Jvm6175e Parts

This rivet assembly is a direct-replacement fastening piece used to secure appliance panels and components, restoring a stable, rattle-free fit and preventing movement caused by worn or broken rivets. What it does:

• Secures panels, brackets, or component mounts to restore proper alignment and support
• Stops rattling, vibration, or loose hardware caused by damaged or missing rivets
• Provides a durable mechanical fastener where original rivets have sheared or loosened
• Helps maintain safe operation by keeping parts properly retained

• Disconnect power (and gas/water if applicable) before attempting any repairs
• Removal may require drilling out the old rivet; installation typically needs a rivet gun or equivalent tool
• Keep hardware orientation the same as the original; replace any damaged surrounding parts

Magnetron with thermal fuse.

This resin canopy is the interior ceiling cover inside the microwave cavity. It shields the stirrer area from grease and splatter to help maintain even heating and protect internal components for safer, more reliable cooking. What it does:

• Covers and protects the stirrer/waveguide opening at the top of the cavity
• Helps promote even microwave energy distribution for consistent cooking
• Shields internal parts from grease, steam, and food debris
• Replace if warped, cracked, burned, discolored, loose, or if you notice arcing/sparking inside the cavity

• 1 resin canopy

• Disconnect power before servicing; microwave components can carry high voltage
• Remove the old canopy by releasing tabs or fasteners from inside the cavity
• Clean the cavity roof and seating surfaces before installation
• Ensure the canopy is fully seated and do not operate the microwave without it installed

This fuse assembly is a safety component that opens the circuit when an overcurrent or short occurs, protecting the appliance's wiring and electronics. Replacing a blown fuse assembly can restore power once the underlying fault has been corrected. What it does:

• Provides overcurrent protection by interrupting power during a fault
• Helps with symptoms such as a completely dead unit, dark display/control panel, stopping mid-cycle, or repeatedly blown fuses
• Protects internal wiring and control components from damage
• Designed to fail safely to prevent further electrical issues

• 1 fuse assembly

• Disconnect power to the appliance before servicing; if hardwired, switch off the circuit breaker
• Replace only with the correct fuse type/rating specified for your model
• Identify and correct the root cause of the blown fuse (e.g., shorted wiring or component) to avoid repeat failure

This replacement plate restores the original support and fit for the appliance component it secures, helping stop rattles and misalignment. Use this OEM-design plate when the original is bent, cracked, or missing. What it does:

• Provides a stable mounting surface to secure adjacent parts and assemblies
• Prevents movement that can cause noise, misalignment, or uneven operation
• Restores correct spacing and alignment for panels or elements
• Helps maintain safe, consistent appliance performance when damaged

• One plate

• Disconnect power (unplug or switch off breaker) before starting any repair
• Handle edges carefully; replacement metal parts can have sharp edges
• Verify orientation and alignment before tightening fasteners; use only the hardware specified by the manufacturer

This Cover-Stirrer protects the microwave's stirrer assembly and helps direct microwave energy for more even cooking. It's a direct-replacement plastic cover that restores proper operation and prevents debris from reaching the stirrer. What it does:

• Shields the stirrer/fan area from food splatter and debris to prevent damage.
• Helps maintain proper microwave energy distribution so food heats more evenly.
• Prevents contact with moving stirrer components for safer operation.
• A cracked or missing cover can lead to uneven heating, noise, or arcing.

• One Cover-Stirrer

• Disconnect power to the appliance before servicing.
• Remove the microwave's inner components or cavity access panels to reach the stirrer area.
• Align and seat the cover securely over the stirrer assembly; do not force or overtighten.
• If the existing cover is damaged, replace it; inspect surrounding components for damage or wear.

This body latch assembly secures the appliance door during operation, restoring proper door closure and allowing cycles to start and run safely. It replaces a worn or broken latch to improve sealing and reliable door engagement. What it does:

• Physically latches the door to keep it closed during operation
• Prevents the appliance from starting when the door is not fully engaged
• Resolves symptoms like a door that won't stay closed, cycles that won't start, or intermittent door-sense errors
• Replaces worn, cracked, or damaged latch components that impair engagement

• Disconnect power (and gas, if applicable) before beginning any repair
• Remove outer door or access panel per OEM instructions to reach and replace the latch
• Handle plastic latch components carefully to avoid cracking; test door engagement before reassembling panels

This run capacitor helps the appliance motor start and run smoothly by storing and releasing electrical energy. Replacing a worn capacitor can restore reliable motor operation and reduce abnormal motor noise or cycling. What it does:

• Provides the brief power boost motors need to start and maintain RPM
• Helps stabilize motor voltage and improve run efficiency under load
• Commonly linked to symptoms such as motors that hum but won't start, slow or intermittent motor operation, or unusual motor noise
• Reduces stress on motor windings that can lead to premature failure when functioning properly

• One motor capacitor

• Always disconnect power at the breaker or unplug the appliance before servicing
• Capacitors can hold a charge; discharge safely
• Observe proper polarity and mounting location during installation; secure wiring and connectors

This wire rack spacer replaces a damaged or missing spacer on an oven rack to keep wires properly separated and racks aligned for smooth sliding and stable support. It helps restore correct rack spacing and prevents metal-on-metal contact. What it does:

• Keeps adjacent rack wires separated to prevent rubbing, scratching, and unwanted contact
• Stabilizes oven racks so cookware slides in and out more smoothly
• Helps maintain even rack spacing for safer, more consistent placement of pans
• Simple replacement for worn or broken plastic/insulating spacers on wire racks

• Allow the appliance to cool and remove the rack before starting
• Slide or clip the spacer onto the rack wire in the original position; most installs are tool-free
• Inspect surrounding spacers and replace any that are cracked or missing to maintain even support

This LED module replaces the interior refrigerator light assembly to restore proper illumination inside the fresh food compartment. It provides a direct swap for failed or dim LED lighting to help you see food clearly. What it does:

• Replaces the refrigerator's interior LED light assembly to restore full, even cabinet illumination
• Commonly used when the light is dim, flickering, or completely out
• Connects to the existing lighting housing and wiring harness for a straightforward replacement
• Designed to match OEM fit and function for compatible refrigerator models

• One LED module

• Disconnect power to the appliance before starting any repairs to prevent shock
• Remove the light cover or housing per your model's instructions to access the module
• Handle the module and LEDs carefully; avoid touching LEDs or circuitry directly

A replacement control panel cover that restores the appliance's front console appearance and protects the underlying control assembly from spills and debris. Fits the OEM panel opening for a clean, factory look. What it does:

• Covers and protects the control console assembly from moisture, grease and everyday wear
• Keeps buttons, switches and display areas free from debris that can interfere with operation
• Restores the appliance's exterior appearance after damage or wear to the original trim
• Helps maintain proper airflow and spacing around control components

• One control panel cover (trim piece) as shown

• Designed for a direct fit; install with basic hand tools — disconnect power before starting
• Handle gently to avoid scratching the finish; align mounting tabs before securing
• Replace missing or damaged screws or clips with OEM-specified fasteners

This grille assembly replaces a damaged or worn front trim piece to restore the appliance's finished appearance and proper fit of the control area. It provides a like-for-like exterior trim replacement for affected ranges or ovens. What it does:

• Covers and protects the front control area and internal components behind the trim
• Restores a clean, finished look when the original grille is dented, cracked, or scratched
• Helps maintain proper alignment of the control panel and adjacent trim pieces
• Stops drafts or visible gaps that can occur when the grille is bent or loose

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Handle edges carefully; metal trim can have sharp edges.
• Installation typically requires removing adjacent trim or fasteners and aligning the grille before securing with screws or clips.