Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix a compactor that won't cycle or has intermittent control with this SPDT rocker switch. Snaps in with finger pressure in about 5-30 minutes.
Verified "solid mode" side of switch was open, ordered new switch. Removal of old switch and installation of new switch is easy, the switch is held in with tabs, finger pressure was enough to allow the old switch to be removed. The new switch then snaps right in. One minor issue I encountered was while the new switch had wire color labels for each contact, I had to swap the two outer leads (orange/black, and yellow) to get the operating mode to match the front panel labels. I'm assuming... Read more
Usually ships within 4 - 14 days
Fix a broken or loose compactor control with this rotary switch knob. Restores easy setting selection when your dial is cracked, worn, or hard to turn.
This latch assembly secures the trash compactor drawer in the closed position and engages the safety interlock that allows the compactor to operate. It mounts to the front of the compactor frame and connects to the door switch mechanism. Replace this part if the drawer will not latch shut, the compactor fails to start because it does not detect a closed door, or the latch mechanism is visibly broken or worn.
This precision thrust race serves as the hardened bearing surface for axial loads in a rotating mechanism. Replacing a worn race reduces friction and noise, helping restore smooth, consistent motion and protect companion thrust bearings and washers from accelerated wear.
I bought new thrust races, a drive gear kit, bearings and a sprocket. When the bearing went out, the thrust races, washers, one bottom plate, and a sprocket was eaten up by the the chain due to the slack being created. I followed the video for the Drive Gear Kit repair and everything went together well. I did have to remove the tracks from inside the compactor in order to remove the cardboard liner that "hides" the drive rods. Additionally, be careful to not over-tension the chain when... Read more
Bag carrier handle assembly for trash compactors. Secures the disposable liner bag in place. Replace if cracked, broken, or missing to restore safe bag handling.
News one installed quick and easy Read more
Metal mounting bracket that secures internal components in your trash compactor. Replace if bent, damaged, or missing to restore stable part alignment.
Drive chain connects the motor to the ram mechanism in your trash compactor. Replace if the chain is broken, stretched, or missing to restore compaction function.
0.6 oz. platinum touch-up paint with brush for appliances. Repairs scratches, chips, and gouges on doors, handles, and trim panels. Acrylic formula.
Secures and supports internal compactor components to keep panels and assemblies aligned. Replaces worn, damaged, or missing brackets for firm installation.
The compactor failed with the ram down, so the drawer wouldn't open which in turn made the mounting brackets inaccessible. This necessitated sliding a thin oscillating saw blade between the cabinet face frame and the counter top to cut through the brackets. It was then possible to roll the unit out and place it on its side. I removed the five screws holding the bottom pan in place, dropped the pan exposing the gear/chain train. The large gear was cracked from shaft out to the edge. One of... Read more
Replacement drawer slide rail for trash compactors. Restores smooth gliding and proper tracking when original is cracked, bent, or worn out.
Replacement leveling wheel for trash compactors and ranges. Installs on the cabinet base to restore smooth rolling and proper leveling adjustment.
This is a right-side metal retainer bracket used to secure the trash compactor in its built-in cabinet opening during installation. It anchors the unit firmly in place to prevent shifting or vibration during compaction cycles. Replace this bracket if it is bent, broken, or missing, which can cause the compactor to move or become unstable during operation.
Pulled out and removed old snapped bracket. Simple repair involving bracket and screwdriver. Read more
Left side frame slide for trash compactors. Replaces cracked, broken, or worn slides that support the compactor drawer. Essential structural component.
Door strike plate for trash compactors. Mounts to cabinet frame to secure the door latch. Replace if cracked, bent, or missing to restore proper closure.
Fix excessive noise or wobbling components in your trash compactor with this wave washer retainer. Secures shaft-mounted parts to prevent movement.
Replacement mounting screw for securing panels, brackets, and components to your appliance chassis. Needed when original screws are stripped or missing.
I ordered extra parts because they were on sale. I also picked up the heating element and thermal Fuse too. The actual problem was the Cycling thermostat opened up on us. It was an easy fix. Its great that you have repair videos on your site. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.