Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
If your oven overheats or shows temperature errors, this temperature probe restores accurate heat sensing. Simple DIY fix in 15 minutes or less.
Common sense and following directions from a tech, Read more
Replacement control knob for your range cooktop. Installs on the control shaft to restore precise burner selection. Needed when original is cracked, broken, or missing.
Replaced the control panel. Read more
White porcelain touch-up paint for repairing chipped, scratched, or worn surfaces on ranges, ovens, and refrigerators. Restores appearance on exterior panels and trim. 2 oz. can.
Simply painted over worked great Read more
Sheet metal pan head screw secures panels, brackets, and components to appliance cabinets. Replace missing, stripped, or corroded screws to restore fit.
I ordered and replaced the old ignitor and the corroded mounting screws. Read more
Replacement fastening screw for securing trim, panels, and brackets inside appliances. Use when original screw is missing, stripped, or damaged.
I pulled out the old housing and unplugged the motor. It pretty much came out in pieces. Remove the plastic from the motor, then had to take a pair of vice grips to hold the spindle in place to remove the auger. Remove what was still attached to the old Housing. Cleaned everything up and put the whole unit back together. The motor looked like it was somewhat cooked but still worked, so I ordered a new motor and auger to replace it. Because this fridge is 24 yrs old, Appliancepartspros... Read more
This is the blower motor used in the downdraft ventilation system of a range. It powers the fan that draws smoke, steam, and cooking odors down and away from the cooktop surface. Replace this motor if the downdraft vent makes unusual noises, vibrates excessively, runs intermittently, or fails to turn on at all.
Changed out motor Read more
Replaces a worn, cracked, or faded gas burner control knob on your range. Mounts on the valve stem to restore precise flame adjustment and clear markings.
White touch-up paint for covering minor scratches, chips, and blemishes on oven liners. Restores appearance of damaged oven interior surfaces.
Replace missing or stripped screws for your range anti-tip bracket. This 2-piece hardware set secures the bracket to the wall or floor for stability.
Fix burners that won't light or have intermittent ignition with this range burner igniter switch. Restores reliable spark function to gas cooktop burners.
13 oz. enamel spray paint in biscuit color for appliances. Restores scratched, chipped, or discolored surfaces on refrigerators, dishwashers, and more.
Purchased bisque spray paint. Product is "almost" a perfect match as color of refrig; was not as glossy but did the trick. Read more
Secures panels and assemblies inside your range or oven. Replace if the original snap nut is cracked, broken, or missing to keep internal components secure.
Fix a burner that won't stay lit or has a weak yellow flame. This venturi tube mixes air with gas for proper combustion. Easy 15-minute repair.
This is the second time I've had to replace the controls on my Jenn-Air stove. This time, 2018, last time 2011. Both times I ordered the part here and the part was exactly right. This time, having done it once before, it took me about 10 minutes. A few possibly useful tips: Control panel or circuit board? When the controls go on this stove, it could be due either to this keypad OR to the circuit board/controller board that sits behind the keypad. So you have to guess which one it is. ... Read more
Burner won't light or flame is uneven? The orifice holder secures the gas orifice for proper alignment and reliable ignition. Easy DIY repair in under 30 minutes.
I am a plumber by trade so I was guessing my way through this. It took me a while to figure out that I had to drill out the screws that held the burners in place. The screws were so rusted that I couldn't tell that they were philips. Then I found that I needed to pull the stove out about 5" and put 2x4s under the feet so I could get the screws that hold the top down. I ruined the orfice holders trying to drill out the old screws. I think my entire problem was caused by rust on the pan that the... Read more
Burner won't ignite or flame is weak? This top burner valve controls gas flow to individual burners. Common repair for ignition and flame issues.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.