Kgrt607hb54 Parts

This spark switch and harness assembly replaces a worn or damaged ignition switch and its wiring to restore reliable sparking for gas burner ignition. It provides the switch contacts and connectorized wiring needed for the cooktop ignition circuit. What it does

• Sends the ignition spark signal when a burner control is turned, allowing the burner to light.
• Replaces a faulty switch or frayed harness that can prevent sparking or intermittent ignition.
• Helps eliminate symptoms such as no spark at the burner, weak or inconsistent ignition, or control knob ignition failure.
• Matches OEM connector and terminal layout for direct replacement where specified.

• Disconnect electrical power and shut off gas supply before starting repair; follow all safety precautions.
• Handle connectors and terminals carefully to avoid bending pins or damaging insulation.
• Basic hand tools are typically required; refer to your model's service instructions for panel removal steps.

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

Kit includes four knobs.

This factory screw secures panels, brackets, or trim within your appliance. Replacing a missing or stripped fastener restores a tight fit, reduces vibration and rattles, and helps keep components aligned for reliable, long-term performance.

• Fastens panels, brackets, or trim to the appliance cabinet/frame
• Replaces damaged, rusted, or missing hardware
• Helps eliminate vibration noises, gaps, and loose-fitting parts
• Supports proper alignment of adjoining components

• Disconnect power; turn off gas/water supplies where applicable.
• Match to the original screw from your model's parts diagram before installation.
• Start threads by hand to avoid cross-threading; use the correct driver bit for the head.
• Tighten snugly—do not overtighten to prevent stripping threads or cracking plastic bosses.

This orifice holder secures the gas orifice in the burner assembly so the appliance meters fuel safely and reliably. It restores proper burner alignment and helps ensure consistent flame delivery for safe cooking performance. What it does:

• Holds the gas orifice in the correct position within the burner assembly
• Helps maintain a steady, properly directed flame for even heating
• Can reduce burner misalignment issues and intermittent flame problems
• Works with the valve/orifice assembly to support normal gas flow at the burner

• One orifice holder

• Designed for use with the original burner/orifice assembly; follow OEM diagram for placement
• Turn off gas supply and electricity before servicing; follow all safety precautions
• Use basic hand tools; handle orifice components carefully to avoid damage

Color: White. Size: 13 oz. Spray paint primer. can.

Gas valve shaft seal.

Replacement stringer bolt that secures the appliance's stringer or support rail to the cabinet frame, restoring panel alignment and preventing movement. Use when the original bolt is missing, loose, or damaged. What it does:

• Secures the stringer/support rail to the appliance frame so panels and assemblies stay aligned.
• Helps prevent cabinet or panel movement that can cause rattling or vibration during operation.
• Restores proper alignment when a loose or missing bolt causes misaligned panels or binding doors.
• Simple, direct replacement for a corroded, stripped, or lost fastener.

• Disconnect power before working on the appliance and remove any panels.
• Use the correct-size socket or wrench; hand-tighten, then snug—do not overtighten to avoid stripping threads.
• Inspect mating threads and replace the bolt if heads or threads are damaged; for the correct fastener location.

This orifice holder assembly secures and positions the gas orifice for a G4 burner, ensuring consistent gas flow to the burner for stable ignition and cooking. Designed to replace a worn or damaged holder and restore proper burner operation. What it does:

• Holds the burner orifice in the correct position so gas flows steadily to the burner head
• Helps maintain even flame distribution and reliable ignition
• Can resolve symptoms like weak or uneven flames, intermittent ignition, or burner misalignment
• Works as the mounting interface between the orifice and burner components

• Turn off gas supply and power to the appliance before beginning any service
• Handle components carefully; confirm proper seating and alignment of orifice and burner before testing
• After installation, check for gas leaks and proper ignition at low and high flame settings

Size: 10-24 x 3/8 inch.

Rubber bumper. Color: Grey.

Size: 10-16 x 1 1/2 inch.

Bottle with brush. Color: New avocado. Size: 0.6 fl.oz.

Size: 10-16 x 3/8 inch.

Locaction: Left front. 14,000 BTU.