Jdb3610bx Parts

This is the shorter of the two dispenser lid hinge pins. For the longer lid hinge pin order WP6-912678.

This door switch detects when the dishwasher door is fully closed and latched. Replacing a worn or intermittent switch restores reliable start/stop operation and ensures the safety interlock cuts power whenever the door is opened.

• Senses door-closed status and sends a signal to the control
• Interrupts power to the machine when the door opens
• Helps prevent operation with an unlatched door
• Typical failure symptoms: won't start, stops mid-cycle if the door is bumped, or only runs when pressing on the door

• Disconnect power at the breaker before servicing
• Access the latch/switch area by removing the inner door panel or console; note wire locations
• Transfer wires one at a time and secure the new switch in the bracket
• Verify latch engagement and switch actuation before restoring power

This rack stop clips onto the end of a dishwasher rack rail to keep the rack from sliding off the track. Replacing a worn or missing stop helps the rack glide securely and prevents accidental pull-outs during use.

• Prevents the rack from being pulled out too far and falling off the rail
• Helps restore smooth, secure rack operation
• Common fix for racks that slide out too far or feel unstable

• Disconnect power and turn off water before servicing
• Pull the rack forward, depress the old stop's locking tab, and remove
• Align and snap the new stop onto the rail end until it locks
• Check rack travel to ensure the stop is fully engaged

This small rubber grommet seals the opening around the dishwasher's detergent/rinse-aid dispenser, helping prevent leaks and moisture intrusion so the dispenser operates reliably throughout the wash cycle.

• Seals the dispenser passage to keep water from leaking into or out of the dispenser cavity
• Helps ensure proper detergent or rinse-aid dispensing
• Can reduce moisture-related corrosion or staining in the dispenser area

• Disconnect power and turn off water before servicing
• Remove inner door panel to access the dispenser assembly
• Note grommet orientation; seat fully to ensure a watertight seal
• Inspect surrounding surfaces for debris or damage before reassembly

This O-ring seal fits into a groove to create a tight, leak-resistant barrier where two parts join. Replacing a worn O-ring helps stop drips at connections and keeps your appliance running reliably. What it does:

• Forms a compressible seal between mating parts (fittings, housings, or tubing)
• Helps prevent water or fluid leaks at joints
• Maintains proper pressure and flow within the sealed path
• Replace if you see seepage at the connection or the ring is cracked, flattened, brittle, or swollen

• 1 O-ring seal

• Disconnect power and shut off water supply before servicing
• Clean the groove and mating surfaces; remove debris that could compromise the seal
• Lightly lubricate with manufacturer-approved silicone grease; avoid petroleum-based products
• Seat the O-ring without twisting; reassemble carefully and check for leaks after testing

Screw: 8-16 x 3/8 inch.

Specs: No.8X1/2 HEX WASHER HEAD

This switch holder secures a small appliance switch or actuator in the correct position so the control can detect and respond reliably. Replacing a cracked or broken holder restores consistent switch alignment and helps prevent intermittent operation. What it does:

• Holds the switch or actuator steady in the correct position for reliable electrical contact and activation
• Keeps the switch aligned so buttons, door/lid actions, or control functions register properly
• Common symptom: appliance function won't engage or is intermittent when the switch is loose or the holder is damaged
• Prevents further wear on the switch by keeping it from shifting or rubbing against surrounding parts

• Disconnect power (unplug or shut off breaker) before servicing the appliance
• Remove the control panel or access panel to reach the holder; keep small clips and screws organized
• Inspect the switch and actuator for damage while replacing the holder; replace any damaged mating parts

Small replacement screw that secures panels and internal components on compatible appliances. Restores proper fastening to reduce rattling and loose parts so controls and panels stay aligned during normal use. What it does:

• Secures panels, brackets, and small components to the appliance frame or assemblies.
• Helps stop rattling, vibration-related noise, and movement from loose parts.
• Replaces a missing, worn, or stripped fastener to restore proper mounting.
• Used wherever the original manufacturer specified this screw in service diagrams.

• Disconnect power and water before working on the appliance to avoid shock or injury.
• Match the replacement screw to the original by fit and thread before installation; do not force mismatched fasteners.
• Start the screw by hand to avoid cross-threading; tighten securely but avoid over-torquing which can strip threads or damage components.
• Refer to the appliance's service manual or parts diagram for exact location and any torque or threadlocker recommendations.

A replacement tension spring designed to restore proper movement and return force to the appliance mechanism. Helps the affected component operate smoothly so doors, levers or assemblies move with correct tension and alignment. What it does:

• Provides return and holding tension for the appliance mechanism to restore normal movement.
• Helps reduce sagging, misalignment, or loose operation of the associated door or linkage.
• Minimizes noise and vibration caused by a worn or weakened spring.
• Works as the direct-fit part when the listed part number matches your appliance.

• Disconnect power and water (if applicable) before beginning any repair.
• Springs are often under tension—wear eye protection and use caution when removing or installing.
• Follow the appliance's service manual or OEM instructions for correct orientation and safe installation.

A replacement leveling leg that stabilizes your appliance and allows height adjustment for a secure, level install. Restores proper alignment to reduce rocking, vibration and uneven door gaps. What it does:

• Raises and levels the appliance so all feet contact the floor evenly.
• Stops rocking and excessive vibration that can cause noise or wear.
• Helps restore proper drainage and door alignment by correcting tilt.
• Matches original fit and function for reliable support.

• Disconnect power (and water for appliances with plumbing) before servicing.
• Raise or support the appliance safely before removing or adjusting legs.
• Turn the leg to raise or lower; make small adjustments and recheck level.
• Use common hand tools (wrench or pliers) and avoid forcing damaged threads.

A small replacement retainer clip used to secure exterior trim and interior panels on compatible Whirlpool appliances. Restores proper panel fit and prevents rattling or loose trim for a cleaner, safer operation. What it does

• Secures trim, panels or components in place to maintain proper alignment
• Helps stop rattling, vibration noise and loose-fitting parts
• Keeps seals and covers positioned so doors and panels close correctly
• Simple, single-purpose hardware used where a clip-style fastener is required

• One retainer clip as pictured

• Disconnect power (and water if applicable) before starting any repair
• Remove the surrounding trim or panel to access the retainer; small trim tools may help
• Fasten clip into the OEM mounting hole until it snaps or seats firmly
• Keep removed screws and small parts organized to avoid lost hardware

This electric heating element generates the high heat needed for your appliance to reach operating temperatures, restoring normal heating performance and cycle effectiveness. Use the correct replacement for safe, reliable heat output. What it does:

• Heats the appliance's air or oven cavity so cycles reach intended temperatures
• Restores proper heating when the appliance runs but produces little or no heat
• Helps resolve long cycles or poor performance caused by a failed element
• Replaces a worn or open element that shows visible damage or electrical failure

• One heating element

• Disconnect all power before beginning service to avoid shock or injury
• Handle the element carefully to avoid bending or kinking the tubing/coil
• Verify electrical connections are secure and correct before restoring power

A replacement appliance door handle that restores a secure grip and proper operation to a worn or broken handle. Designed to match the original mounting style for a clean, factory-fit appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door smoothly
• Replaces cracked, loose, or broken handles that affect normal door use
• Restores correct alignment and leverage to reduce strain on door components
• Helps prevent accidental drops or slippage when grabbing the door

• One replacement handle

• Remove power and empty the door area before starting any repair
• Typical install requires removing trim or screws; use manufacturer-recommended fasteners
• Retain original mounting hardware unless the new handle explicitly includes replacements

This is a machine screw used to secure appliance panels and components where an 8-32 thread fastener is specified. It provides a reliable hold for control panels, brackets, and interior assemblies. What it does:

• Fastens panels, brackets, and small components to the appliance chassis
• Holds control assemblies and trim pieces in place
• Maintains secure connections that prevent vibration-related loosening
• Works where an 8-32 coarse-thread machine screw of short length is required

• One 8-32 x 3/8" machine screw

• Use the correct driver (Phillips or slotted) to avoid stripping the head
• Thread into metal or nut/insert; do not overtighten to prevent thread damage
• Disconnect power and remove any panels as required for safe access

This replacement rack track restores smooth, stable rack movement and keeps the oven rack aligned while sliding in and out. It helps prevent rack sagging, binding, or uneven travel so food and cookware stay level and secure. What it does

• Guides and supports the oven rack so it slides in and out smoothly.
• Prevents racks from sagging, tipping, or binding when pulled forward.
• Restores proper rack alignment to reduce scraping, catching, or loud banging.
• Works with standard oven/range racks that use a molded metal/plastic track system.

• High-level swap: remove the oven racks, unfasten the old track, and secure the replacement in the same mounting locations.
• Use appropriate hand tools and avoid forcing parts; aligning the track before tightening fasteners reduces binding.
• Disconnect power to the appliance or follow the manufacturer's safety guidance if servicing components near electrical connections.