Kawe577bwhi Parts

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed

This replacement sleeve fits over a rotating shaft to reduce friction and protect the mating surface, helping restore smooth operation and reduce noise. Use when a worn sleeve causes rubbing or uneven movement. What it does:

• Acts as a bushing to prevent metal-to-metal contact on a rotating shaft
• Reduces friction and wear on the shaft and surrounding components
• Helps stop rubbing, scraping, or squeaking noises caused by a worn sleeve
• Restores proper alignment for smoother, quieter operation

• Disconnect power (and gas, if applicable) before starting any repair
• Use basic hand tools; no special training required for most installations
• Inspect the shaft and mating surfaces; replace if excessively scored or damaged
• If press-fit, install carefully to avoid damaging the new sleeve; do not use solvents as a substitute for proper fit

This E ring is a small metal retaining clip that secures shafts, pulleys, and other rotating parts to prevent axial movement. It restores correct part positioning so assemblies run smoothly and stay aligned. What it does:

• Acts as a snap/retaining ring to hold components on a shaft or in a groove
• Prevents pulleys, bearings, or spacers from sliding out of place
• Common symptom: loose or shifting pulley, increased wobble, noise, or component disengagement
• Small, inexpensive part whose failure can allow adjacent parts to migrate and cause additional damage

• Disconnect power to the appliance before beginning any repair
• Use snap-ring pliers or needle-nose pliers and wear eye protection when installing or removing
• Ensure clip seats fully in the shaft groove and that mating surfaces are clean and undamaged
• Replace any damaged mating hardware rather than reusing a deformed clip

For end of drain hose.

Part# is one rivet.

Spring-style hose clamp that secures flexible appliance hoses to fittings, helping keep connections tight to reduce leaks and maintain proper water flow. Use it to replace a worn or damaged clamp and restore a reliable hose seal. What it does:

• Compresses around a flexible hose to lock it onto barbs or fittings
• Helps prevent drips, leaks, and water pooling at hose connections
• Keeps hoses from slipping off during appliance operation
• Useful when a clamp is corroded, stretched, or no longer holds tension

• Disconnect power and shut off water to the appliance before starting any repairs
• Use pliers to compress the clamp for removal and installation; keep hands and face clear when releasing tension
• Inspect the hose and fitting for damage; replace the hose if cracked or excessively worn

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

Bottle with brush. Color: Harvest Gold. It's 0.6 fluid ounces.

This agitate gear washer is a small flat washer used with the washer's agitate gear to ensure proper spacing and smooth engagement. It helps maintain correct gear alignment so the agitator can move laundry effectively. What it does:

• Provides a stable spacer between the agitate gear and mating components to prevent excess play
• Helps maintain correct gear alignment for consistent agitator movement
• Reduces metal-on-metal contact that can cause noise or premature wear
• Commonly replaced when the agitator feels loose, makes grinding noise, or causes uneven agitation

• High-level replacement: remove agitator/gear per service manual to access washer; reinstall in original orientation
• Use manufacturer torque/settings for reassembly; do not overtighten
• Inspect adjacent gear and splines for wear; replace any damaged components
• Disconnect power and follow safety procedures before servicing the washer

Color: White

Includes gasket sealer.

A cam sleeve that supports and guides the cam on its shaft to keep the cam-driven mechanism moving smoothly. Replacing a worn sleeve helps restore correct alignment and reduces binding or intermittent movement. What it does

• Centers and stabilizes the cam on its shaft for reliable engagement.
• Prevents metal-on-metal wear between the cam and shaft.
• Helps eliminate binding, wobble, or uneven operation caused by a worn sleeve.
• Common symptom of failure: noise, sticking, or irregular movement from the cam-driven mechanism.

• Disconnect power to the appliance before beginning any repair.
• Access typically requires removing the appropriate service panel; follow the model service manual.
• Inspect mating cam and shaft for wear; replace any damaged components.
• Reassemble panels and verify proper operation before returning the appliance to service.

A replacement thrust bearing that supports the washer transmission shaft to reduce axial wear and help the gearbox rotate more smoothly. Use this bearing to address noisy transmission operation and reduce metal-on-metal wear when the original is worn. What it does:

• Supports axial load on the transmission/gearcase shaft to reduce friction and wear
• Helps prevent grinding, scraping, or other metal-on-metal noises from the gearbox
• Can reduce rough or noisy spin and improve agitation when a worn bearing is the cause
• Helps maintain proper alignment of transmission components for smoother operation

• Disconnect power and water supply and drain the washer before beginning any work.
• Replacement requires accessing the agitator/gearcase per the OEM service manual and may involve transmission/gearcase disassembly.
• Inspect nearby seals, fasteners and other bearings while servicing; replace damaged parts to avoid premature failure.