Kdpr234gbs0 Parts

The Harness-Wire Assembly is an OEM component specifically designed for Whirlpool dishwashers. This assembly consists of wiring harnesses that connect and transmit power to various electronic control boards and components inside the dishwasher.

Symptoms of a bad harness-wire assembly can include intermittent or complete failure of functions like dispensing, heating, draining, or the wash motor running due to open or damaged connections within the wiring. 

Causes may involve normal wear and strain on wires from repeated use over time, moisture damage to insulation coatings on wires, or damage to connectors from improper installation or handling. 

Causes of a bad harness-wire assembly include:

• Portions of the cycle like heating not activating
• Wash motor failing to run or running intermittently
• No dispensing from the detergent dispenser
• Drain pump failing to engage 

This OEM part is also compatible with some KitchenAid, Jenn-Air, Amana, and Kenmore models that utilize similar components.

This air inlet damper controls cold-air flow from the freezer into the refrigerator compartment to help maintain proper fresh-food temperatures. Replacing a faulty damper restores balanced airflow and more consistent cooling. What it does:

• Regulates the amount of cold air entering the fresh-food section from the freezer.
• Opens and closes as the fridge cycles to maintain set temperatures.
• Commonly replaces stuck, broken, or noisy dampers that cause uneven cooling.
• Often used when the refrigerator is warm while the freezer remains cold or when temperatures fluctuate.

• Disconnect power to the appliance before starting any repair.
• Remove interior panels or grille per your model's service instructions to access the damper; keep screws and clips organized.
• Handle plastic fins and actuator gently to avoid damage; do not force the damper into position.
• Reconnect power and verify damper operation and temperature regulation after installation.

This replacement brace is a structural support bracket that helps stabilize and secure appliance components for reliable operation. Installing the correct brace restores alignment and reduces movement that can cause noise or wear. What it does

• Provides structural support to internal or external assemblies to keep parts properly aligned
• Helps reduce vibration and rattling caused by loose or damaged supports
• Prevents excess movement that can lead to premature wear of adjacent components
• Commonly replaced when the original bracket is bent, cracked, or missing

• One replacement brace/support bracket

• Use appropriate tools and fasteners for your model; retain any original screws if reusable
• Disconnect power (and water if applicable) before beginning any repair for safety
• Inspect surrounding components and mounting points; replace damaged hardware as needed

This replacement support is a mounting bracket that secures and stabilizes internal components, restoring proper alignment and reducing movement or vibration. It's a direct-fit service part when the original support is cracked, bent, or missing. What it does:

• Provides a stable mounting point for internal assemblies to prevent shifting during operation
• Restores proper alignment to reduce rattling, vibration, or intermittent contact issues
• Helps maintain correct spacing for connected components and wiring
• Prevents further wear or damage caused by loose parts

• One support

• Disconnect power before starting any repair to avoid shock or injury
• Handle small fasteners carefully; keep track of any clips or screws removed
• Reuse original hardware only if undamaged;

This wire harness assembly replaces a damaged or worn wiring group that connects appliance components so electrical signals and power reach the controls and motors reliably. Restores proper circuit routing and connector fit where the original harness is broken or burned. What it does:

• Routes and connects power and control signals between major components (control, motor, sensors).
• Replaces frayed, melted, or damaged wiring that can cause intermittent operation or component failure.
• Helps stop issues like no-start, certain controls not responding, or components losing power.
• Provides factory-style connector ends for a direct-fit electrical connection.

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury.
• Support and secure the harness away from sharp edges, moving parts and heat sources; use existing clips or ties.
• If any connectors or insulation show heat damage or corrosion, inspect related components and replace as needed.

This control trim panel replaces the external trim that surrounds the appliance's user controls, restoring a clean appearance and protecting buttons and the display. It helps make the control area look new and prevents dirt from collecting around controls. What it does:

• Covers and protects the control area and display from spills, grease, and everyday wear
• Provides a finished surface for buttons, knobs, or touch controls to operate smoothly
• Restores the appliance's factory appearance when the original panel is cracked, warped, or faded
• Helps keep contaminants out of the control cavity that can lead to button sticking or display issues

• One control trim panel

• Power off and unplug the appliance (or switch off circuit breaker) before beginning any work
• Remove any retaining screws, bezels, or fasteners to lift off the old panel; retain mounting hardware unless replacing
• Handle carefully to avoid scratching the finish or damaging clips during installation

This hose clamp secures flexible hoses to fittings to prevent leaks and keep connections tight on dishwashers and similar appliances. It's a simple replacement that restores a secure hose seal and prevents water from escaping. What it does

• Holds a drain or water hose firmly to a barb or fitting to stop leaks
• Restores a tight connection when original clamp is corroded, cracked, or loose
• Helps prevent water pooling beneath the appliance and related drip issues
• Typical use: clamp for dishwasher drain/water hose connections

• One hose clamp as pictured

• Disconnect power and shut off water supply before servicing the appliance
• Slide clamp over hose, seat hose fully on the fitting, then tighten clamp evenly until snug
• Replace any corroded or damaged clamps; do not overtighten

This 3-channel feedtube routes water to the appliance's dispenser/ice system to ensure proper delivery where needed. Replaces a damaged or cracked feedtube to help restore correct water flow and reduce leaks. What it does:

• Directs water through three separate channels to the ice maker/dispenser plumbing
• Prevents cross-flow between channels for reliable filling and dispensing
• A damaged tube can cause leaks, weak dispensing, or the ice maker not filling
• Fits the OEM routing to maintain correct water pressure to downstream components

• One 3-channel feedtube

• Disconnect power and shut off the water supply before servicing
• Handle carefully to avoid kinking; inspect and replace any worn seals or grommets
• Tighten connections evenly to prevent leaks; check for leaks after restoring power/water
• Use manufacturer diagrams to confirm routing and orientation during installation

This spacer positions and supports the appliance tank/tub assembly to maintain proper alignment and spacing for reliable operation. Replaces a worn or damaged spacer to restore correct fit and reduce movement. What it does:

• Keeps the tank/tub assembly correctly spaced and aligned with the cabinet and mounting points
• Helps prevent rubbing, binding, and excess vibration caused by a missing or damaged spacer
• Restores proper clearance to support seals and hoses that rely on correct tank positioning
• Useful when reassembling the appliance after service or repair

• One spacer

• Disconnect power and water supply before starting any repair
• Access may require removal of outer panels, console, or access covers depending on model
• Handle parts carefully to avoid damaging surrounding seals and wiring; reuse fasteners unless replacement is specified

The Drain Hose is an OEM part for Whirlpool built-in dishwashers. As the tube removes wastewater after each cycle, it plays a key part in sanitizing dishes. 

Causes of a bad Drain Hose can include mineral deposits inside over many years reducing flow. Cracks may also form from constant flexing as it transport water to the garbage disposer or sink drain.

Symptoms of a bad drain hose include:

• Puddles or pooling inside the dishwasher 
• Incomplete drainage leaving residue on dishes
• Leaks around hose connections

This genuine Whirlpool replacement is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore too. 

This inner door jumper is a short wiring harness that restores electrical connections inside the appliance door for functions such as the fan, vent, dispenser and door switch. It helps re-establish reliable power and signal routing at the door assembly. What it does:

• Routes power and control signals between the cabinet and inner door components (fan, vent, dispenser, door switch)
• Replaces damaged or frayed jumper wiring that can cause intermittent or no operation of door-mounted features
• Helps stop issues like non-responsive dispenser, fan or vent functions when caused by a broken door connection
• Matches OEM routing and connectors for a direct electrical replacement

• Recommended for technicians or experienced DIYers; disconnect power before starting
• Inspect connector ends and harness routing; avoid pinching or sharp bends during reassembly
• Verify correct connector orientation and secure any retained clips to prevent chafing

This replacement support is a molded mounting bracket that secures internal components and helps keep assemblies aligned for reliable operation. It restores proper positioning and reduces movement or vibration that can cause noise or wear. What it does:

• Secures and supports an appliance internal assembly to maintain correct alignment
• Reduces vibration and rattling from loose or worn mounting points
• Helps prevent premature wear by keeping parts properly seated
• Restores fit where a broken, cracked, or missing support causes instability

• One support mounting bracket

• Disconnect power (and water, if applicable) before beginning any repair
• Access and removal may require removing panels or trim; keep fasteners organized
• Inspect adjoining components and fasteners; replace any damaged hardware

The Lower Door Seal Assembly is an OEM part for Whirlpool dishwashers. As a key component, this seal is designed to create a tight barrier between the door interior and tub during wash cycles. The pliable rubber seal provides a sturdy gasket to block water, detergent, and sound.

Causes of failure involve mineral buildup, cracks from repeated use, or degradation of adhesive over time compromising the seal. 

Symptoms of a faulty seal assembly include: 

• Puddles or leaks from beneath the door frame
• Higher water consumption or longer cycles   
• Increased noise levels during operation

This OEM Whirlpool replacement is also compatible with select KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and other brands.

The Pump Filter is an OEM part for Whirlpool dishwashers. It is a filter that screens debris from entering the pump and wash arms during the dishwashing cycle.

The pump filter is responsible for catching food particles and other residue, preventing clogs and maintaining optimal water flow throughout the dishwasher. It ensures the pump and other internal components are kept clean.

Symptoms of a clogged or damaged pump filter include:

• Excessive noise or vibrations coming from the pump area
• Slow or reduced water drainage
• Built up residue in the filter housing or sump area
• Incomplete cleaning or drying results

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.