliable way to set and dispense rinse aid in the dishwasher. It gives a clear tactile control for adjusting rinse aid release so dishes dry and rinse with fewer spots. What it does:

• Replaces a cracked, stripped, missing, or hard-to-turn rinse aid control knob
• Allows you to set the dispenser level or open/close the rinse aid dosing mechanism
• Helps resolve problems where the knob won't turn or is detached from the dispenser
• Matches the original dispenser interface for correct fit and operation

• Always disconnect power to the appliance before servicing (unplug or switch off the breaker)
• Access the rinse aid dispenser per the dishwasher service manual or OEM instructions
• Align the knob on the dispenser post and press/snap it into place; avoid forcing or overtightening

Small replacement screw that secures panels and internal components on compatible appliances. Restores proper fastening to reduce rattling and loose parts so controls and panels stay aligned during normal use. What it does:

• Secures panels, brackets, and small components to the appliance frame or assemblies.
• Helps stop rattling, vibration-related noise, and movement from loose parts.
• Replaces a missing, worn, or stripped fastener to restore proper mounting.
• Used wherever the original manufacturer specified this screw in service diagrams.

• Disconnect power and water before working on the appliance to avoid shock or injury.
• Match the replacement screw to the original by fit and thread before installation; do not force mismatched fasteners.
• Start the screw by hand to avoid cross-threading; tighten securely but avoid over-torquing which can strip threads or damage components.
• Refer to the appliance's service manual or parts diagram for exact location and any torque or threadlocker recommendations.

The Cabinet Mount Bracket secures a built-in appliance to the surrounding cabinetry. Replacing a bent or missing bracket restores a tight, rattle-free installation so the unit stays level and aligned during everyday use.

• Anchors the appliance to the cabinet or side walls to prevent shifting or tip-out
• Maintains flush, level alignment with adjacent cabinets and countertop
• Helps reduce vibration and rattling noises during operation
• Replace if the original bracket is bent, cracked, corroded, or missing

• Disconnect power and any utilities before starting work.
• Support the appliance and pull it forward enough to access the mounting area.
• Reuse manufacturer-specified screws or approved replacements; tighten securely without overtightening.
• Secure both sides as originally configured and test operation.

This left corner trim restores the finished edge on a refrigerator door or cabinet frame, improving appearance and helping protect the gasket area from damage. It's a direct-fit plastic trim piece used where the door meets the cabinet. What it does:

• Covers and protects the door/frame corner to prevent chipping and wear
• Helps maintain a smooth seal surface by securing the gasket edge
• Reduces visible gaps or rough edges that cause cosmetic issues
• Commonly replaced when cracked, broken, or missing after impact or wear

• One left corner trim piece

• Unplug the appliance or disconnect power before beginning work when applicable
• Remove any adjacent trim or fasteners gently to access the mounting area
• Align the trim with the corner and press or fasten per the OEM attachment points
• Avoid forcing the piece; inspect surrounding gasket and mounting clips and replace if damaged

This fold-away tin latch secures the appliance door/panel and restores proper closure, helping the unit start and run normally. It's a small replacement part that fixes common latch and door-sealing issues. What it does:

• Holds the door or access panel closed so the appliance can complete cycles
• Replaces a bent, broken or non-retracting fold-away latch
• Helps resolve symptoms like a door that won't stay closed or a unit that won't start because the latch won't engage
• Durable tin construction for reliable, long-term operation

• Turn off power (unplug appliance or switch off breaker) before starting repair
• Remove only the exterior panel(s) required to access the latch; keep track of fasteners
• Inspect mating strike and surrounding parts for damage; replace if worn

The fold-away tine latch secures the flip-down tines on your dishwasher rack. It locks tines upright to support dishes and releases to fold them flat, restoring rack flexibility and preventing tines from collapsing during cycles.

• Locks fold-away tines in the up position to support dishes and glassware
• Releases to allow tines to fold flat for larger items
• Helps maintain stable, organized loading during wash cycles
• Common symptoms: tines won't stay upright, latch won't click/hold, missing or broken latch

• Open the dishwasher door and remove the affected rack for access
• Note the latch orientation; release the old latch from the tine assembly
• Snap the new latch into place until it engages
• A small flat-blade screwdriver can help release locking tabs