Js760epes Parts

Fix a broken or loose oven door handle that won't grip properly. This assembly restores secure operation and smooth door closing for your electric range.

Stainless infinite control knob for electric ranges. Replaces worn, cracked, or missing knobs on burner controls. Restores smooth heat selection.

Replace your worn oven door gasket to restore heat-resistant seal, improve temperature control, and reduce heat escape. Confirm fit with your model number.

Aligns and stabilizes your range's lower storage or warming drawer for smooth sliding and flush closure. Replace if cracked, worn, or missing to restore fit.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

Replace a missing, bent, or corroded oven rack in your electric range. This rack slides on side rails to support bakeware and cookware at the correct level.

Replaces a worn, cracked, or damaged range door handle and end cap. Restores a clean, finished look and secure grip for smooth door operation.

Range overheating or won't turn on? This high limit safety thermostat monitors internal temperature and cuts power to prevent damage. Restores safety.

This control and faceplate assembly replaces a failed oven control so you can restore temperature control and user interface functions. It mounts on the oven front and provides the touch/selector surface and control electronics. What it does:

• Houses the oven's electronic control board and user interface for setting bake, broil, timers and other oven functions
• Re-establishes responsive keys/buttons and on-screen displays when the original faceplate is cracked or controls stop responding
• Helps resolve intermittent heating, unresponsive buttons, or display errors tied to a damaged control panel
• Works as the oven's primary command and status interface for cycle selection and feedback

• One control and faceplate assembly

• Disconnect power at the breaker before servicing to avoid electrical shock
• Handle the display and ribbon/connector areas carefully; avoid bending or damaging harnesses
• Some installations require removing the oven control housing and connectors—refer to factory service instructions

Fix a loose or misaligned cooktop with this maintop strike plate. Restores secure engagement between the cooktop and latch mechanism. Simple repair.

The Rear Vent Trim and Gasket Assembly is an OEM part for GE ranges. It seals the rear vent opening of the range, directing hot air and potential gas fumes outside through the exhaust vent during oven use. Without an intact seal provided by the gasket and vent trim, combustion byproducts can enter the kitchen presenting safety and performance issues.

Causes of a bad range rear vent assembly include wear over years of use with high heat cycles, cracking or degradation of sealing materials, or damage from cleaning or impacts around the vent area.

Symptoms of an issue include:

• Foul odors detected in the kitchen during use of the oven
• Inefficient or uneven baking and broiling
• Visible openings or gaps seen around the rear vent perimeter
• Detached, cracked, or missing components

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replacement mounting spacer for electric ranges. Positions and supports panels to maintain alignment and proper fit. Replaces worn, missing, or damaged spacers.

Lost remote monitoring or app control? This Wi-Fi communication board restores wireless connectivity so you can monitor and control your appliance remotely.

Fix unresponsive buttons or blank displays with this electric range control and faceplate assembly. Restores all oven functions and timer settings.

This flat washer (.250 inch inner diameter x .812 inch outer diameter) is a simple replacement part that helps distribute load from a fastener and protects mating surfaces for reliable appliance operation. What it does:

• Provides a stable bearing surface for screws, bolts or studs to reduce wear on parts
• Helps distribute clamping force to prevent pull-through or deformation of softer materials
• Reduces vibration and movement at the joint when installed correctly
• Missing or damaged washers can lead to loose fasteners, increased vibration or component misalignment

• Disconnect power and water before servicing the appliance
• Replace like-for-like: inner/outer diameters and thickness match the original washer
• Inspect mating hardware and surfaces for damage; replace corroded or deformed fasteners as needed
• Tighten fasteners evenly and avoid over-torquing to prevent washer or component damage