Kuds30ixbl Parts

This genuine OEM part is a touchpad control panel assembly for dishwashers. The touchpad control panel assembly is the plastic piece that houses the selection buttons of the dishwasher that control the desired setting of the washer. If the touchpad control panel assembly is no longer responsive to touch, it will need to be replaced.To replace this part, start by turning off the power to the appliance. Then take a screwdriver or putty knife to release the control panel from its locking tabs. Pull up gently to pry the control panel out of its place. Once removed set it to the side, and remove the wire harness and any individual wires that are attached to the control panel. Once removed, place the wires into the new unit in their correct terminals. Snap the new control panel assembly into its proper position and restore power to the dishwasher. This authentic replacement part is sourced directly from the manufacturer and is sold individually. It is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

This cover screw secures an appliance cover or access panel to the cabinet, protecting internal components and reducing vibration. Replace missing, stripped, or corroded screws to keep panels tight and the unit safe and quiet.

• Fastens a cover or access panel to the appliance chassis
• Maintains proper panel alignment and enclosure integrity
• Helps eliminate rattles or buzzing from loose panels
• Typical symptoms: loose/misaligned cover, missing screw, vibration noise

• Disconnect power; for gas/water appliances, shut off supplies before service
• Wear cut-resistant gloves—sheet-metal edges can be sharp
• Align the cover and start the screw by hand to avoid cross-threading
• Tighten snugly; do not overtighten into plastic or thin metal

Color: Black

Color: White

Includes two screws, two clamps, and undercounter mounting brackets.

This insulation pad installs in the factory location to isolate and cushion components or panels. It helps reduce vibration and limit unwanted heat transfer, supporting quieter operation and proper performance where the original pad was installed.

• Provides a thermal and acoustic barrier between parts or panels
• Helps minimize vibration and rattling noises
• Restores proper spacing/cushioning when the original pad is missing or deteriorated
• Replace if the pad is brittle, compressed, contaminated, or falling off
• Common signs include increased noise or rattles and localized hot spots or condensation

• Disconnect power (and gas/water, if applicable) before servicing
• Allow hot or cold surfaces to return to a safe temperature
• Note the original pad's location/orientation; remove old pad and clean the surface
• Install the new pad in the same spot without over-compressing; secure per the original method and verify clearances

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.

Also Order Spray Arm Seal

This factory screw secures panels, brackets, or components within your appliance. Using the correct OEM fastener helps ensure a snug fit and prevents loosening, rattling, or misalignment over time.

• Fastens metal or plastic components to maintain proper alignment
• Helps prevent vibration, noise, and loosened parts
• Common wear item that can strip, rust, or go missing
• Replaces damaged or missing hardware to restore secure mounting

• Disconnect power and shut off water or gas before service
• Note original screw location and orientation for proper reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• If threads are damaged, inspect the mating hole or clip before reuse

This replacement utensil basket holds silverware and small kitchen tools upright in the dishwasher so they stay separated for better cleaning and don't fall through the lower rack. Durable plastic design for everyday use. What it does:

• Holds forks, knives, spoons and small utensils upright and separated for improved wash coverage
• Keeps utensils from falling into the wash area or getting trapped under the rack
• Helps reduce rattling and clumping of cutlery during the cycle
• Useful when the original basket is cracked, broken, or missing

• No tools required; slide or drop the basket into the lower rack in the designated position
• Ensure the lower rack is pulled out enough to seat the basket fully and that it sits flat
• Clean basket with mild detergent; avoid harsh solvents or abrasive pads

This factory wire harness restores safe, reliable electrical connections inside your appliance. It routes power and control signals between the main control and key components so the unit starts, runs, and responds correctly.

• Distributes power and signals between the control board and components such as motors, valves, heaters, switches, and sensors
• Replaces damaged, brittle, burned, or corroded wiring to eliminate intermittent or failed operation
• Helps address symptoms like no power, won't start, dead or flickering controls, specific functions not working, error codes, or a burnt-wiring odor
• Built with matching connectors and lengths for correct fit and routing

• Disconnect electrical power before servicing; wear cut-resistant gloves
• Photograph existing connector locations and wire routing before removal
• Move any model-specific clips or ties to the new harness; keep wiring clear of sharp, hot, or moving parts
• Seat connectors fully until latched; verify strain relief, restore power, and test operation

This replacement screw secures panels, brackets, and other components inside your appliance. Replacing missing or stripped hardware restores a tight, rattle-free fit and keeps parts anchored as designed.

• Fastens metal or plastic panels, brackets, and internal components
• Replaces missing, damaged, or stripped screws
• Helps resolve vibration, rattling, or loose-fitting parts
• Maintains proper alignment and secure mounting points

• Disconnect power and shut off water/gas supplies before service
• Match the screw to its original location; your model's diagram to placement
• Start threads by hand and use the correct driver to avoid stripping
• Do not overtighten, especially into plastic or thin sheet metal

This run capacitor helps start and keep the motor running smoothly by providing the necessary phase shift and torque boost. A weak capacitor can cause hard starting, humming, or intermittent motor operation.

• Supplies continuous phase shift to maintain motor rotation
• Helps the motor start reliably under load
• Symptoms can include humming, slow or no start, or overheating shutdown
• Restores normal operation when the original capacitor has weakened

• Disconnect power before servicing; discharge the old capacitor safely
• Note wire locations and transfer leads to the new capacitor one-by-one
• Mount securely in the original bracket or location to prevent vibration
• If the motor still won't start, further diagnosis of the motor or start device may be required

Restore worn dishwasher racks and help prevent rust stains on dishes. This white rack repair kit covers chipped or exposed rack tines and caps bare metal to reduce corrosion and extend the useful life of your racks.

• Re-coats rusted or chipped vinyl on rack tines to help stop corrosion
• Caps exposed tips to reduce rust transfer, scratching, and snags
• Useful when tine caps are missing or the rack coating is flaking
• Common symptoms: rust on tines, stained dishes, sharp/rough tine ends

• Disconnect power and remove the rack before repair
• Clean and dry affected areas thoroughly before applying coating
• Apply in a well-ventilated area; allow full cure time before using the dishwasher
• Replace the rack if metal is severely corroded or broken

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

This machine screw secures panels, brackets, and other components inside your appliance. Replacing a missing or damaged fastener restores a solid fit, reduces vibration and rattling, and helps keep assemblies properly aligned for reliable performance.

• 10-32 machine-thread fastener for mounting and securing internal parts and panels
• Helps maintain alignment and structural integrity of assembled components
• Replaces missing, stripped, or damaged hardware
• Reduces rattling, vibration, or loosening from worn fasteners

• Disconnect power; shut off gas or water supplies before servicing
• Match thread and length to the original fastener used in that location
• Start by hand to avoid cross-threading; tighten snugly without overtightening
• Reuse original washers or clips if present and in good condition