Kss48 Parts

Left hand side

This is a replacement wire harness that restores electrical connections between components so your appliance powers and controls operate correctly. It provides the factory-style wiring needed for reliable signal and power routing. What it does

• Carries power and control signals between major components so circuits can operate as intended
• Commonly used when damaged, melted, cut, or corroded wires cause intermittent operation or loss of function
• Can resolve symptoms such as components not receiving power, control buttons or lights not responding, or erratic behavior due to open/shorted wiring
• Matches OEM routing and connector ends to maintain original fit and connections

• One complete wire harness assembly as shown

• Disconnect all power (unplug or shut off breaker) before starting any repair
• Note wire routing and connector locations or take photos before removal to ensure correct reassembly
• Inspect connectors and mounting clips; replace any broken retainers to prevent chafing or strain

A roll pin (spring pin) that secures rotating or sliding components by fitting into matched holes to hold shafts, levers, or brackets in place. Replaces a worn or damaged pin to restore proper mechanical engagement. What it does:

• Holds shafts, levers or hinges in position by expanding into drilled holes for a snug, vibration-resistant fit
• Keeps pulleys, rollers, or linkages from moving out of alignment or sliding off their shafts
• Common symptom: loose or wobbling pulley, lever, or shaft where the retaining pin is worn or broken
• Common symptom: noisy or intermittent operation caused by a pin that no longer secures moving parts

• Inspect mating holes and shaft for wear; replace pin with correct size to ensure secure fit
• Use appropriate pliers or a pin punch and hammer to drive the pin in or out; support the assembly to avoid damage
• Wear eye protection when installing or removing roll pins—pins can snap or fly out under force
• If pin is difficult to remove or install, consider using penetrating oil or heating only per OEM guidance

This ejector arm replaces the dispenser ejector that helps move detergent or rinse aid from the dispenser to the wash chamber for proper release during the cycle. Restores reliable dispensing and prevents missed or partial releases. What it does:

• Physically pushes or guides detergent/rinse into the wash chamber at the correct point in the cycle
• Replaces cracked, broken, or worn ejector arms that fail to move or sit correctly
• Addresses symptoms such as detergent not dispensing, dispenser door sticking, or visible damage to the ejector arm
• Works with the dispenser assembly to ensure consistent product release during operation

• Disconnect power to the appliance before starting any repair
• Remove the dispenser assembly per the service manual to access and replace the ejector arm
• Inspect surrounding dispenser components (hinges, springs, clips) and replace if damaged

Color: White. Size: 1 qt. can. Acrylic appliance paint.

This heat exchanger assembly directs and isolates the dryer's heating airflow, helping the dryer heat and operate safely. It replaces a damaged or corroded exchanger to restore proper airflow routing and reduce heat loss. What it does:

• Channels heated air through the dryer's heating system for efficient drying performance
• Protects surrounding components by containing and directing heat away from sensitive parts
• Can help address symptoms like reduced or uneven heating, persistent burning or scorched odors, or visible damage/corrosion to the exchanger
• Works as the OEM-design replacement to restore correct airflow routing in the heater area

• One heat exchanger assembly

• Follow manufacturer service manual instructions; disconnect power (and gas if applicable) before starting service
• Inspect surrounding seals, gaskets, and mounting hardware; replace any damaged components for best results
• Handle with care—sharp edges may be present; use gloves and eye protection

This egg carrier is a molded tray that holds and secures eggs inside the refrigerator so they stay organized and protected from rolling or breaking. It restores safe, tidy egg storage and fits the factory shelf location. What it does

• Holds and stabilizes eggs on the refrigerator shelf to reduce rolling and breakage.
• Replaces cracked, warped, or missing egg trays that allow eggs to shift or rattle.
• Restores the original storage configuration for proper fit and clearance.
• Simple, low-profile design keeps eggs accessible while maximizing shelf space.

• Disconnect power or open fridge and work in a well-lit, dry area; handle eggs and shelves carefully.
• Remove existing tray by lifting or sliding per shelf design; align new carrier with shelf supports and seat fully.
• No special tools required for most installations; inspect shelf area for damage before installing.

This replacement bracket secures the refrigerator ice maker assembly so it stays properly positioned for reliable ice production. It restores stable mounting and helps prevent the ice maker from shifting or coming loose. What it does:

• Holds the ice maker assembly in place on the freezer liner or mounting frame
• Keeps the ice maker aligned for proper operation and water fill
• Helps stop vibration or movement that can cause noisy operation or misfeeds
• Useful when the original bracket is bent, broken, or missing

• Disconnect power to the refrigerator and shut off the water supply before starting
• Remove the ice maker to access the bracket mounting screws
• Reuse existing screws if undamaged; tighten to secure but avoid overtightening
• If mounting points or surrounding plastic are damaged, replace or repair before reinstalling

A replacement support control bracket that secures the appliance control/console to the cabinet, restoring stable button alignment and preventing the control panel from sagging or shifting during use. Durable stamped metal design for reliable mounting. What it does:

• Secures the control console to the appliance cabinet so the control assembly stays properly positioned
• Prevents the control panel or console from sagging, rocking, or coming loose
• Helps maintain proper alignment of switches, knobs, and electronic controls
• Resolves intermittent button contact or usability issues caused by a loose console

• Disconnect power before beginning any service to avoid shock or injury
• Basic hand tools (screwdriver, nut driver) are typically required; keep original fasteners if present
• Align bracket with factory mounting points and tighten hardware securely but avoid overtightening