Js670 Parts

A safety thermostat that stops the heater when internal temperatures get too high to protect the appliance and prevent overheating. Replaces a worn or failed high-limit switch to restore normal heater safety control. What it does:

• Monitors internal heat and opens the circuit if temperatures exceed safe limits
• Prevents continuous heating and reduces risk of overheating or fire
• Common symptom: dryer or oven heats erratically, overheats, or stops heating unexpectedly
• Works as a non-resettable safety cut-out in the appliance's vent or burner circuit

• Disconnect power (unplug appliance or switch off breaker) before servicing
• Handle terminals carefully; replace any damaged connectors and secure spade terminals fully

This blower assembly circulates air through the appliance to support drying and venting, restoring proper airflow for consistent performance. It replaces a worn or damaged fan wheel and housing to reduce overheating and poor drying. What it does:

• Moves air through the appliance to aid drying and ventilation
• Restores airflow lost from cracked, warped, or broken blower wheel
• Helps eliminate overheating, long-dry times, or reduced airflow
• Works with the motor and ducting to maintain proper exhaust flow

• One blower assembly

• Disconnect power before servicing to avoid shock or injury
• Inspect motor shaft and mounting before installing; replace any damaged hardware
• Ensure blower is oriented and secured per manufacturer alignment to prevent noise or imbalance
• Verify clear, unrestricted ducting after installation for proper performance

The Rear Vent Trim and Gasket Assembly is an OEM part for GE ranges. It seals the rear vent opening of the range, directing hot air and potential gas fumes outside through the exhaust vent during oven use. Without an intact seal provided by the gasket and vent trim, combustion byproducts can enter the kitchen presenting safety and performance issues.

Causes of a bad range rear vent assembly include wear over years of use with high heat cycles, cracking or degradation of sealing materials, or damage from cleaning or impacts around the vent area.

Symptoms of an issue include:

• Foul odors detected in the kitchen during use of the oven
• Inefficient or uneven baking and broiling
• Visible openings or gaps seen around the rear vent perimeter
• Detached, cracked, or missing components

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This replacement screw secures panels, brackets, and trim in your appliance. Using the correct #8-18 fastener helps restore a tight, rattle-free fit when replacing missing or damaged hardware. What it does:

• Fastens sheet-metal panels, brackets, and other components to the chassis
• Replaces missing, stripped, or damaged screws
• Helps eliminate vibration-induced rattles and looseness
• Maintains proper alignment of panels and assemblies

• 1 screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Align parts and start the screw by hand to avoid cross-threading
• Use an appropriate nut driver or screwdriver for the hex-washer head
• Tighten until snug; do not overtighten to prevent stripping

• Thread: #8-18 (type AB)
• Length: 3/8 in
• Head style: indented hex-washer

A silicon-controlled rectifier (SCR) used on appliance control boards to regulate power to motors, igniters or other loads. Replacing a faulty SCR can restore proper power switching and steady operation of the driven component. What it does:

• Acts as a power-switching semiconductor in appliance electronic control circuits to allow current flow only when triggered.
• Enables controlled delivery of voltage/current to motors, igniters and similar loads on the control board.
• A failing SCR can cause symptoms such as no power to a motor or igniter, intermittent operation, or complete failure of the driven component.
• Match the SCR package and electrical ratings to the control board before replacing.

• Disconnect all power to the appliance before accessing control electronics to avoid shock or damage.
• Take electrostatic-discharge (ESD) precautions; handle the SCR by its body and avoid touching leads.
• Package orientation and electrical ratings on the control board and wiring before installation.

This control panel assembly houses the user interface and display for the oven/range console, restoring readable displays and responsive buttons. Use it to replace a cracked, unresponsive, or malfunctioning front control console and regain normal oven control. What it does:

• Provides the button/touch interface and display for oven/range controls
• Replaces damaged or cracked console surfaces that block or misregister inputs
• Restores operation when buttons are sticky, unresponsive, or display is blank/intermittent
• Works as the main user interface for setting temperature, timers, and modes

• Disconnect power to the appliance at the breaker or unplug before starting.
• Handle the assembly carefully to avoid damaging the display, glass, or internal PCB and connectors.
• Use basic hand tools to remove the outer trim and mounting screws; support the panel while disconnecting wiring.

The Badge Assembly is an OEM part for GE ranges. It includes the magnetic decorative badge affixed to the front of the range. This badge displays important information such as the brand name, model number, and technical specifications.

Causes of a bad badge assembly can include damage from impacts or abrasions over time, adhesive failure from repeated heat exposure, or normal wear from routine cleaning. On a range, the badge must withstand higher cooking temperatures.

Symptoms of a bad badge assembly include:

• Faded or illegible print on the badge face
• Cracks or breaks in the plastic material
• The badge lifting or peeling away from the surface
• Missing or loose attachment clips/fasteners

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This stainless-steel drawer panel replaces a damaged or worn front on compatible refrigerator freezer drawers to restore appearance and provide a secure, functional drawer face. It's a direct-fit exterior panel that refreshes the appliance's look. What it does:

• Replaces dented, scratched, or corroded drawer front panels to improve appearance
• Restores a flush, secure drawer face for proper opening and closing
• Matches stainless-steel finish for a consistent exterior look
• Helps protect underlying drawer components from damage and moisture

• Disconnect power to the appliance before beginning any repair
• Remove the drawer per manufacturer instructions to access mounting fasteners
• Handle the panel carefully; edges may be sharp and protective film should be removed after installation
• Use appropriate tools and follow OEM instructions

Size: 8-18 BA POR 3/4 SN

This is a replacement M4 hex nut used to secure small appliance panels, brackets, and assemblies. It provides a simple, reliable fastening point to restore proper fit and reduce rattles or loose parts. What it does:

• Secures panels, brackets, fasteners and small components in appliances
• Replaces missing or damaged nuts that allow parts to shift or rattle
• Restores proper thread engagement for M4-0.7 machine screws
• Helps maintain alignment of mounted assemblies when tightened correctly

• Turn off and unplug the appliance and remove power source before starting work
• Hand-start the nut to avoid cross-threading, then tighten snugly with the correct wrench; do not overtighten
• Replace any fasteners with damaged threads or stripped heads for a secure repair

This replacement screw is a simple fastener used to secure panels, trim, and internal components on GE appliances, restoring proper fit and preventing loose parts. It's a direct-replacement hardware piece for common mounting and assembly points. What it does

• Secures panels, brackets, and trim to prevent rattling or gaps
• Replaces missing, stripped, or corroded fasteners that compromise fit
• Helps maintain proper alignment of controls and components
• Keeps internal parts fixed for safe, reliable operation

• Screw as shown

• Unplug or disconnect power to the appliance before starting repairs
• Use the correct screwdriver or bit to avoid stripping the head
• Install with moderate torque; do not overtighten to prevent thread or component damage
• If threads are damaged or the mating hole is stripped, replace the mating hardware or repair the thread before reuse

This panel overlay assembly replaces a worn or damaged control-panel face to restore button labels and the finished appearance of the range or oven. It provides a clean, readable surface for the control buttons and display. What it does:

• Replaces cracked, peeled, or faded control-panel graphics and labels
• Restores a uniform finish so controls and settings are easy to read
• Supports proper button alignment so user inputs engage correctly
• Helps prevent dirt and moisture from reaching underlying electronics

• One panel overlay assembly

• Disconnect power (unplug or shut off breaker) before starting any repair
• Handle glass, trim, and fasteners carefully to avoid scratching or chipping
• May require removal of the backguard or control bezel and basic hand tools

The GE Range Maintop Glass Assembly is an OEM component specifically designed for GE electric ranges. It consists of tempered glass precisely cut and treated to withstand high heat. This assembly serves as the durable cooking surface of the range.

Symptoms of a bad maintop glass assembly include:

• Improper heating or hot or cool spots on the glass surface
• Glare or visibility issues looking through the glass  
• The glass making popping or cracking sounds during heating
• Difficulty keeping the surface clean despite regular cleaning

Causes of failure can be fatigue from repeated heating and cooling cycles, accidents like dropped cookware, or flaws in the glass. Over time, everyday use puts stress on the material that will eventually cause damage.

This genuine OEM GE part is compatible with Hotpoint, RCA and select Kenmore ranges. 

This replacement control panel overlay restores the printed labels and clean appearance of your appliance's control console. It helps ensure settings and buttons are easy to see and read again for everyday operation.

• Provides the graphic legends and markings for the control panel
• Fits over the console to present a factory look and proper button alignment
• Helps address faded, peeling, bubbled, or cracked graphics
• Can improve visibility of controls when original markings are worn

• Disconnect power to the appliance before servicing
• Follow your model's service information to access the control panel and remove the old overlay
• Handle by the edges to avoid damage to the printed surface
• Carefully align with openings and edges before final placement

This pilot indicator light mounts in the control panel and illuminates to show when a heating circuit is active. Replace a failed or damaged pilot light to restore a clear "on" reminder and improve everyday visibility around hot surfaces.

• Provides a visual "ON" signal when the corresponding control is turned on
• Common symptoms: indicator won't light, is dim or flickers, or the lens/housing is damaged
• Restores a clear status cue to help you see when heat is active
• Direct replacement for the original pilot light assembly

• Disconnect power at the breaker before servicing
• Remove back cover or control panel trim to access the light
• Note wire positions and transfer them to the new light one at a time
• Seat the light securely in the panel opening, reassemble, and test

Outer stainless-steel door panel that replaces a damaged or dented exterior door surface to restore appearance and protect internal components. Designed to match stainless finishes and return a clean exterior to the refrigerator. What it does:

• Serves as the outer skin of the refrigerator door, protecting insulation and internal parts from everyday wear.
• Replaces dented, scratched or corroded exterior panels to improve appearance.
• Provides the proper exterior surface for mounting handles and trim.
• Helps maintain an even exterior surface that supports door alignment and cosmetic finish.

• Disconnect power to the appliance and remove food and removable door items before beginning work.
• Door panels are large and may be heavy — use a helper and proper lifting technique to avoid injury or damage.
• Installation may require removing handles, trim, and the inner liner; follow the OEM service instructions for your model.