Ksm150psb Parts

Protects your mixer shaft from wear and metal-on-metal contact. Replace when you notice rubbing noise or rough operation. Verify fit with your model.

Fix grinding noise and poor mixing with this planetary assembly. Restores drive alignment for smooth mixer operation. Moderate DIY repair for most users.

Fix a mixer that won't change speeds or is stuck on one setting. This speed selector lever restores fingertip control. DIY-friendly repair.

Cobalt blue cover that restores your mixer's exterior appearance. Replaces the original panel when it's cracked, faded, worn, or missing.

This direct-drive gearcase converts the washer motor's power into the agitation and spin motions. Replacing a worn gearcase restores normal drive function so the washer can agitate and spin as intended. What it does

• Transfers motor rotation to the agitator and spin basket for wash and spin cycles
• Worn or damaged gear teeth can cause no agitation or no spin
• Damaged gearcase may produce loud grinding, clunking, or unusual noises during operation
• Failure can cause intermittent drive or loss of drive in one or both cycles

• Disconnect power and water before starting any repair to prevent shock or flooding
• Drain the washer and secure the tub/agitator before removing components
• May require removing the cabinet or access panels and supporting the drum during service

A 10-24 lock nut used to secure threaded fasteners and prevent loosening from vibration. Simple, durable replacement that restores proper fastening where the original nut has worn or failed. What it does:

• Secures shafts, studs, or bolts with 10-24 threads and resists loosening under normal appliance vibration.
• Restores proper tension where a stripped or loose nut causes rattling or parts shifting.
• Helps maintain alignment of panels, brackets, or components that rely on a locked fastener.
• Small hardware solution for common fastening failures—no special part modifications required.

• Disconnect appliance power and water before beginning repairs.
• Use the correct 10-24 threaded fastener and a properly sized wrench or socket to avoid rounding the nut.
• Tighten to a snug fit—do not overtighten or force onto damaged threads.
• Inspect mating threads and replace the bolt/stud if threads are stripped or damaged.

Replace the end cover on your stand mixer when the original is cracked, broken, or missing. This cosmetic panel installs on the motor housing end.

This lever latch is the replacement latch used to secure and release the appliance door or access panel, restoring proper door engagement and user operation. It fits the OEM latch location and matches the original white/storm-gray finish. What it does:

• Replaces a broken, cracked or worn latch lever that prevents the door from closing or latching securely
• Restores smooth open-and-close action for the affected door or panel
• Prevents rattling or misalignment caused by a damaged latch
• Matches the original finish to maintain the appliance appearance

• One lever latch (white/storm-gray), as shown

• Disconnect power to the appliance before beginning any repair
• Remove the damaged latch and install the replacement using the factory mounting points; fasteners or clips may be required depending on model
• Handle small plastic parts carefully to avoid breakage during installation
• Refer to your model-specific parts diagram or service manual for exact removal and reassembly steps

5 quart flex edge beater attachment for stand mixers. Replaces worn, cracked, or missing beaters. Flexible edge scrapes bowl sides for thorough mixing.

Fixes mixer that won't start, stops under load, or runs weak. This motor armature restores full speed and power when the rotor assembly fails.

Fix mixer wobbling or grinding noises with this planetary gear assembly. Essential for smooth mixing action. Moderate repair with periodic greasing.

Fix a stand mixer that won't start, runs weak, or makes grinding noises with this armature motor rotor. This rotating core restores motor power.

Fastens panels and internal components in stand mixers. Replace if the original screw is missing, stripped, or damaged to restore secure assembly and fit.

White center cap that covers the hub on your stand mixer bowl. Replaces cracked, broken, or missing caps to restore appearance and protect hardware.

Replacement access panel cover for stand mixers. Shields internal wiring and controls while restoring exterior appearance. Replaces cracked or missing covers.