Kenmore Elite 12762 Parts

Low-friction slide piece that supports moving components in your range or wall oven. Replace worn or cracked glides to restore smooth operation.

This motor support damper sits between the refrigerator's compressor and base to absorb vibration and movement. Replacing a worn damper helps quiet rattles and humming from the back of the cabinet and keeps the compressor properly supported.

• Cushions the compressor to reduce transmitted vibration and noise
• Helps quiet humming, buzzing, or rattling from the lower rear of the refrigerator
• Maintains proper compressor alignment and support on the base pan
• Common signs of wear: increased vibration/noise, a cracked or flattened damper, or noticeable compressor movement when running

• Unplug the refrigerator and pull it forward to access the rear; allow the compressor to cool before working
• Support the compressor to remove load from the mount before loosening hardware
• Replace the damper and tighten mounting hardware evenly without over-compressing the rubber
• Avoid bending or stressing refrigerant tubing; wear gloves and eye protection

This holder assembly is a structural mounting piece that supports and secures an internal component in your appliance. Replacing a cracked or worn bracket helps restore proper alignment and keeps parts stable during everyday use.

• Provides a rigid mounting point for the attached component
• Keeps parts aligned to reduce movement and vibration
• Helps prevent rattling or noise from loose mounts
• Common signs of failure: visible cracks/broken tabs, looseness, or parts that won't stay seated

• Disconnect power and, if applicable, turn off the water supply before service
• Note the orientation of the original part to match fitment
• Reuse existing mounting screws or hardware unless the manufacturer specifies otherwise
• Do not overtighten fasteners; the secured component is fully seated and stable

Fix water pooling under your refrigerator with this drain tube assembly. Replaces cracked or clogged tubes to restore proper drainage. Straightforward repair.

Fix a refrigerator that won't start or hums but doesn't run with this compressor start capacitor. Restores reliable cooling when the compressor fails to start.

Leaking water line connections? This inline tube connector joins two sections of tubing for a secure, leak-resistant seal. Quick 10-minute fix.

Vibration-isolating grommet that mounts between the compressor and chassis. Replace if cracked, worn, or missing to restore proper cushioning.

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.

This is a dual radiant surface element that mounts beneath the glass cooktop on a smooth-top electric range. It provides heat for cooking by radiating energy through the glass surface and can operate at two different diameters for different pot sizes. Replace this element if the burner no longer heats, heats unevenly, only partially lights up, or if you see visible damage such as cracks or burn spots in the coil.

Adapter assembly for oven vent system. Installs in back wall to align vent components. Replace if cracked, broken, or missing to restore proper fit.

Replacement screw for securing panels, brackets, and covers on appliances. Replaces missing, stripped, or damaged screws to restore alignment.

This replacement switch completes the control circuit for a major appliance function, restoring user control and reliable operation. It mounts in the control panel and provides a durable rotary/infinite control interface. What it does:

• Makes or breaks the electrical connection for the corresponding control function
• Restores accurate control when the original switch is worn, intermittent, or unresponsive
• Can cause the related function to not start, stop unexpectedly, or fail to adjust when it fails
• Used in control panels where a rotary/infinite-type switch is required

• One replacement switch

• Disconnect power to the appliance before beginning any repair
• Verify correct switch orientation and secure mounting before reconnecting wiring
• Handle and route wires carefully; match terminal connections exactly to avoid damage

Door stop assembly for bottom-mount refrigerators. Mounts inside the door to control door closing and sealing. Replace if broken, cracked, or missing.

Replace a cracked, broken, or worn refrigerator drawer tray assembly. Restores food storage organization for produce, deli items, and snacks.

Refrigerator not cooling or freezing? A failed compressor stops the cooling cycle entirely. Professional installation required for sealed system work.

Protective burner cap that sits on top of the gas burner head. Replace if cracked, chipped, discolored, or missing to protect the burner assembly.