Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix water leaking onto the floor or uneven tub filling with this upper water injector. Directs inlet water cleanly into the tub. Easy DIY replacement.
An easy fix for the most part. I had no idea what I was doing, but glad I bought both upper and lower injectors. Not sure why these are separate parts? Cheap plastic. I did not get the hose clamp because I didn't think I would need it. You probably do, so go ahead and just order it or grab one if you have one laying around. Mine is hooked up without it for now which I'm sure I will regret later but I needed to get our washer running immediately due to a bed bug situation in our house. Read more
Water was not draining on spin cycle. Opened front cover and found belt laying on the floor. After further inspection found motor pulley wheel broken. Ordered pulley and belt kit. Replaced pulley along with pump belt and tub belt. Washer is working again. Read more
This spring-timer knob replaces a worn, cracked or missing timer knob so you can set and adjust the appliance's mechanical timer reliably. Simple, direct replacement that restores the user control interface. What it does:
Removed shaft with slide hammer and inspected the yoke and gearing replaced the shaft and seals with the shaft kit and replaced the tub bearing. 32 years and still running strong Maytag yeah!!!! Doubt the newer ones will run as long thanks for having the parts. Read more
Clamp Includes 205529 Bolt Kit. It Does *not* include The The Rubber Seal. If Seal Required, Use WP211232
I removed the front cover and saw water a rusted out drum cover clamp. Water gushed out at this point when i operated the machine. I ordered a new clamp and seal from Appliance Parts Pros, which arrived quickly. I wire-brushed the drum and it's cover clean, in the sealing area and installed the new seal and clamp. NOTE do not set the cover down all the way down, or the tub will not "spin". Leave 3/8- 1/2" clearance between the top of the tub and the upper cover. I chose to fix my old... Read more
This replacement cap fits over a range/oven control knob to restore finished appearance and protect the underlying shaft. It snaps into place and matches original white knobs for a cohesive control panel look. What it does:
This genuine OEM part is a washer motor. The washer motor is the main engine that drives the washer tub allowing it to rotate and wash clothes effectively. After continuous use, a washer motor can become inoperable. If the washer is no longer spinning or the power has significantly decreased, it might be a sign that the motor needs to be replaced. To replace the motor, start by unplugging the washer. Once unplugged, move the washer away from the wall to gain access to the back panel. Uninstall the back panel by removing the screws that attach it. After removal, locate the drive motor and proceed to unthread the mounting bolts holding it to the washer. Proceed to pull the old motor out of its place. Make sure to detach the wire harness and any individual wires on the motor. Reinsert the wires into their correct terminals and install the new motor by threading the bolts that secure it. This replacement part is sold individually and is sourced directly from the manufacturer. It is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, Sears, and Kenmore brand washers.
The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more
I took the cover off the transmission and determined that the only possible knocking had to be coming from the yoke. I ordered a new yoke and all the tub seals needed to put it back together like new. I also ordered a new drive pulley bearing because this bearing is always turning whenever the washer is used. I cleaned all the parts up while I was waiting for the new parts to arrive. I promised my wife I would make it look like new. I installed all the new parts in one day and let the... Read more
Screw kit for front panel.
The lid shut-off switch is located behind the lid How About That. I order the plastic ball the hold the lid in place plus the lid shut off switch. I watched the video that AppliancePartsPros.com has on how to replace the lid and the plastic balls. I removed the lid to get to the two philips head screws to remove that part of the shut-off switch. I took the new switch out of the package and compared it to the old switch. I assembled the switch just like the old switch look using the new... Read more