Kdtm704kps Parts

This wire harness assembly replaces a damaged or worn wiring group that connects appliance components so electrical signals and power reach the controls and motors reliably. Restores proper circuit routing and connector fit where the original harness is broken or burned. What it does:

• Routes and connects power and control signals between major components (control, motor, sensors).
• Replaces frayed, melted, or damaged wiring that can cause intermittent operation or component failure.
• Helps stop issues like no-start, certain controls not responding, or components losing power.
• Provides factory-style connector ends for a direct-fit electrical connection.

• Disconnect power (unplug or shut off breaker) before servicing to avoid shock or injury.
• Support and secure the harness away from sharp edges, moving parts and heat sources; use existing clips or ties.
• If any connectors or insulation show heat damage or corrosion, inspect related components and replace as needed.

This hose clamp secures flexible hoses to fittings to prevent leaks and keep connections tight on dishwashers and similar appliances. It's a simple replacement that restores a secure hose seal and prevents water from escaping. What it does

• Holds a drain or water hose firmly to a barb or fitting to stop leaks
• Restores a tight connection when original clamp is corroded, cracked, or loose
• Helps prevent water pooling beneath the appliance and related drip issues
• Typical use: clamp for dishwasher drain/water hose connections

• One hose clamp as pictured

• Disconnect power and shut off water supply before servicing the appliance
• Slide clamp over hose, seat hose fully on the fitting, then tighten clamp evenly until snug
• Replace any corroded or damaged clamps; do not overtighten

This 3-channel feedtube routes water to the appliance's dispenser/ice system to ensure proper delivery where needed. Replaces a damaged or cracked feedtube to help restore correct water flow and reduce leaks. What it does:

• Directs water through three separate channels to the ice maker/dispenser plumbing
• Prevents cross-flow between channels for reliable filling and dispensing
• A damaged tube can cause leaks, weak dispensing, or the ice maker not filling
• Fits the OEM routing to maintain correct water pressure to downstream components

• One 3-channel feedtube

• Disconnect power and shut off the water supply before servicing
• Handle carefully to avoid kinking; inspect and replace any worn seals or grommets
• Tighten connections evenly to prevent leaks; check for leaks after restoring power/water
• Use manufacturer diagrams to confirm routing and orientation during installation

This inner door jumper is a short wiring harness that restores electrical connections inside the appliance door for functions such as the fan, vent, dispenser and door switch. It helps re-establish reliable power and signal routing at the door assembly. What it does:

• Routes power and control signals between the cabinet and inner door components (fan, vent, dispenser, door switch)
• Replaces damaged or frayed jumper wiring that can cause intermittent or no operation of door-mounted features
• Helps stop issues like non-responsive dispenser, fan or vent functions when caused by a broken door connection
• Matches OEM routing and connectors for a direct electrical replacement

• Recommended for technicians or experienced DIYers; disconnect power before starting
• Inspect connector ends and harness routing; avoid pinching or sharp bends during reassembly
• Verify correct connector orientation and secure any retained clips to prevent chafing

This replacement support is a molded mounting bracket that secures internal components and helps keep assemblies aligned for reliable operation. It restores proper positioning and reduces movement or vibration that can cause noise or wear. What it does:

• Secures and supports an appliance internal assembly to maintain correct alignment
• Reduces vibration and rattling from loose or worn mounting points
• Helps prevent premature wear by keeping parts properly seated
• Restores fit where a broken, cracked, or missing support causes instability

• One support mounting bracket

• Disconnect power (and water, if applicable) before beginning any repair
• Access and removal may require removing panels or trim; keep fasteners organized
• Inspect adjoining components and fasteners; replace any damaged hardware

This Pad-ins is a factory-style insulation pad that helps reduce heat transfer and dampen vibration inside the appliance. It restores original fit and helps protect nearby components from heat and abrasion. What it does:

• Provides thermal insulation to limit heat transfer to adjacent parts
• Cushions and dampens vibration and noise from moving components
• Helps prevent chafing or wear where panels or parts contact each other
• Can reduce symptoms such as hot spots, rattling, or scuffing near the pad location

• Disconnect power (and gas, if applicable) before starting any repair
• Remove panels as needed to access the pad; take photos for reassembly
• Peel-and-stick or adhesive-backed pads should be positioned carefully; press firmly to ensure adhesion
• If replacing adhesive-backed pads, remove old adhesive residue and follow OEM placement for best fit

The Lower Door Seal Assembly is an OEM part for Whirlpool dishwashers. As a key component, this seal is designed to create a tight barrier between the door interior and tub during wash cycles. The pliable rubber seal provides a sturdy gasket to block water, detergent, and sound.

Causes of failure involve mineral buildup, cracks from repeated use, or degradation of adhesive over time compromising the seal. 

Symptoms of a faulty seal assembly include: 

• Puddles or leaks from beneath the door frame
• Higher water consumption or longer cycles   
• Increased noise levels during operation

This OEM Whirlpool replacement is also compatible with select KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and other brands.

The Pump Filter is an OEM part for Whirlpool dishwashers. It is a filter that screens debris from entering the pump and wash arms during the dishwashing cycle.

The pump filter is responsible for catching food particles and other residue, preventing clogs and maintaining optimal water flow throughout the dishwasher. It ensures the pump and other internal components are kept clean.

Symptoms of a clogged or damaged pump filter include:

• Excessive noise or vibrations coming from the pump area
• Slow or reduced water drainage
• Built up residue in the filter housing or sump area
• Incomplete cleaning or drying results

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Replacement door hinge designed to restore proper alignment and smooth opening for compatible refrigerator doors. Replaces worn or damaged hinges to reduce sagging, rubbing, and uneven closing for better seal and operation. What it does:

• Supports and pivots the refrigerator door for smooth opening and closing.
• Restores correct door alignment to improve gasket contact and cold-air seal.
• Stops door sag, uneven gaps, or rubbing against the cabinet.
• Helps eliminate noisy or stiff door movement caused by a worn hinge.

• Disconnect power to the appliance and remove food from the door area before starting.
• Support the door securely while removing and installing the hinge to prevent dropping or damage.
• Reuse original fasteners only if undamaged; replace any stripped or corroded hardware.

The Float Switch is an OEM part for Whirlpool dishwashers. It is a safety component that detects water levels and monitors flood conditions. The float switch ensures the dishwasher only runs water when needed and shuts off water flow if it detects a potential leak or overflow situation. 

Symptoms of a bad float switch include: 

• The dishwasher fails to fill with water or stop the water when the cycle is complete
• Loud buzzing or humming noises coming from the float switch area  
• Water leaks inside or outside of the dishwasher due to overfilling
• Repeated error codes related to flooding or water level detection

Causes of a bad float switch could be wear and tear over time, defective wiring or electronic components inside the switch, or damage from moisture or leaks. 

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Dishwasher Plate-Latch Strike is an OEM part for Whirlpool dishwashers. It is a part that holds the dishwasher door shut during wash cycles. Precise alignment of the strike allows for tight sealing and proper engagement with the door latch.

Causes may arise from normal wear over lengthy use, deformations from repetitive door actions, or incidental damage.

Symptoms of a bad strike can include:

• Door that feels loose and doesn't fully latch closed
• Gaps seen around the door sealing surface
• Water leaks or insufficient drying performance
• Difficulty fully closing or reopening the door

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Center Wash Arm Assembly is an OEM part compatible with Whirlpool dishwashers. It is a multi-spraying component located in the center of the lower dish rack that helps deliver water for superior washing performance. The arm rotates during the cycle to wash all accessible surfaces of dishes.

Symptoms of a bad Center Wash Arm Assembly include:

• Incomplete or inadequate cleaning of dishes, especially those in the lower rack  
• Mineral or hard water deposits building up on dishes
• Reduced water pressure or spray pattern from the wash arm nozzle(s)

Causes of a bad center wash arm can be mineral deposits clogging the nozzle openings over time, or physical damage such as bending or breaking of the arm assembly or its mounting bracket.

This OEM replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore dishwashers.

The Lower Spray Arm is an OEM component specifically designed for Whirlpool brand dishwashers. This lower spray arm attaches to the bottom rack and rotates during the wash cycle to distribute water and cleaning chemicals across dishes. 

Causes of a bad lower spray arm can include mineral buildup inhibiting movement, cracks or breaks in the arm itself, or broken or missing spray nozzles. 

Symptoms of a bad lower spray arm include:

• Inadequate cleaning or rinsing of dishes on the bottom rack  
• Noticeable buildup or residue left on dishes after washing
• Noises, squeaks, or grinding sounds coming from the lower spray arm area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models. 

The Drain Hose is an OEM part for Whirlpool dishwashers. It channels water out of the dishwasher tub and into the garbage disposal or drain after each cycle. This drain hose is specifically designed to withstand frequent temperature fluctuations and mineral deposits without compromising its integrity over time.

Causes of a bad Drain Hose can include mineral buildup inside the hose restricting flow, cracks developing from repeated flexing during drain cycles, or cuts or abrasions from rough handling or sharp surfaces.

Symptoms of a bad Drain Hose include:

• Water not draining properly or draining slowly after cycles
• Puddles or leaks found near or under the dishwasher
• Musty smells from standing water inside or around the unit
• Possible flooded floors near the dishwasher area

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This heater terminal nut fastens the heating element stud on the outside of the tub, keeping the element seated and stable during wash and dry cycles. Replace if the original nut is missing, stripped, or corroded.

• Secures the heating element terminals to the tub exterior
• Maintains proper element position for consistent, reliable operation
• Direct replacement for a worn, missing, or rusted element terminal nut
• Common signs: loose heating element at the tub wall, rattling from the lower area, or visible damage/corrosion on the nut

• Safety first: Disconnect power at the breaker and allow the element to cool before servicing.
• Access the heater terminals from beneath the unit by removing the toe panel or carefully sliding the dishwasher out.
• Support the terminal stud and wiring while loosening/tightening to avoid twisting or stressing the element.
• Tighten snugly without overtightening; run a brief test cycle to confirm proper operation.