Kudso1fl556 Parts

This push-in screw cover conceals exposed fasteners or open screw holes on your appliance for a clean, finished look. It snaps into place to hide hardware and help keep dust and splashes out of the opening.

• Conceals visible screw heads or open screw holes on panels, doors, or trim
• Helps block dust and moisture from entering the opening
• Restores appearance when the original cap is missing or damaged
• Common symptoms: missing cap, cracked or loose cover, visible fastener or hole

• Align the cap with the hole and press in until fully seated and flush
• Clear any debris or old cap fragments from the hole to ensure a secure fit

This dishrack track stop fits ball-bearing style rails and prevents the rack from being pulled out too far. Replacing a worn or missing stop restores smooth rack glide and helps keep dishes secure during loading and unloading. What it does:

• Snaps into the end of the rack track to stop the rack from sliding off
• Helps maintain proper alignment and smooth movement on ball-bearing rails
• Reduces risk of the rack detaching when fully extended
• Typical symptoms: rack pulls all the way out, falls off the track, loose/rough glide, broken or missing end stop

• 1 dishrack track stop

• Disconnect power and water to the dishwasher before servicing
• Pull the rack forward, remove the old stop from the track end, and snap the new stop into place
• Make sure it fully engages the track and the rack glides and stops correctly
• If your model uses two stops, repeat on the other rail as needed

Color: Stainless

Right-side basket lid for top-load washers. Replaces a cracked or damaged right-side lid to help contain laundry, reduce splashing and restore the basket cover so the washer closes and operates as intended. What it does:

• Covers the right side of the inner wash basket and helps keep clothes from catching on the basket edge.
• Helps reduce water splash and keeps items contained during the wash.
• Restores proper fit and alignment of the basket cover area that may affect lid closing.
• Used when the original right-side lid is cracked, warped, or broken.

• Disconnect power and water supply before beginning service.
• Handle edges carefully; wear gloves to avoid sharp edges on broken parts.
• Installation typically requires removing the outer cabinet or basket access panels and securing the lid with existing fasteners — follow the model's service manual for exact steps.

This replacement left-side lid for the silverware basket restores coverage and helps keep utensils contained during dishwasher cycles. It matches OEM fit and appearance so the basket functions as designed. What it does:

• Covers and secures utensils in the left section of the silverware basket
• Helps prevent small items from shifting or falling through during wash cycles
• Restores proper basket alignment for even water flow and rinsing
• Reduces the chance of utensil contact with rotating spray arms

• Snap-in replacement; no special tools typically required
• Remove the silverware basket to access and align the lid before snapping into place
• Inspect surrounding basket clips/rims for damage and replace if worn to ensure secure fit
• Disconnect power to the appliance and follow the manufacturer's safety instructions before servicing

Color: Black

This pump sump screen filters lint, debris and small objects from wash water before it reaches the drain pump, helping prevent clogs and pump damage. Replace a cracked or clogged screen to restore proper draining. What it does:

• Captures lint, coins, hair and small debris before the drain pump
• Helps prevent pump blockages that cause poor draining or standing water
• Reduces wear on the drain pump by stopping larger debris
• Improves overall drain performance when the existing screen is damaged or clogged

• Disconnect power and water before accessing the pump area
• Remove the washer access panel or cabinet per your model's service instructions to reach the sump
• Inspect and clean surrounding areas and the pump inlet when replacing the screen

A small replacement retainer that secures the FlexRow assembly so the component stays aligned and stable during use. Replacing a worn or broken retainer restores proper positioning and reduces movement. What it does:

• Holds the FlexRow assembly in place to prevent shifting or sagging
• Helps maintain correct alignment for even operation
• Stops clicking, rubbing, or intermittent contact caused by a loose assembly
• Prevents additional wear on adjacent clips or mounts

• Disconnect power to the appliance before beginning any repair
• Removal usually requires releasing adjacent clips or fasteners; basic hand tools may be needed
• Inspect surrounding parts and replace any damaged clips or mounts for a secure fit

This dual positioner assembly helps align and hold the control shaft/knob mechanism so selections register correctly and controls operate smoothly. It replaces a worn or broken positioner to restore reliable selector alignment. What it does:

• Secures and centers the control shaft/knob so detents register properly
• Prevents loose or wandering knobs and helps ensure accurate cycle selection
• Commonly replaced when knobs feel sloppy, skip positions, or controls don't stay set
• Works with the control panel mounting to stabilize selector movement

• Disconnect power to the appliance before starting any work
• Remove the control panel or console to access the positioner per your model's service instructions
• Handle plastic tabs and mounting points carefully to avoid breakage during removal/installation
• Test control function after reassembly to confirm correct alignment and operation

This splash guard seal fits along the dishwasher door to help keep water inside the tub and reduce leaks and drips during cycles. It restores a tighter door seal for more reliable washing performance. What it does:

• Replaces the worn or cracked splash guard seal that lets water escape around the door
• Helps prevent puddles and water on the floor after wash cycles
• Reduces visible leaks and dripping from the bottom/front of the dishwasher door
• Restores the intended door-to-tub barrier to improve containment during operation

• One splash guard seal as shown

• Inspect the door and mounting channel for debris before installing; clean surfaces for a proper fit
• Install by seating the seal into the door/tub channel; no special tools typically required
• If the old seal is brittle or stuck, use gentle prying to remove—avoid sharp tools that can damage surrounding parts
• Disconnect power and water to the appliance before performing repairs; follow all safety guidelines

This inlet water bezel is the trim piece that fits around the washer's water inlet to provide a finished opening and support the inlet connection. It restores appearance and helps position the inlet area for a proper hose fit. What it does:

• Covers and finishes the water inlet opening on the cabinet for a clean appearance
• Helps hold and align the inlet connection and hose to reduce stress on the valve
• Prevents direct contact between the inlet hose/valve and the cabinet edge
• Commonly replaced when the inlet trim is cracked, broken, or worn

• Disconnect power and shut off the water supply before starting
• Remove the appropriate access panel or control console to reach the inlet area
• Handle the bezel carefully to avoid scratching painted surfaces during install
• Re-check inlet hose routing and tighten connections; test for leaks after restoring power/water

This console assembly replaces the external control panel and button interface so you can restore user controls and display feedback on your appliance. It provides the finished bezel, buttons, and underlying electronics as a single service-ready piece. What it does

• Replaces a damaged, cracked, or cosmetically worn control console so buttons and labels are legible and accessible
• Restores unresponsive or intermittent button presses when underlying key switches or board are faulty
• Replaces a console with missing or faded markings that make cycle selection difficult
• Helps resolve display backlight or indicator issues when caused by the console assembly

• One console assembly (control panel) as shown

• Disconnect power to the appliance before beginning service to avoid electrical shock
• Typical replacement requires removing the access panel or console trim and unplugging wiring connectors; handle the display and lenses carefully to avoid scratching
• Transfer any needed brackets, overlays, or mounting clips from the old console if they are not pre-attached

Color: Biscuit. Screw for lower toe panel. For black screw use WP302868, for white screw use WP3400836.

Color: White. Size: 1 qt. can. Acrylic appliance paint.