Kfeg500esso Parts

This wire harness is the appliance's main electrical connector assembly that routes power and signals between components, restoring reliable electrical connections for controls and motors. Use it to replace a damaged, burnt, or broken harness. What it does:

• Carries power and control signals between the appliance's control board, motors, switches, and sensors
• Replaces damaged wiring that can cause intermittent operation, non-responsive controls, or failure to start
• Restores proper connector fit and secure splices to prevent arcing and poor contact
• Helps eliminate issues caused by frayed insulation, broken terminals, or melted wires

• One complete wire harness assembly

• Disconnect the appliance from power (unplug or switch off breaker) before starting any repair
• Compare the new harness to the old one for connector type and routing before disconnecting components
• Route wires along the original paths and secure with existing clips or ties to avoid heat and pinch points

This oven cavity insulation panel helps reduce heat loss and improves temperature stability inside the oven for more even cooking. It replaces worn or damaged insulation that can allow heat to escape or make the exterior hotter than normal. What it does:

• Provides thermal barrier between the oven cavity and outer cabinet to help maintain internal temperature
• Reduces heat transfer that can cause the exterior surfaces to become unusually hot
• Helps prevent excessive heat loss that can affect cooking performance and energy use
• Fits behind the oven liner where original insulation is mounted

• One oven cavity insulation panel

• Disconnect power (and gas, if applicable) before starting any repair
• Handle insulation with gloves; avoid compressing or tearing the material
• Follow the appliance service manual for proper placement and secure mounting

This right-side slide drawer supports and guides the refrigerator/freezer drawer so it opens and closes smoothly, restoring proper alignment and operation. Simple replacement can stop sagging, sticking, or noisy drawer movement. What it does

• Replaces a worn or broken right-side drawer slide to restore smooth sliding and proper alignment
• Helps prevent the drawer from falling, sticking, or binding when opening or closing
• Supports drawer weight and ensures even movement along the rail
• Works with the existing left-side slide and drawer assembly to maintain fit and seal

• One right-side slide drawer

• Disconnect power to the appliance or remove food and secure contents before service
• Remove the drawer per your model's service instructions to access and replace the slide
• Retain original fasteners and match orientation (right-side) during reassembly
• If you encounter damaged mounting clips or screws, replace them before finishing reassembly

The Surface Element is an OEM part for Whirlpool ranges. It is responsible for providing the heat necessary for cooking on the stovetop. Designed to fit seamlessly into the range, this element ensures even heating and efficient energy use, allowing for precise temperature control during cooking.

Causes of a bad surface element can include normal wear and tear, electrical faults, or damage from cookware. Over time, repeated heating and cooling cycles can cause the element to degrade, while physical impacts or spills can also lead to malfunction.

Symptoms of a bad surface element include:

• Inconsistent or uneven heating
• The element not heating up at all
• Visible damage or burn marks on the element
• Sparks or unusual noises when the element is turned on

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Note: 3000/1400W - Left front element

This spacer provides a precise gap for proper alignment and clearance between components, helping maintain correct part positioning for reliable operation. It's a simple replacement that restores intended spacing and reduces wear. What it does:

• Positions and separates adjoining parts to maintain correct clearance
• Helps prevent rubbing, misalignment, or binding of moving components
• Restores factory spacing after maintenance or part replacement
• Fits where the original spacer was used to support assembly alignment

• One spacer as shown

• Inspect surrounding components and mounting surfaces for damage before installing
• Remove power to the appliance and follow manufacturer service instructions
• Install in the same orientation as the original spacer and verify proper clearance
• If fasteners or adjacent parts are worn, replace them to ensure a secure fit

This glass bracket secures the oven/microwave door glass, keeping the inner glass panel aligned and stable for safe operation. It replaces worn or damaged brackets to restore proper door fit and reduce rattling. What it does:

• Secures and supports the door's inner glass panel to maintain alignment
• Prevents glass movement that can cause vibration, noise, or improper sealing
• Helps restore proper door closing and even heat retention when functioning parts are present
• Commonly replaced when bracket is cracked, bent, or missing mounting integrity

• One glass bracket

• Disconnect power to the appliance before beginning any repair
• Handle glass carefully; wear cut-resistant gloves and eye protection
• Installation typically requires partial door disassembly and removal of retaining screws—keep track of fasteners

This outer door trim restores the finished appearance of an appliance door and covers the edge gap between the door panel and console for a clean, factory look. It helps protect the door edge from everyday wear. What it does:

• Covers and finishes the outer edge of the appliance door for a seamless appearance
• Helps prevent dirt and moisture from collecting at the door edge
• Restores cosmetic damage like scratches, dings or missing trim pieces
• Useful when replacing a cracked, warped or broken door trim piece

• High-level replacement only; remove and reinstall the outer door panel to access the trim
• Use appropriate screwdrivers and keep fasteners organized for reassembly
• Disconnect power (or gas) and follow manufacturer's safety steps before beginning service
• If trim is clipped in, carefully release retaining clips to avoid breaking adjacent parts