Kuiix305ess Parts

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

This screw grommet anchors a screw in thin appliance panels so trim, covers, or consoles stay tight. It provides a snug, vibration-damping fit where a standard screw could loosen or strip over time.

• Creates a captive insert so a screw can securely fasten to sheet metal or plastic panels
• Replaces a worn, cracked, or missing grommet to restore proper screw retention
• Helps reduce panel rattles and movement from vibration
• Typical signs of failure: screw won't tighten, panel or trim feels loose, grommet falls out

• Disconnect power and shut off gas/water as applicable before servicing
• Remove the screw and lift out the old grommet; clear debris from the opening
• Press the new grommet straight into the hole until fully seated and flush
• Reinstall the screw and tighten gently to avoid deforming the grommet

Connects the cutter grid to your ice maker's electrical system. Replace if wires are frayed, damaged, or connections are loose or corroded.

Touch-up paint for appliances. Covers chips, scratches, and worn areas on range tops, refrigerators, and other appliances. Includes brush applicator.

Flip-down door won't stay closed or open smoothly? This push latch secures compartment doors with a spring-action catch. Simple DIY fix in minutes.

Ice machine not making ice or compressor not starting? This electronic control board manages freezing cycles and water pump operation. Moderate repair.

Fix an ice maker that won't start, is unresponsive, or stops making ice too early. This control board restores proper operation in about 15 minutes.

The Reservoir Drain Tube is an OEM part for Whirlpool freestanding icemakers. It is responsible for draining melted water from the reservoir during the harvest cycle. This tube removes water to allow for new ice formation. 

Causes of a bad reservoir drain tube can include mineral buildup or blockages within the tube inhibiting proper drainage over time. Additional causes may be cracks, cracks, kinks, or other damage limiting water flow.

Symptoms of a bad reservoir drain tube include:

• Water not draining from the reservoir after harvest
• Excess water collecting in the reservoir 
• Slow or reduced ice production due to poor drainage
• Leaks or water spills around the drain tube area

This OEM Whirlpool replacement tube is also compatible with freestanding ice components manufactured by select Kenmore models. 

Replacement screw that secures panels, brackets, and trim to appliance cabinets. Restores reliable hold when original hardware is stripped or missing.

Size: 8 x 1-1/4 inch.

Ice maker not producing ice or evaporator pan bulging? This evaporator requires HVAC certification, vacuum pump, gauges, and refrigerant skills.

If your ice maker pump won't run or stops draining, damaged wiring may be the cause. This pump wire harness restores electrical connection. DIY-friendly.

Size: 8-18 x 1/2 inch.

The Nut is an OEM replacement part for Whirlpool refrigerators. This small yet essential component is used to secure various parts of the refrigerator, such as shelves, panels, or brackets, ensuring stability and proper alignment. Its durable design ensures reliable performance in the demanding environment of a refrigerator.

Causes of a bad or missing Nut can include wear over time, accidental stripping of threads, or loss during maintenance or repairs. A damaged or missing nut can lead to loose components and reduced functionality.

Symptoms of a bad or missing Nut include:

• Loose or wobbly shelves, brackets, or panels
• Difficulty keeping refrigerator components securely in place
• Rattling or unusual noises during operation

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Leaking or damaged tube in your ice maker? This replacement tube restores secure connections between components to prevent leaks and ensure proper flow.

Fix ice maker clicking or not cooling issues with this compressor start relay. Restores normal compressor starts. Moderate DIY repair in under an hour.