K45sswh Parts

This factory fastener secures appliance components and panels in their intended positions. Replacing a missing, stripped, or corroded screw restores a tight fit, helping maintain alignment and reduce looseness and vibration-related noise.

• Fastens brackets, covers, and internal parts to the cabinet or frame
• Replace if the head is rounded, threads are worn, corroded, or the screw is missing
• Helps address rattling, buzzing, or wobbling caused by loose hardware
• Supports proper alignment of panels and assemblies

• Disconnect power and, if applicable, shut off water before servicing
• Use the correct driver size/type to prevent stripping the head
• Start threads by hand to avoid cross-threading; do not overtighten (especially into plastic)
• Replace one-for-one in the original location and orientation

This is a small spring lock washer used as a fastener in various appliances. It sits under a bolt or screw head to prevent loosening caused by vibration during operation. Replace this washer if it is flattened, cracked, or missing, which can cause components to become loose over time.

Secures housing panels and internal brackets on your stand mixer. Replace if screw is missing, stripped, or damaged to restore tight assembly.

Size: 6-32 x 9/32 inch.

This trim band replaces damaged or missing outer oven door trim to restore a clean, finished appearance. It's a cosmetic, direct-replacement piece that covers the door edge and conceals the mounting gap. What it does:

• Restores the oven's exterior finish by replacing scratched, dented, or bent trim.
• Covers exposed edges and mounting seams for a seamless look.
• Helps prevent buildup of grime where trim is missing or separated.
• Stops minor rattling or movement caused by loose or damaged trim.

• Disconnect power to the appliance before starting any repair.
• Handle edges and nearby glass with care; wear cut-resistant gloves.
• Installation may require removing the oven door or control panel to access mounting clips—verify fit and alignment before final fastening.

This is a small cylindrical sleeve that fits over a rotating shaft inside the dishwasher, typically serving as a bushing or bearing surface for the spray arm or wash motor assembly. It helps reduce friction and keeps components properly aligned during operation. Replace it if you notice the spray arm wobbling, water leaking around the shaft, or unusual grinding noises during the wash cycle.

This flat washer provides a durable spacer and load-distribution surface for fasteners in laundry appliances, helping secure components and reduce wear. It's a simple replacement that restores proper fastening and alignment where a worn washer is causing issues. This is for 1 washer, the photo is an example of the washer.  

What it does:

• Distributes nut/bolt pressure to protect mounting surfaces and prevent loosening
• Maintains correct spacing and alignment of panels, brackets, or moving parts
• Helps reduce vibration-related noise and abrasion at fastener points
• Common symptom: loose or rattling panels or hardware where a washer has deteriorated

What's included:

• One flat washer

Install notes:

• Turn off power and unplug the appliance before accessing panels or hardware
• Remove the fastener, replace the old washer with the new one, and re-torque to the OEM-recommended specification
• Inspect surrounding hardware and replace any damaged screws or nuts for a secure repair

Seals the planetary gear case to prevent grease leaks. Replace if oil appears around the outer case or after opening the mixer for repairs. Confirm fit.

This motor brush maintains electrical contact between stationary and rotating parts in appliance motors. It transfers electrical current to the motor's rotor while allowing smooth rotation during operation. Replace when the motor sparks, runs intermittently, or stops working to restore proper motor function.

This replacement screw is a direct-fit fastener used to secure appliance panels and components, restoring proper fit and reducing movement. Ideal when original screws are stripped, missing, or damaged. What it does:

• Secures panels, trim, brackets, and other serviceable components to prevent rattling or misalignment
• Matches original fastener form for correct fit and reliable function
• Helps restore proper clearance and component alignment after repair
• Safe, general-purpose replacement for common appliance fastening needs

• Turn off power and disconnect the appliance before accessing internal components
• Use the correct screwdriver or bit; avoid overtightening to prevent thread or part damage
• Keep hardware and small parts away from children and pets

This is a cover designed for the coin box assembly on a commercial-style dishwasher or laundry appliance. It protects the coin mechanism from tampering and debris. Replace this cover if it is cracked, broken, or missing, which can leave the coin mechanism exposed and vulnerable to damage.

This is the gearcase (gearbox) housing for a stand mixer, which contains and supports the internal gears that transfer motor power to the mixing attachments. It serves as the structural enclosure for the gear train assembly. Replace this part if the gearcase is cracked, leaking lubricant, or if the gears are no longer properly supported, causing unusual noises or wobbling during operation.

This replacement Screw-Stat secures the appliance thermostat or temperature sensor so it stays in the correct position for reliable temperature sensing and consistent control performance. Simple, direct replacement for a lost or damaged mounting screw. What it does:

• Secures the thermostat/temperature sensor to the cabinet or mounting bracket.
• Keeps the sensor in firm contact for accurate temperature readings and stable cycling.
• Replaces stripped, missing, or damaged screws that can cause a loose sensor, intermittent temperature control, or rattling.
• Small hardware piece that supports proper operation of the temperature control system.

• Disconnect power to the appliance before accessing internal components.
• Use the proper screwdriver to avoid stripping the screw head; replace with like hardware.
• Do not overtighten—tighten just enough to secure the thermostat without distorting it.

If your mixer won't spin or makes grinding noises, the planetary gear assembly may be worn. This part transfers motor power to attachments. Moderate DIY.