Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Routes wastewater from your dishwasher pump to the home drain. Replace if cracked, kinked, punctured, or worn to restore proper drainage and prevent leaks.
Replaced the seal at the Air/Water inlet and also replaced the drain hose. Drain hose had a worn spot due to vibration rubbing on the floor Read more
Trim piece that finishes the lower edge of the dishwasher tub opening. Replace if cracked, warped, or missing to restore a clean edge and smooth door operation.
I ordered a new rubber door seal for around door, new bottom door seal and spinner impeller and nut to hold on bottom arm as it looked weak. Everything worked great except bottom door seal which looks slightly different and would NOT stay on. I ended up putting back on the old one. Door doesnt leak but not sure it would even be worth it sending part back as I already tossed bag out. Other parts worked great and DW cleaning better. Read more
Screw: 8-16 x 3/8 inch.
Specs: No.8X1/2 HEX WASHER HEAD
Replaced the control board after removing the inner door liner, plastice board cover and board itself, by removing screws, working various plastic clips/tabs and unclipping wire harnesses from board. most of time was spent cleaning the black soot from the door, which had a terrible burnt electrical/plastic fire smell. Cleaned mold/scale off of as much of the door as I could while in there as well. Removing parts without breaking plastic tabs to hold the new parts was trickiest part. Read more
Secures the upper spray arm so it spins freely and stays aligned. Replace if cracked, worn, or causing wobble to restore proper water distribution.
Spun each of the three wash arms by hand. All could be made to touch/scrape but the top one was super wabbly. Ordered both the arm and clip. Repair took less than a minute. Used a screwdriver to pry loose one side of the old clip to remove. Aligned the new parts and easily snapped into place. Read more
Left side dishrack adjuster assembly with integrated roller wheels. Replaces broken, cracked, or worn adjusters when wheels split or break off the track.
I ordered the replacement part from AppliancePartsPros after speaking with a representative for several minutes. He was very helpful and patient and I order the exact part I needed. Read more
Replace the cable bracket guide roller on your dishwasher. This small wheel guides the door cable smoothly through the bracket, preventing binding and wear.
Secures your dishwasher to surrounding cabinetry. Replace this bracket if it's bent, broken, or missing to restore a tight, level installation.
Followed video instructions Read more
Replace your dishwasher's left corner trim to restore the door edge finish and protect the gasket area. Verify fit with your model number before ordering.
This fold-away tin latch secures the appliance door/panel and restores proper closure, helping the unit start and run normally. It's a small replacement part that fixes common latch and door-sealing issues. What it does:
Ordered the parts which were received promptly. My wife and I tried to install some without much luck. Our adult daughter came for Thanksgiving and installed them perfectly in minutes. It's tough to get old. Very satisfied with service and would use again if needed. Read more
Replacement leveling leg that stabilizes and adjusts your dishwasher height for proper alignment. Needed when bent, broken, or missing to eliminate rocking.
Secures flip-down tines on your dishwasher rack in upright position. Replace if latch is cracked, broken, or missing to restore tine flexibility.
Replaced the Fold away tine latch that had broken after 10 years of use. Read more
Gray plastic pivot that secures fold-down tines on your dishwasher rack. Replace broken, cracked, or missing pivots to restore tine adjustability.
Ordered part. Arrived quickly. Replaced part. All works well! Read more
This flexible injector hose routes liquid between the appliance's injector/dispenser and the pump or spray assembly, restoring proper dispensing and preventing leaks. It's a direct-replacement service part for affected injector connections. What it does
Simply chatted online with AppliancePartsPros.com who sent a link to order. Part arrived quickly. Also noticed a hose kinked and they showed me how to assemble it too. Read more
Ball bearing for dishwasher upper rack track. Replace when rack slides roughly or makes noise. Restores smooth gliding. Verify fit by model number.
I determined the parts needed from disassembling the carriage and called the help line to ensure I ordered the correct parts for my model number. They were very helpful in ensuring I ordered the correct part and that is shipped promptly. I would definitely use them again (and I have 3 times now!) Read more
Dark gray stop rail secures the dishwasher rack slider and prevents the rack from sliding out. Replaces worn, cracked, or missing rail caps on the track.
It was really annoying- every once in a while the entire slider would come out and the top drawer would fall! The fix was easy once I saw on your site the diagram that showed the end cap. It was easy to replace, the dishwasher is now fixed and everyone is happy! Read more