Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The surface burner orifice holder is a brass or metal fitting that threads into the gas valve and holds the orifice, which is the small precisely sized opening that controls how much gas flows to a cooktop burner. Together with the orifice, it regulates flame size and ensures proper combustion. Replace this part if a burner produces an uneven, weak, or oversized flame, or if the holder is damaged, corroded, or leaking gas at the burner connection.
Ordered a replacement holder with a new ceramic igniter and installed it. The new unit would not quite fit correctly on the Metal stand. It took only a couple of minutes with a large file to remove some of the metal on each side of the metal prongs that locate the holder onto the stand. Once done, it was an easy assembly job and works just fine. Note: I ordered two of the Torx screws along with the holder and discovered this is a necessity since the old stainless screws have a barrel... Read more
This ground screw secures the appliance's grounding wire or strap to the chassis or terminal area, creating a reliable bonding point. Replace a missing or damaged screw to restore a proper ground connection during installation or service.
New hinges solved the problem! FYI the mounting holes were not tapped for screws, I was able to self tap but glad I bought new screws. Read more
Left side hinge receiver for door hinge. For right side hinge receiver use WP4455606.
I was able to order new hinge receiver brackets for the door. The repair was not that bad. I just had to take off the lower door, take the two trim pieces off the sides and unscrew the screws holding the oven into the face of the cabinet. Then slide it out about halfway and put a step stool under the front to keep it from tipping over. Then it was just a matter of taking off everything around the sides until I could take the brackets off, put the new brackets on, and put everything back... Read more
Door hinge receiver for wall ovens. Mounts inside the oven frame to hold the door hinge in place. Replace if cracked, deformed, or causing door alignment issues.
Oven light won't turn on? This light transformer steps down voltage to power your oven cavity lights. Moderate DIY repair restores illumination.
Studied schematics and watched many on-line videos. Did some electrical checks with VOM (Volt/Ohm Meter). Determined that control panel thermal fuse attached to back of control panel had opened due to high temp. Determined that the upper oven thermal fuse on back of oven had opened due to high temp. Determined that transformer that supplies power to lights was bad (open primary). Removed control panel circuit board and had it repaired/verified good. Faulty control panel was the reason that oven... Read more
Fixes dim, flickering, or unreadable oven display screens. Restores clear clock and temperature readouts on your control panel. Direct replacement.
Kit of 4 pins that insert into oven door hinges to safely remove the door for repairs or cleaning. Replace lost or damaged pins during door removal.
I have a 10 year old Kitchenaid double oven with warming drawer below and electrical connection is located in cabinet below. I order a service manual from http://www.allrepairmanuals.com. If you have the service manual follow it, it walks a technician thru each step. If you don't have a manual here are a few highlights. Disclaimer the following is for my oven model KEBS208DBL8, your oven service steps may vary. IMPORTANT! First step turn-off the power to the oven (mine was a 40 amp breaker)... Read more
A factory screw with 8-32 machine threads used to secure brackets, panels, and internal components where specified. Restores a solid, factory fit when the original fastener is missing, stripped, or corroded. What it does:
This factory fastener secures appliance panels, brackets, and internal components so everything stays aligned and quiet. Replacing a missing or damaged screw restores a tight fit and helps reduce vibration, rattles, and wear.
The plastic piece on the handle where the screw goes in to hold glass door up had broke. I ordered new handle, the retainer pieces that go over the plastic pieces to lock it all in and screws that were suggested. The screws were the wrong ones. They were way too small. I already had one screw and thankfully only had to buy 1 new one because the screw was $40 and shipping’s $10 for it AND it’s on back order right now. The old retainer ring that goes over plastic piece was a nightmare to remove... Read more
Replace your cracked, dented, or worn 30-inch oven door panel. This outer skin restores appearance and supports the handle, glass, and trim assembly.
If your oven control flickers or resets randomly, the transient suppressor may have failed. This part protects the control board from power surges.
Replace a cracked, broken, or missing control knob on your gas range. Installs on the control shaft to restore manual adjustment of burner settings.
Replace the knob. Read more
Oven won't heat properly or overheats after self-cleaning? A faulty lower thermostat often causes temperature regulation issues. Moderate DIY repair.
I was devastated to hear my wife tell me our Whirlpool double oven was dead after she used the self clean mode. After my research, I found this problem to be more common than expected. I kept seeing reference made to Appliance Parts Pros during my research. I went to the website and found the parts I didnt think anyone had. APP was quick, the price was excellent and when I called their staff I found them to be friendly, knowledgeable and thorough! They had my parts to me in no time and I fixed... Read more
Replacement broiler pan for ranges and ovens. Holds food under high heat while collecting drippings. Order if your pan is missing, warped, or damaged.
I did not have anything repaired. I ordered a broiler pan for our new Whirlpool Stove. Everything went really well. It even arrived early. We could not be more pleased. It was exactly what she wanted!!! Read more
Replacement hex nut for dryer terminal blocks and electrical connections. Secures terminal components. Needed when original is stripped, missing, or damaged.
Replaced it with the video listed..Maytag Atlantis dryer was not heating. Checked all components inside dryer, thermostat, coils, etc. All check out ok ......last thing I checked was the terminal. It was burned out. Quick video on your website was awesome! THANK YOU for the service, and the ease of ordering parts. LOVE THIS SITE! Read more
Hex head sheet metal screw secures appliance panels, brackets, and trim. Replace missing, stripped, or damaged screws to keep covers firmly attached.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.