Kdpr234gbs0 Parts

This inline fuse is a replaceable safety device that protects your appliance's wiring and components from overcurrent. It restores circuit protection so the appliance can operate safely after a blown fuse is replaced. What it does:

• Protects the wiring harness and electrical components by interrupting power if a short or overload occurs
• Commonly used where a single-point fuse is needed inline with a circuit
• Resolves symptoms like a non-starting unit, intermittent power loss, or a tripped circuit when caused by a blown fuse
• Works as part of the appliance's electrical protection system when installed in the proper harness location

• Disconnect power to the appliance before inspecting or replacing the fuse
• Visually check the blown fuse or use a multimeter before replacing
• Install only in the correct harness location and ensure secure wire connections
• If the replacement fuse blows immediately, stop and diagnose the underlying short or fault

This factory fastener is a #10-16 screw used to secure appliance panels and components. Replacing worn or missing hardware restores a tight fit, helps prevent rattles, and keeps parts properly aligned for dependable operation.

• Secures brackets, panels, and covers to the cabinet or frame
• Replaces missing, stripped, or corroded mounting hardware
• Helps reduce vibration and rattling from loose mounts
• Correct 10-16 thread to match designated OEM mounting points

• Disconnect power and shut off water or gas supply before servicing
• Match the screw to the original location using your model's diagram
• Start threads by hand to avoid cross-threading; tighten snugly—do not overtighten
• If replacing multiple screws, swap one at a time to maintain alignment

Cover-Box protects the appliance's control box and internal wiring by enclosing electronic components to keep out dust and accidental contact, helping maintain reliable operation and reduce the chance of component damage. What it does:

• Encloses and protects the control box and wiring from dirt, debris and incidental contact.
• Helps prevent exposed wires and component damage that can lead to intermittent operation or electrical faults.
• Restores structural protection when the original cover is cracked, warped, or missing.
• Matches OEM fit and mounting points to secure the control assembly in place.

• Disconnect power to the appliance before beginning any service.
• Remove screws or fasteners securing the old cover; keep hardware for reuse unless damaged.
• Ensure wiring and connectors are routed correctly and fully seated before reinstalling the cover.

This diverter directs dishwasher wash water to the upper spray arm, restoring proper water distribution for the top rack. Replacing a worn or broken diverter helps recover consistent spray coverage and cleaning performance. What it does:

• Redirects wash water flow to the upper spray arm so the top rack receives proper spray.
• Ensures even water distribution for improved cleaning of items on the upper rack.
• Helps correct symptoms such as poor cleaning on the top rack or reduced spray to the upper spray arm.
• Works with the dishwasher's spray system—operates with water pressure from the pump to route flow.

• Disconnect power and shut off the water supply to the appliance before servicing.
• Use basic hand tools and follow the appliance's service diagram; avoid forcing tabs or fittings.
• Inspect nearby seals, gaskets and mounting tabs during replacement and replace if damaged.
• After installation, run a short cycle to check that the upper spray arm receives water and check for leaks.

This cup shelf assembly replaces a damaged or missing refrigerator door shelf to restore secure storage for cups, bottles and small items. It snaps into the door for everyday organization and keeps items from shifting during use. What it does:

• Provides a stable shelf on the refrigerator door to hold cups, bottles and jars
• Replaces cracked, broken or missing door shelf that lets items fall or shift
• Restores original door storage layout and helps prevent spills
• Fits the door's existing mounting points for a secure hold

• One cup shelf assembly (11")

• Remove contents from the door area before installing
• Often snaps into place; may require basic hand tools to remove the old shelf
• Do not force parts; align mounting tabs and press evenly until seated

The Silverware Basket is an OEM component specifically designed for Whirlpool built-in dishwasher models. Located in the lower rack, the silverware basket neatly organizes and separates cutlery during the wash cycle.

Causes of a bad silverware basket include material degradation from prolonged chemical and heat exposure and loosening its construction. Warping from years of rack movement is also possible. 

Symptoms of a bad silverware basket include:

• Ungrouped or tangled silverware after cleaning  
• Broken or missing tines from the collecting rack
• Leaks around seals from structural defects

Replace with this authentic OEM Whirlpool basket to maintain organized cutlery separation and wash effectiveness. Rely on its construction to protect edgeware while delivering maximum sanitization performance. Compatible with additional brands including KitchenAid and some stainless Kenmore models.

The Leveling Leg is an OEM part for Whirlpool dishwashers. It is an adjustable leg that is used to level the dishwasher and stabilize it when installed under the kitchen counter or inside cabinetry.  

Causes of a bad leveling leg often relate to normal wear and tear over time, repeated adjustments, or potential overtightening that leads to thread damage.

Symptoms of a bad leveling leg include:

• The dishwasher is not sitting level and appears unstable  
• Leaks occurring around the dishwasher perimeter or door seal
• Drainage or pooling of water inside the dishwasher
• Cabinetry or countertops showing scratches or wear

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

The Terminal Block is an OEM part for Whirlpool dishwashers.The terminal block facilitates the flow of electricity throughout the appliance, enabling functions like water heating, pump operation, and cycle control.

Causes can be normal wear over time, or damage from moisture exposure. If you notice any of the above symptoms, replace the terminal block with this genuine OEM part to restore reliable electrical connections and proper operation.

Symptoms of a bad terminal block include:

• The dishwasher not starting or unexpected beeping/error codes
• Sudden lack of hot water or drying issues
• Electrical shock hazard from exposed terminals

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Clip is an OEM part for Whirlpool dishwashers. It securely attaches the drain hose in place, directing wastewater out of the dishwasher during drain cycles.

Causes of a bad clip can be cracks, breaks, or deformations causing weakened grip. Normal wear and repeated drain cycles can also damage the clip over time.

Symptoms of a bad drain hose clip include:

• Water or leaks around the base of the dishwasher
• Puddles forming due to the hose slipping out of place
• Improper drainage if the hose is not positioned correctly

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Dishwasher Track/Support is an OEM component specifically designed for Whirlpool dishwashers. It anchors underneath the dish rack and slides upon which it rolls. 

Causes of a faulty track/support can include cracks, deformities or other damage accumulating from years of bearing weight.

Symptoms of a bad track/support include: 

• Dishes failing to properly secure inside wash rack
• Rack sliding out of position unintentionally  
• Noisy vibrations or shaking heard from below

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwasher models.

This push retainer is a small press-on fastener that secures components to shafts or studs inside your appliance. It restores a tight, reliable hold so knobs, trim, or linkages don't loosen or fall off during use. What it does:

• Presses onto a shaft or stud to secure knobs, trim, or linkages—no threads required
• Maintains spring tension to resist vibration during normal operation
• Replaces a missing, bent, or weakened retainer
• Common symptoms: loose or wobbly knobs/trim, parts slipping off, or a retainer that won't stay on

• 1 push retainer

• Disconnect power; for gas appliances, also shut off the gas supply
• Access the shaft/stud and carefully remove the old retainer with pliers; avoid damaging adjacent plastic parts
• Press the new retainer on squarely using a deep socket or nut driver; do not hammer directly
• If the mating shaft or component is damaged or deformed, address that before installing the new retainer

A pronged cup washer that secures and cushions mating parts on appliances, restoring proper fit and reducing wobble. Replaces worn or damaged cup-style washers to help maintain stable component alignment and reliable operation. What it does:

• Fits into a cup or socket to hold shafts, knobs, or trim pieces in place
• Pronged design grips the mounting surface to prevent rotation and slippage
• Helps reduce vibration and noise caused by loose or worn washers
• Commonly used when a knob, shaft, or trim feels loose or wobbly

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove the related knob or trim carefully to access the washer; note orientation for correct reassembly
• Press the washer fully into the cup or socket so the prongs engage the mounting surface
• Inspect the surrounding components for wear and replace any damaged parts

This 10-24 threaded screw secures appliance components that use a #10 machine screw. It provides reliable fastening for panels, brackets, and assemblies so parts stay aligned and stable during normal use and service. What it does:

• Fastens panels, brackets, or assemblies that accept a 10-24 machine screw
• Maintains alignment and structural connection under normal operating loads
• Replaces worn, stripped, or missing screws to restore secure mounting
• Works with sheet-metal and component mating nuts or threaded inserts commonly used in appliances

• One 10-24 threaded screw

• Power tools can be used; avoid overtightening to prevent stripped threads or damaged components
• Disconnect power and follow all safety steps for your appliance before servicing
• Ensure proper engagement and torque to avoid damage

Number-8, 18-thread screw used to secure panels, brackets and small assemblies in Whirlpool appliances. Replacing a missing or damaged screw restores secure mounting and helps stop rattling or loose parts. What it does:

• Fastens trim, panels, brackets or small appliance components that use a #8-18 threaded fastener
• Restores secure mounting when a screw is lost, stripped or damaged
• Helps eliminate vibration-related noise from loose parts
• Simple replacement part for basic fastening needs

• Disconnect power to the appliance before servicing and work on a cool, stable surface
• Use the correct screwdriver or driver bit to avoid cam-out or stripped heads
• Thread in straight and tighten until snug; do not over-torque to avoid stripping threads or damaging components
• Replace with the identical screw type and size for proper fit and function

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Size: 8-32 x 1/2 inch.