Jgsp28 Parts

I have a Jennair jjw9630cas double wall oven, and after a few years I noticed that the light would not go out, first in the bottom oven, and then in the top oven. After doing some research I discovered this was not uncommon, and the fix usually involved replacing the hinges and/or the hinge receptacles. It didn't look like a difficult fix so I ordered four new hinges and four new receptacles, which arrived quickly. I found a video on YouTube that showed how to replace the hinges and it... Read more

• Oven is too hot
• Won't start
• Little to no heat when baking

My mother's GE range was not coming up to full heat (very far from it), and I was hearing a lot of relay-clicking coming from the control board. The heating elements seemed good. I suspected the control board was faulty, but there was a chance that it might be the (*much* less expensive) temperature sensor, so I ordered both from AppliancePartsPros.com (which got the parts to me very fast) so I could try the T-sensor first. After removing the doors and the back panel of the oven, and taking out... Read more

• Gas igniter glows, but will not light
• Won't start

After 5 igniter replacements, I've gotten pretty good at this. Less than 30 minutes start to finish -- including mopping under the range, etc. You need one hex driver for the whole job -- 3/8" I believe. 1. Remove all of the racks and the oven door. Remove the bottom panel inside the oven. Now unscrew the flame cover (4 hex screws), remove, and unscrew the old igniter (2 hex screws). 2. Pull the oven away from the wall. Be careful not to kink the gas line. Unplug the range. Remove... Read more

Orded rack by stove model number. fit perfect Read more

Cleaned/ soaked all burners in Ammonia and scraped off the remaining with a pumice stone. Oiled all screws. Replaced (4) ignitors or electrodes and module kit/ right front burner/ burner switch harness. Although this was the third order of switches from 3 different places including the local supplier due to the switches being manufactured upside down and lit on low on the first attempt. (Since I was going to have to open it up again to either repair or remove and return the upside-down harness... Read more

Replaced the glass assembly with parts ordered from appliancepartspros.com. Read more

Ordered replacement unit. It arrived as scheduled,even came with light bulb to my surprise. Turned off breaker, Removed two hex nuts, unplugged electrical connectors plugged in to new unit reinstalled hex nuts. Turned on breakers. Wife is happy. Read more

• Won't start

Took off old, replaced with new. Cross reference worked well, all GE parts. Saved a lot of money compared to local supplier. Read more

I pulled off the retaining clip with pliers then removed the old knob and timer dial. I replaced all the parts with the new ones and used pliers to reinstall the clip. The teeth on the new knob engage to select the cycle. https://www.youtube.com/watch?v=cQwLtRcHx9k Read more

I BOUGHT NEW BURNERS FRM YOU. EXCELLENT PRICE, SHIPPING ARRIVAL, PARTS WERE ORIGINAL GE PARTS. TY Read more

This job was fast. About 2 minutes. Just need to pull the old gasket out. Generally can be done with your hands but may need pliers if any of the metal wires get caught. Read more

I removed all the individual burners so I could lift the stainless cover to expose the igniter wires. I cleaned all the wire connections and the 4 good igniters and replaced the one bad igniter. Reassembly was easy and everything worked properly when done. Video of repair was helpful and all parts ordered were correct and shipped promptly and I will definitely use AppliancePartsPros again. Read more

So, in the process of a kitchen remodel my GC managed to lose *both* of the rear plastic supports for my GE stove! The drawer was totally unsupported without the brackets. I managed to find them on your site and see that they were a new and better design (rear mount with screw vs side mount and no firm mounting). The install was a snap and the brackets work excellent. I wish I knew that there was a new design years ago or I would have bought them much sooner! Thanks!! Read more

I was getting really frustrated with our oven. It would preheat to the correct temperature, then slowly lose heat until it was down to about 200 degrees. So it took about two hours to heat a pizza! Finally decided to repair the oven myself, rather than pay $300.00 to have a repair person come out. Ordered the replacement igniter from AppliancePartsPros.com, and it arrived in two days. I followed the instructional video on the AppliancePartsPros.com website, and it was going well until I... Read more

Fast delivery, great service Read more

Refer to Mynor T. of Draper, UT Aug. 12, 2018 write-up. I benefited greatly from the above write-up. It took me a little less time to perform this repair (excluding cleaning the assembly) due to the write-up. This GE Profile gas burner cook top is a “drop-in” model meant to be installed into counter top cut outs. The glass top edges are the actual support area for the entire cook top assembly. The burner bases (on top of the glass top) are screwed to the metal case enclosure (located beneath... Read more