Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
If your range has a strong burning smell or won't power on, the terminal block may be heat-damaged. This insulated connector restores safe power flow.
Replaced it with the part I got from you. Read more
Replacement inner door glass panel for your oven door assembly. Installs behind the outer glass. Order if your inner glass is cracked, broken, or missing.
Ordered the replacement panel and disassembled the upper oven door, which was needed, as the inside glass areas needed some cleaning. Read more
If your oven door won't lock, stays locked after self-clean, or shows door lock errors, this door lock motor and switch assembly often solves the issue.
My appliance is a Whirlpool Accubake Wall Oven, single door. After using the tech sheet and measuring the ohms of the two micro switches that sends signals when the door is shut and locked, determined the lock was faulty. Pretty simple to change, the most difficult part was taking the digital face off of the oven without damaging the control board. TIP: take a picture of the latch switches to ensure you put the correct wires on the correct switch. Read more
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Replaced It With New One Read more
Fix a microwave that runs but won't heat food with this magnetron replacement. Moderately difficult repair requiring capacitor discharge safety steps.
I replaced the magnetron and diode. I don't know if the diode was bad, but since the majority of the work was taking the case apart, I figured it was easier to do it at the same time as the magnetron. The replacement magnetron I received was dented at the emitter end, but seems to work fine. It was a bit intimidating to work on a microwave with all the warning stickers on the cabinet, but the replacement went smoothly - the biggest difficulty was determining how to remove the panels of the... Read more
Oven not heating evenly or convection mode not working? This rear convection element restores even baking and roasting. 20-minute DIY repair.
Whirlpool convection oven. Access to convection element from inside. Three screws to remove plate covering fan blade. Then one screw to remove element bracket. I placed tape over the holes with the wires so they wouldn’t pull back into the panel. Remove old element at tabs and replace. Very easy fix. Removing door to oven made it easier to get to but not necessary. Read more
This ground screw secures the appliance's grounding wire or strap to the chassis or terminal area, creating a reliable bonding point. Replace a missing or damaged screw to restore a proper ground connection during installation or service.
I ordered the part; it came in 2 days! I watched the video. Repair went flawlessly! I will definitely order from you guys again! Great service and help with the install! Read more
Left side hinge receiver for door hinge. For right side hinge receiver use WP4455606.
I was able to order new hinge receiver brackets for the door. The repair was not that bad. I just had to take off the lower door, take the two trim pieces off the sides and unscrew the screws holding the oven into the face of the cabinet. Then slide it out about halfway and put a step stool under the front to keep it from tipping over. Then it was just a matter of taking off everything around the sides until I could take the brackets off, put the new brackets on, and put everything back... Read more
Door hinge receiver for wall ovens. Mounts inside the oven frame to hold the door hinge in place. Replace if cracked, deformed, or causing door alignment issues.
Replacement right-hand oven door hinge that provides the pivot point and spring tension for smooth opening and closing. Install when bent or worn.
The door hinge latches were bent, which made it difficult to remove the door and re-insert. The door hinge design was changed from a pin insert to a latch from the previous model. Unfortunately, the latch on the 24 inch oven is thin and easily bent, which is likely the source of the problem. I purchased spare door hinges to facilitate re-installing the oven door should I ever have problems with removing and inserting the door again. Read more
Replace your oven's left-hand door hinge to restore smooth opening and a proper seal. Fixes doors that won't close, sag, or have weak springs. Confirm fit.
Fix "meat probe shorted" or F3 E2 error codes with this oven temperature probe jack. Restores connection for probe-cook features in wall and range ovens.
Oven light won't turn on? This light transformer steps down voltage to power your oven cavity lights. Moderate DIY repair restores illumination.
Replaced the transformer and it was fixed. Not a difficult fix at all. Read more
This time-delay fuse protects the appliance's power circuit by opening when current exceeds a safe level while tolerating brief inrush current. Replacing a blown fuse can help restore power once the root cause is corrected. What it does:
I read up on others with this problem of microwave-wall oven combination Whirlpool Gold. We live in a very rural area and were not able to get ANYONE to service it - had 2 companies come out to inspect but they never returned. I have wonderful news! We replaced the fuse, bus fuse, and light bulb (quit working 2 years ago) and all is working. Thanks for the information and for the part diagram. Couldn't have done it without you. Read more
A factory screw with 8-32 machine threads used to secure brackets, panels, and internal components where specified. Restores a solid, factory fit when the original fastener is missing, stripped, or corroded. What it does:
Microwave not heating? This high voltage capacitor works with the magnetron and diode to generate heat. Moderate DIY repair with proper safety precautions.
Replaced the magnetron, capacitor and diode. Symptoms of failure were change in tone/noise put out by the microwave and no heat in the item being microwaved. Could have been a failure of either the diode, capacitor or the magnetron, but I believe it was the magnetron that failed. Replaced all three. The right hand side of the housing needs to be removed to access these parts. Take lots of pictures for reference as it all comes apart, wiring, placement of the various screws, etc. Not an easy... Read more