Krfc704fss-01 Parts

This electronic control board manages the appliance's functions and user interface, replacing a failed printed circuit board to restore normal cycle control and electronic operation. Fits as the direct replacement for the factory control module. What it does:

• Receives user inputs and sends commands to motors, valves, heaters, and sensors
• Manages timing and cycle selection so the appliance runs intended programs
• Can resolve symptoms like no display, unresponsive controls, cycles not starting, or erratic operation
• Interfaces with touchpads and led/lcd displays to show status and error codes

• Disconnect power before servicing to avoid shock or damage
• Handle the board by the edges and avoid static discharge; use ESD protection if available
• Transfer any user interfaces or harnesses exactly as removed; verify connector seating

This replacement refrigerator door gasket creates a tight seal around the door to help maintain proper temperature and energy efficiency. It restores the door's seal to reduce drafts and help food stay fresher longer. What it does:

• Seals the door edge to prevent cold air loss and reduce frost buildup
• Helps maintain consistent internal temperature for better food preservation
• Reduces compressor run time caused by leaking seals
• Fits around the perimeter of a single refrigerator/freezer door opening

• Inspect the door and mounting channel for damage before installing
• Clean the sealing surface with mild detergent and dry thoroughly prior to fitting
• Warm the gasket with a hair dryer (low heat) if needed to flex and seat evenly

The Water Filter Housing is an OEM part for Whirlpool refrigerators. It is the plastic housing that holds the refrigerator's water filtration cartridge in place within the unit. The housing ensures that water flows through the filtration cartridge as intended before being dispensed through the refrigerator door.

Causes of a bad housing can include cracks, leaks, or damage that compromise its ability to properly contain the filtration cartridge. Mineral buildup over time may also cause issues.

Symptoms of a bad housing include:

• Water not flowing through the dispenser
• Leaks around the water filter area
• Mineral deposits near the housing
• An ill-fitting or loose filtration cartridge

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This is a replacement mounting/support bracket that secures internal appliance components and restores proper alignment for panels and assemblies. Replaces a worn or damaged bracket to reduce movement and restore stable operation. What it does:

• Provides a secure anchor point for panels, trim, or internal assemblies
• Prevents sagging, rattling, and misalignment caused by a broken or weakened bracket
• Helps maintain proper spacing and fit between parts to reduce noise and wear
• Commonly replaced when visible cracking, bent metal, or loose attachment is present

• One mounting/support bracket

• Disconnect power to the appliance before attempting any repair
• Verify bracket orientation and fit against the appliance before fastening
• Use appropriate hand tools and retain all fasteners; do not overtighten

This insul-sound deadening pad reduces vibration and noise by dampening panels and components in laundry and kitchen appliances. It's a small adhesive-backed sound/isolation pad used where noise or rattles transfer through metal surfaces. What it does

• Dampens rattles and reduces structure-borne noise from panels, cabinets and housings.
• Helps isolate vibrating components from appliance chassis to lower perceived sound.
• Commonly applied behind control panels, cabinet walls or on motor mounts to cut vibration transmission.
• Useful when worn, detached or hardened factory pads allow increased noise.

• One insul-sound deadening pad

• Disconnect power before servicing an appliance to avoid shock or injury.
• Clean and dry mounting surface; press pad firmly to ensure adhesive contact.
• Replace only in the original location; do not cover vents or moving parts.
• If adhesive is weak, use OEM-approved adhesive; avoid solvents that may damage finishes.

This sealed refrigeration compressor restores the refrigerant compression stage that circulates coolant and enables proper cooling in compatible refrigerators. Replace a failed compressor to address loss of cooling and related compressor symptoms. What it does:

• Compresses refrigerant to maintain the refrigeration cycle and cold temperatures
• Commonly needed when the refrigerator runs but fails to cool or cools poorly
• Replace a compressor that hums loudly, overheats, or causes frequent tripping of breakers
• Works as the sealed motor/pump assembly within the fridge refrigerant system

• Replacement typically requires recovery of refrigerant and recharging
• Disconnect power and unplug the appliance before starting any work
• Use manufacturer torque and mounting procedures during installation
• Follow all local codes and safety practices for handling refrigerants and sealed-system repairs

This terminal block cover protects the appliance's power connection area and helps prevent accidental contact with live terminals. It keeps wiring organized and shielded for safer operation. What it does

• Shields the appliance's power terminal block from accidental contact and debris
• Helps keep terminal connections secure and wiring routed neatly
• Reduces risk of shorting at the power connection area
• Commonly replaced when the original cover is cracked, broken, or missing

• Disconnect power to the appliance before attempting any service
• Remove access panels as needed to reach the terminal block, then snap or screw the cover into place per the appliance's wiring layout
• If terminals or wires are damaged, replace or repair connectors before installing the cover