Kudp01fls0 Parts

Color: gray. Measures about 3 inches wide by 1-1/2 inches high.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This hanger anchors the dishwasher's door-balance spring to the frame so the door opens and closes smoothly. Replacing a worn or broken hanger restores proper spring tension and helps prevent a door that drops, slams, or feels heavy.

• Secures the door balance spring to the dishwasher cabinet/frame
• Maintains correct spring tension for smooth, controlled door movement
• Helps fix a door that falls open quickly or won't stay in position
• Useful to replace when door balance hardware shows wear or damage

• Disconnect power and shut off water before servicing; remove the toe panel/kickplate
• Support the door and carefully relieve spring tension before removing parts
• Slide the dishwasher out if needed for side access; transfer the spring to the new hanger and reinstall
• Inspect the opposite-side spring/link and hinge for wear; verify door balance before reassembly

Color: light gray. Measures about 3 inches high by 6 inches deep.

The Rinse Aid Cap seals the dishwasher dispenser's rinse aid reservoir. Replacing a worn, cracked, or missing cap prevents leaks and evaporation, helping the dispenser meter rinse aid properly during the final rinse.

• Provides a tight seal for the rinse aid reservoir
• Helps ensure correct rinse aid dispensing in the final rinse cycle
• Symptoms include: cap cracked or missing; rinse aid leaking or depleting quickly; residue or streaks near the dispenser

• Disconnect power to the dishwasher before servicing.
• Remove the old cap and clean any buildup around the dispenser opening.
• Hand-install the new cap until snug; do not overtighten.
• Fill the reservoir and check for leaks around the cap.

Color: gray. Measures about a 1/2 inch wide by 3 inches high by 1-1/2 inches deep.

This user interface is the electronics behind a full-door console dishwasher panel. It reads your button selections and communicates with the main control so cycles start and options respond reliably.

• Interprets keypad inputs from the console and sends commands to the control board
• Helps restore proper control of wash cycles, options, and start/delay functions
• Common symptoms: unresponsive or intermittent buttons, no console lights, can't start from the panel, erratic beeping/stuck-key behavior
• Built for full-door (full-console) configurations used on select models

• Disconnect power at the breaker; turn off the water supply
• Remove inner door/console screws to access the UI; support the panel to avoid straining wires
• Handle the board with ESD care; transfer any mounting clips/brackets and seat ribbon cables/connectors fully and correctly
• Reassemble the door and test console operation before running a full cycle

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

This control panel mounts on the appliance's door and provides the push-button interface for selecting cycles and options. Replacing a cracked or unresponsive console restores reliable button operation and a clean, factory look. What it does:

• Houses the user-interface buttons and indicator windows used to select cycles/options
• Provides a rigid mounting surface for the door's UI components
• Helps protect internal wiring at the top of the door
• Typical symptoms: buttons don't respond or work intermittently, unit won't start when Start/Resume is pressed, selections change unpredictably, or the console is cracked/loose

• One console assembly

• Disconnect electrical power; turn off the water supply if needed
• Open the door and remove the inner-door perimeter screws to separate the console from the inner panel
• Note and transfer any reusable parts from the old console as required; make secure, straight ribbon/harness connections
• Reassemble the door, restore power, and run a quick function check before final tightening

To order seal use WP8268340.

Almond. Size: 13 oz. can. Acrylic appliance paint.

This run capacitor helps start and keep the motor running smoothly by providing the necessary phase shift and torque boost. A weak capacitor can cause hard starting, humming, or intermittent motor operation.

• Supplies continuous phase shift to maintain motor rotation
• Helps the motor start reliably under load
• Symptoms can include humming, slow or no start, or overheating shutdown
• Restores normal operation when the original capacitor has weakened

• Disconnect power before servicing; discharge the old capacitor safely
• Note wire locations and transfer leads to the new capacitor one-by-one
• Mount securely in the original bracket or location to prevent vibration
• If the motor still won't start, further diagnosis of the motor or start device may be required

Color: Almond

This is the dishwasher upper spray arm that delivers water across the top rack for effective cleaning. It replaces a worn or damaged spray arm to restore proper water distribution and rinse performance. What it does:

• Spins and sprays water across the top rack to help remove food and detergent residue
• Restores proper spray pattern when the original arm is cracked, clogged, or not turning
• Helps prevent poor cleaning, spots, or missed areas on top-rack dishes
• Works with the dishwasher's water delivery system to maintain rinse and wash coverage

• One upper spray arm

• Turn off power and water to the dishwasher before beginning any service
• Inspect and clear any debris from the spray arm and the mounting area before installation
• Hand-tighten or snap the arm into place per your model's instructions; avoid overtightening

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning