Kp2671xwh Parts

This screw secures appliance panels, brackets, and trim so everything stays aligned and rattle-free. Replace missing, stripped, or rusted hardware to restore a solid fit and dependable operation. What it does:

• Fastens components to the cabinet/frame to maintain proper alignment
• Helps prevent vibration, rattling, and small gaps from loose hardware
• Replaces lost, damaged, or corroded screws to restore secure mounting
• Common signs include loose panels/trim, vibration noises, or shifting parts

• 1 screw

• Disconnect power; shut off gas/water if applicable before servicing
• Support the part being fastened to keep holes aligned and avoid damage
• Start threads by hand to prevent cross-threading; realign if resistance is high
• Tighten snugly—do not overtighten to avoid stripping threads or cracking plastic

This retaining ring snaps into a groove to keep a component securely positioned on its shaft. Replacing a bent or missing ring restores proper fit and helps stop looseness, shifting, and noise from parts moving out of place.

• Locks into a machined groove to secure gears, shafts, or linkages
• Prevents axial movement that can cause wobble or separation
• Helps eliminate rattling, scraping, or intermittent operation from loose assemblies
• Direct replacement for a worn, stretched, or missing ring identified during service

• Disconnect power and allow all moving parts to stop before servicing
• Wear eye protection; retaining rings can spring free under tension
• Use proper snap-ring/retaining-ring pliers and avoid over-expanding the ring
• Ensure the ring is fully seated in the groove with correct orientation and retention

This planetary assembly restores the mixer's planetary mixing action by linking the gearcase to the beater shaft. It replaces a worn or damaged lower hub to deliver smooth, consistent attachment rotation. Finish: imperial gray.

• Drives the beater/attachment shaft with true planetary motion
• Transfers power from the internal gear train to the attachments
• Helps maintain proper alignment of the lower hub
• Resolves: beater not turning, slipping, grinding/clunking from the front, or visible wobble/damage at the planetary hub

• Disconnect power; remove bowl and attachments before service
• Protect the finish; remove the drip ring to access the retaining pin
• Drive out the planetary retaining pin, slide off the old assembly, and align/install the new one
• Seat the pin fully and verify smooth rotation before reassembly and testing

This 8-32 x 5/8 screw replaces missing or damaged hardware specified by the manufacturer to secure panels, brackets, and internal components in your appliance. Restores a tight, rattle-free fit to help prevent vibration and misalignment.

• Provides the correct 8-32 thread and 5/8-inch length where specified
• Secures sheet-metal panels, brackets, and internal assemblies
• Replaces missing, stripped, or corroded screws
• Symptoms include loose or rattling panels, misaligned parts, or hardware that won't stay tight

• Disconnect power; shut off gas before servicing
• Support panels/components while removing or installing hardware
• Start threads by hand to avoid cross-threading; tighten only until snug
• Match the original screw's location and orientation for proper fit

This spring-style roll pin secures mating parts on a shaft or linkage. It keeps components tightly aligned so gears, levers, or hubs stay in place during operation, helping prevent looseness, slipping, and noise.

• Expands inside aligned holes to lock components together on a shaft or hub
• Helps maintain alignment and transmit torque in rotating or linkage assemblies
• Common failure signs: wobble, rattling, parts shifting out of place, or intermittent operation
• Replace if the original pin is bent, cracked, sheared, missing, or no longer holds a tight fit

• Disconnect power and work on a stable surface with the appliance cool
• Support the assembly; use a correctly sized roll-pin punch and light hammer taps to drive the old pin out
• Align holes carefully and press/tap the new pin in flush; do not enlarge the hole
• Wear eye protection and avoid striking cast or plastic parts directly

Pouring Shield For 5 and 6 Quart KitchenAid Lift Bowl Stand Mixer Bowls. The one piece pouring shield is attached to the mixing bowl and helps with adding ingredients without making a mess by keeping lightweight ingredients like flour from flying out of the bowl while mixing. The Pouring Shield is dishwasher safe on the top-rack and works with KitchenAid models KB26G1, KD2661, KL26M2, KL26M8, KP2671, KP26M1, KP26M8, KP26M9, KP26N9, KSM7581, KSM7586, KSM7588, KSM7589, KT2651, KV25H, 4KB25G, 4KD2661, 4KP26M1, 5KSM7580, 5KSM7581, 5KSM7586, 5KSM7590, 5KSM7591, 7KSM7586, 9KSM7990.

This small retainer clip secures the drip bowl and coil surface element so they stay properly seated on the cooktop. Replacing a worn or missing clip restores a tight, level fit and reduces wobble during use. What it does:

• Holds the drip bowl to its mounting point and helps keep the surface element seated
• Maintains alignment to reduce movement and rattling
• Helps prevent the element from tilting so cookware sits more evenly
• Common symptoms: loose or wobbly burner/bowl, bowl won't stay seated, or a cracked/missing clip

• Retainer clip only

• Disconnect power at the breaker before servicing
• Lift out the coil element and drip bowl; note clip orientation for reassembly
• Snap the new clip into place carefully—avoid over-flexing the part
• Reinstall the bowl and element and ensure the burner locks in and sits level

This factory mounting screw secures components in place inside compatible appliances, helping maintain proper alignment and reliable operation.

• Fastens panels, brackets, or internal parts to prevent shifting and vibration
• Common fix when a panel or bracket is loose or rattling
• Resolve issues like gaps, misalignment, or buzzing from loose hardware

• Unplug power and shut off utilities before servicing
• Retain and reuse original hardware and clips where applicable
• Start threads by hand to avoid cross-threading, then tighten snugly without over-torquing

Replacement cam that restores proper engagement of the appliance's mechanical linkage so cycles run smoothly. Installs where the drive/shift mechanism needs a correctly timed cam to stop slipping or misalignment. What it does:

• Transfers rotary motion to the linked component so parts engage at the correct time
• Restores reliable engagement to reduce skipping, grinding, or irregular cycle behavior
• Commonly replaced if cracked, worn, or otherwise fails to engage properly
• Matches the OEM part name and fit as a direct replacement when the original cam is damaged

• Always disconnect power (and water, if applicable) before starting service
• Remove required access panels and note the original cam orientation for correct reassembly
• Inspect mating parts (shaft, clips, splines) and replace any damaged hardware before installing the new cam
• Reassemble panels and run a test cycle to ensure normal operation and correct engagement

The Rotating Handle is an OEM part for Whirlpool mixers. It allows you to raise and lower the mixing bowl for convenient access during the mixing process.

A bad rotating handle can be caused by regular use, accidental damage, or excessive force applied during operation. If you notice cracks, a loose or wobbly fit, or difficulty in rotating the handle smoothly, it may indicate a problem with the handle itself.

Symptoms of a bad rotating handle include:

• Cracked or damaged handle surface
• Loose or insecure fit of the handle on the mixer
• Inability to raise or lower the mixing bowl 

Replace your faulty handle with this genuine OEM part to restore your mixer. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This factory replacement screw fastens appliance components securely. Use it to replace lost, stripped, or corroded hardware and restore a snug, rattle-free fit and proper alignment of panels and assemblies.

• Secures panels, brackets, and internal components to their mounting points
• Replaces missing or damaged fasteners to maintain correct alignment
• Helps eliminate vibration and rattling caused by loose hardware
• Restores the original fit with OEM-matched threads and dimensions

• Disconnect power and shut off water or gas supplies before servicing
• Use the correct driver bit that matches the screw head to avoid stripping
• Replace one fastener at a time to keep parts aligned
• Tighten snugly; do not overtighten to prevent stripped threads or cracked plastic

This 6-32 machine screw is a direct-fit fastener used to secure appliance panels and components. It provides a reliable replacement for stripped or missing screws to restore proper fit and reduce vibration or looseness. What it does:

• Secures panels, brackets, and internal components to keep parts aligned and stable
• Restores proper fastening when original screws are missing, stripped, or damaged
• Helps eliminate rattling or movement caused by loose fasteners
• Compatible with metal-to-threaded-hole connections that use 6-32 hardware

• Use the correct driver and avoid over-tightening to prevent stripped threads or damaged components
• Disconnect power and follow appliance safety guidelines before servicing
• If threads are damaged, replace both screw and any damaged insert or nut as needed

Cap Hub covers and protects the appliance's hub, restoring a finished appearance and helping keep debris away from internal components. Use when the original hub cap is cracked, missing or visibly worn. What it does:

• Covers and conceals the drive/tub hub for a finished look.
• Helps keep lint and debris away from the hub area.
• Replaces cracked, broken or missing hub caps that expose the hub.
• Check the model-specific diagram for exact fit and orientation.

• Disconnect power (and water if applicable) before beginning any service.
• Part typically snaps or presses into place; the appliance's exploded diagram for the correct removal/replacement procedure.
• Do not force the part; inspect surrounding components and replace any damaged mounting hardware as needed.

Upgrade or replace your mixer's paddle with this coated flat beater in Silent Silver. It restores smooth, even mixing performance for everyday recipes and is designed in the narrow profile specified for select stand mixers.

• Blends ingredients thoroughly for batters, doughs, and mashed mixtures
• Direct replacement for a beater that is bent, chipped, peeling, or missing
• Narrow profile mates correctly with the intended mixer hub style

• Unplug the mixer before attaching or removing the beater
• Tilt the head up or lower the bowl; align the beater slot with the shaft pin, push up, and twist to lock
• Clean and dry per the manufacturer's care instructions before first use

The Power Cord is an OEM component specifically designed for Whirlpool stand mixers. Located at the rear base of the mixer, it safely delivers current to operate mixing attachments, speeds, and functions. 

Causes of a bad power cord include cracking or pulling at the entrance/exit points over years of use. Acute damage like punctures or burns requires replacement.

Symptoms of a faulty power cord include:

• Loose, interrupted connections when plugged in  
• Exposed or frayed internal filaments
• Tripping circuit breakers more frequently
• Buzzing, zapping, or dead mixer response

This OEM Whirlpool replacement cord ensures problem-free current transmission. Installed promptly, it prevents shock risks or fire hazards due to compromised integrity.  

Compatible also with some KitchenAid and Proctor Silex mixers, this part maintains crucial convenience and performance. Protect your valued kitchen tool with an OEM power cord replacement as needed.