K45sswh-0Ss Parts

Called and gave the model number. You had it in stock. Work perfectly. Talked to two different women on two days. No pressure, so very nice and pleasant. I am keeping your name and number. Thank you for a very pleasant experience. John Thomas Read more

After ordering the speed lever, I watched one of the videos about disassembling the mixer. I followed the instructions pretty much to the letter except I found I spent more time cleaning and air dusting around the motor to get the accumulated flour dust out. The insides of the mixer haven't been touched in 30 years. About the most difficult part of disassembly was the 4 screws holding the mixer head to the stationary base. these screws have beveled cuts designed to lock the screws in place, I... Read more

After ordering the speed lever, I watched one of the videos about disassembling the mixer. I followed the instructions pretty much to the letter except I found I spent more time cleaning and air dusting around the motor to get the accumulated flour dust out. The insides of the mixer haven't been touched in 30 years. About the most difficult part of disassembly was the 4 screws holding the mixer head to the stationary base. these screws have beveled cuts designed to lock the screws in place, I... Read more

Found the broken parts upon disassembly. Ordered new parts. Parts were shipped very quickly. Read more

Found the part on your website, switched out the plates, and now it works beautifully. Thank you! Read more

Watched videos available on APP's website, then ordered all necessary parts. Once parts arrived, just followed the videos again, step-by-step, to repair the mixer. I am NOT a "handyman", but with APP as my resource, I did it. Mixer running great now. Read more

• Touchpad does not respond

Checked out You tube video. Easy tune up. One gasket was damaged and I did not notice that the brush holders has no brushes. I believe a quick call to Appliance parts pros will fix this, besides I need a few more parts. I expect to get another 20+ years from this KitchenAide mixer, once repairs are competed. Watch out for the single lock washer located on the rear upper housing screw, you don't want to lose this! Read more

My brother purchased an older model KitchenAid mixer. It works great. I ordered the Dough hook and the flat beater on Ebay. They did not fit. They were too long. After investigating the model number, my model is about 30 years old, I called Appliance Pros and they were very helpful in finding the correct parts for me. I ordered, and they work great. Thanks for your help. Read more

Replaced the armature bearing at the front of the mixer next to the gear case and replaced the gasket on the gear case. Read more

Found the broken parts upon disassembly. Ordered new parts. Parts were shipped very quickly. Read more

I WENT ONLINE AND ORDERED THE PART ON A TUESDAY. IT WAS DELIVERED BY FED EX ON WEDNESDAY. GREAT SERVICE. Read more

Watched some Youtube videos to learn how to disassemble the appliance which made the job very easy. As a retired engineer and electrician it wasn't too difficult to repair the unit. Everything is now working and as good as new. Read more

I followed the online tutorials, there are many....replaced the PLASTIC part that had worn out Part #: AP4325266 (241764), and also the roll pin, Part #: AP3038054 (9703442) that held it in place with the handle. THIS IS THE HARDEST part of the entire repair, pounding out the roll pin and pounding it back in. A special tool should probably be used for this. I had a small specialized driver bit that "fit" for the job, so I abused it. Probably didn't need to BUY a NEW roll pin, ( it HAS be... Read more

Replaced gear Read more

For most 20-year-old KitchenAid Blenders the grease packed inside begins to break down into UCK and oil which will drip through the old gaskets. After breaking down the case and removing all of the old grease and oil I cleaned all the gearing and shafts. I replaced the case gasket, the 2 shaft gaskets that the lower orbital gear slides up, and then the o-ring on the main shaft after everything was installed. I did a break-in run on med speed for one hour and then tapped the chrome ring off... Read more

Well after spending more then 30 minutes, and with the assistance of a great Consumer Support Tech, Mr. Curtis(first name), we finally figured out how to ajust a "simple" adjustment bolt in my Kitchen Aid miser. I would like to give Mr. Curtis my thanks for assisting and been so patience with this "Mr Know" everything Puertorrican. Read more