K45ssdwh Parts

This pivot screw secures a hinge, lever, or linkage to its bracket to create a stable pivot point. Replacing a missing or stripped screw restores proper alignment and smooth movement of the assembly.

• Fastens a pivoting component to its mounting point
• Maintains alignment and smooth, controlled motion at the pivot
• Helps prevent looseness, wobble, or sag at the joint
• Common symptoms include a missing/loose screw, binding movement, rattling, or uneven gaps

• Disconnect power; shut off gas/water if applicable before servicing
• Support the hinged or moving component to remove load from the pivot
• Remove the damaged screw and start the new screw by hand to avoid cross-threading
• Tighten snugly without over-torquing; replace companion bushings or washers if worn

This helical spring lock washer secures machine screws and bolts in your appliance, maintaining clamping force under vibration and thermal cycling. Use it to keep fasteners tight and assemblies stable for reliable operation.

• Provides spring tension to resist loosening from vibration and movement
• Helps maintain secure mounting and alignment of brackets, motors, and panels
• Common symptoms of a missing or fatigued washer: screws backing out, rattling/vibration noises, or a loose fit after tightening

• Unplug the appliance; shut off water supply if applicable
• Install between the fastener head (or nut) and the mating surface
• Use a matching screw size; replace any stripped or corroded hardware
• Tighten snugly without over-tightening

This trim band replaces damaged or missing outer oven door trim to restore a clean, finished appearance. It's a cosmetic, direct-replacement piece that covers the door edge and conceals the mounting gap. What it does:

• Restores the oven's exterior finish by replacing scratched, dented, or bent trim.
• Covers exposed edges and mounting seams for a seamless look.
• Helps prevent buildup of grime where trim is missing or separated.
• Stops minor rattling or movement caused by loose or damaged trim.

• Disconnect power to the appliance before starting any repair.
• Handle edges and nearby glass with care; wear cut-resistant gloves.
• Installation may require removing the oven door or control panel to access mounting clips—verify fit and alignment before final fastening.

This latch secures the appliance door and helps ensure a proper close for normal operation. It replaces a worn or broken latch to restore reliable door engagement and user safety. What it does:

• Holds the door closed so the appliance can operate as intended
• Replaces a damaged or broken latch that prevents the door from staying shut
• Helps restore proper alignment and engagement of the door mechanism
• Can reduce door rattling or intermittent closing issues

• Latch

• Disconnect power (and gas, if applicable) before starting any repair
• Remove the door or access panel to reach the latch per your model's service instructions
• Compare the new latch to the old part for correct orientation before installation
• Test the door operation after installation to ensure secure engagement

This replacement sleeve slips over the appliance shaft to protect mating parts from wear and help restore smooth, quiet operation. It's a simple wear item that prevents metal-on-metal contact and reduces rubbing noise. What it does:

• Protects the shaft or mating surface from wear and abrasion.
• Restores proper fit between rotating parts to reduce noise and vibration.
• Helps stop squeaking, rubbing, or rough rotation that can develop with worn components.
• Extends the service life of adjoining bearings, seals, or bushings when installed correctly.

• Disconnect power and water before starting and pull the appliance away from walls.
• Access may require removing panels or the adjoining component; basic hand tools are typically needed.
• Inspect mating surfaces and replace any damaged bearings, seals, or fasteners for a lasting repair.

This flat washer provides a durable spacer and load-distribution surface for fasteners in laundry appliances, helping secure components and reduce wear. It's a simple replacement that restores proper fastening and alignment where a worn washer is causing issues. This is for 1 washer, the photo is an example of the washer.  

What it does:

• Distributes nut/bolt pressure to protect mounting surfaces and prevent loosening
• Maintains correct spacing and alignment of panels, brackets, or moving parts
• Helps reduce vibration-related noise and abrasion at fastener points
• Common symptom: loose or rattling panels or hardware where a washer has deteriorated

What's included:

• One flat washer

Install notes:

• Turn off power and unplug the appliance before accessing panels or hardware
• Remove the fastener, replace the old washer with the new one, and re-torque to the OEM-recommended specification
• Inspect surrounding hardware and replace any damaged screws or nuts for a secure repair

Size: 6-32 x 9/32 inch.

This insert is a small, model-specific fitting that seats inside its assembly to align and secure the mating component. Replacing a cracked or missing insert restores a tight fit, correct positioning, and smooth operation.

• Provides the alignment/seating interface within the related assembly
• Helps the attached part fasten and sit properly
• Restores correct spacing and positioning for smooth operation
• Symptoms include a missing/broken insert, loose or wobbly component, difficulty securing or closing, or visible gap/misalignment

• Unplug the appliance and shut off water/gas before service
• Refer to your model's parts diagram for exact placement and orientation
• Transfer/reuse any original screws, clips, or fasteners as required
• Do not overtighten; confirm alignment and test operation afterward

This replacement screw is a direct-fit fastener used to secure appliance panels and components, restoring proper fit and reducing movement. Ideal when original screws are stripped, missing, or damaged. What it does:

• Secures panels, trim, brackets, and other serviceable components to prevent rattling or misalignment
• Matches original fastener form for correct fit and reliable function
• Helps restore proper clearance and component alignment after repair
• Safe, general-purpose replacement for common appliance fastening needs

• Turn off power and disconnect the appliance before accessing internal components
• Use the correct screwdriver or bit; avoid overtightening to prevent thread or part damage
• Keep hardware and small parts away from children and pets

A factory-matched Almond crème touch-up paint bottle to restore small chips, scratches, and worn spots on Almond-finish appliances. Helps blend blemishes into surrounding finish for a cleaner, more consistent look. What it does:

• Provides color-matched coverage for small surface chips and scratches on Almond-finish appliances
• Restores appearance without replacing large panels or trim
• Helps hide everyday wear and minor cosmetic damage
• Dries to a durable finish that blends with factory color

• One (1) bottle of Almond crème touch-up paint

• Shake well before use and test on an inconspicuous area first
• Clean and dry the surface thoroughly; remove loose paint and grease
• Apply sparingly in thin coats, allowing recommended drying time between coats
• Use in a well-ventilated area and follow all safety label instructions; wear gloves and eye protection

This Almond Creme color finish panel restores the original look of your appliance where the finish is worn, scratched, or mismatched. It provides a factory-style color match to keep the exterior appearance consistent. What it does:

• Replaces damaged or discolored finish panels to restore appliance appearance
• Covers scratches, chips, and worn paint on the affected area
• Matches the Almond Creme factory color to maintain a cohesive look
• Helps maintain resale value and overall visual condition

• Disconnect power to the appliance before beginning any work
• Handle panel carefully to avoid scratching the finish during installation
• Align tabs and mounting points, then secure with existing fasteners as required

This replacement Screw-Stat secures the appliance thermostat or temperature sensor so it stays in the correct position for reliable temperature sensing and consistent control performance. Simple, direct replacement for a lost or damaged mounting screw. What it does:

• Secures the thermostat/temperature sensor to the cabinet or mounting bracket.
• Keeps the sensor in firm contact for accurate temperature readings and stable cycling.
• Replaces stripped, missing, or damaged screws that can cause a loose sensor, intermittent temperature control, or rattling.
• Small hardware piece that supports proper operation of the temperature control system.

• Disconnect power to the appliance before accessing internal components.
• Use the proper screwdriver to avoid stripping the screw head; replace with like hardware.
• Do not overtighten—tighten just enough to secure the thermostat without distorting it.