Kgss907sss Parts

Replace your cracked, dented, or worn 30-inch oven door panel. This outer skin restores appearance and supports the handle, glass, and trim assembly.

Replacement hinge that supports and pivots your oven door. Install when hinge is broken, worn, or causing door to sag, slam, or leave gaps around the seal.

This fixed thermostat switches near 60C to control a heat-managed circuit—often the oven's cooling/blower fan. Replacing a failed unit restores proper fan cycling and helps protect the control area from excessive heat during and after cooking.

• Monitors temperature in the oven cabinet/control area and switches power based on heat level
• Cycles the cooling/blower fan on and off to manage cabinet temperature
• Helps safeguard electronic controls from heat buildup
• Failure may cause symptoms such as a fan that won't run, a fan that runs continuously, or an unusually hot control area

• Disconnect power at the breaker before servicing
• Access the thermostat per your model; it is typically mounted to a plenum or bracket near the oven cavity
• Move wires one at a time and mount the new thermostat flat against the surface for accurate sensing
• Restore power and verify the fan cycles during operation

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This broiler pan is the heat-safe tray used for broiling in the oven or broiler drawer. Replace a rusted, warped, or missing pan to maintain safe broiling and simpler cleanup by catching drippings.

• Holds food for broiling and supports correct placement under the broiler
• Collects drippings to help reduce flare-ups and smoke
• Restores safe use when the original pan is rusted, pitted, dented, or warped
• Seats on the designated rails/supports in the broiler drawer or compartment per model design

• Allow the appliance to cool completely; wear cut-resistant gloves
• Remove the broiler drawer or open the broiler compartment as your model requires
• Position the pan on the proper rails/supports and verify stable seating before use
• Follow your model's user guide for broiling setup and care

Replacement hex nut for dryer terminal blocks and electrical connections. Secures terminal components. Needed when original is stripped, missing, or damaged.

Replacement broiler pan for ranges and ovens. Holds food under high heat while collecting drippings. Order if your pan is missing, warped, or damaged.

Hex head sheet metal screw secures appliance panels, brackets, and trim. Replace missing, stripped, or damaged screws to keep covers firmly attached.

This orifice holder serves the gas surface burner position designated TCB. It directs gas from the valve to the burner and provides a stable mount for the igniter and burner head to maintain reliable ignition and flame performance.

• Routes gas from the manifold/valve through the orifice to the burner head
• Supports proper alignment of the burner head and cap
• Provides mounting point for the surface igniter/electrode
• Failure symptoms include a burner that won't light or is slow to ignite, weak or uneven flame, or igniter clicking without ignition on that burner

• Disconnect power and shut off the gas supply before servicing
• Allow the cooktop/range to cool completely
• Remove burner cap and head; lift top as required. Transfer the brass orifice and igniter/electrode from the old holder if applicable, then install the new holder
• Reassemble, restore gas/power, and check all connections for leaks with a soap solution. Verify proper ignition and flame

Replacement 8-32 x 3/8 mounting screw for securing panels, brackets, and covers to appliance frames. Restores tight fit when original is missing or worn.

Fix an oven that overheats or won't heat properly. This high-limit thermostat monitors temperature and shuts off power if the cavity gets too hot.

Fix an oven that won't turn on or has a dead control panel. This control transformer steps down line voltage to power the controls and displays.

Color: Citrine white. Size: 4.5 oz. can. Acrylic appliance aerosol can spray paint.

This wire harness connects the control/switch assembly to the appliance's thermal cutoff and control circuits, restoring reliable electrical connections for proper operation. It's a direct-fit replacement when the original wiring is damaged or corroded. What it does:

• Provides the factory routing and connectors between the control/switch and TCB/thermal cutoff
• Re-establishes lost or intermittent power caused by damaged wiring or broken terminals
• Helps stop failures that cause controls to be unresponsive or cycles to stop unexpectedly
• Uses OEM-style terminals and insulation to match original fit and function

• One wire harness (switch TCB) as shown

• Disconnect power before starting — verify the appliance is completely de-energized
• Take photos of existing wire routing and connector locations to ensure correct reassembly
• Plug connectors fully and secure the harness along original clips or tie points; avoid sharp edges
• If terminals are damaged at mating parts, inspect and replace those components rather than splicing connectors

This bake burner is the oven's main gas heating element for baking and roasting—replacing a worn or damaged burner restores proper oven heat and more consistent cooking results. Fits compatible gas wall and range ovens. What it does

• Provides the concentrated flame for the oven's bake function to heat the cooking cavity
• Restores normal baking temperatures when the original burner is warped, cracked, or rusted
• Can help eliminate uneven baking or failure to reach set temperature caused by a damaged burner
• Works with the oven's ignition system; burner does not include igniter unless listed separately

• One oven bake burner

• Disconnect electrical power and shut off the gas supply before beginning service
• Inspect and follow your model's service manual for proper burner alignment and mounting
• After installation, check for proper ignition and flame pattern; perform a gas leak check before use