Lde9608acm Parts

This 6-foot dryer vent duct connects your dryer's exhaust outlet to the wall vent. It provides a secure path for moist air to exit the home, helping maintain airflow and consistent drying performance. What it does:

• Vents hot, moist air from the dryer to the exterior
• Replaces crushed, torn, or lint-clogged ducting
• Helps address longer dry times, heat buildup/shut-offs, or moisture and lint around the dryer
• Supports a short, direct run to reduce kinks and airflow restrictions

• One 6-foot dryer vent duct

• Disconnect power; for gas models, turn off the gas supply before starting
• Pull the dryer forward and remove old ducting and lint/debris from connections
• Attach the duct fully to the dryer outlet and wall vent and secure with clamps; avoid sharp bends or crushing
• Move the dryer back carefully and confirm strong airflow at the exterior vent hood

This motor clip secures a motor to its mounting bracket or housing, keeping it aligned and stable during operation. Replacing a bent, broken, or missing clip helps stop rattling and prevents the motor from shifting. What it does:

• Retains the motor on its mounting bracket or frame
• Helps maintain alignment to reduce vibration and noise
• Prevents movement that can cause rubbing or wire strain
• Direct replacement when the original clip is damaged or missing

• One motor clip

• Disconnect power before servicing; allow all moving parts to stop
• Access the motor area, note the clip's orientation, and remove the damaged clip
• Seat the motor fully, then install the new clip to secure it to the bracket
• Inspect related mounts/grommets and wiring for wear; verify clearances before restoring power

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

This drum baffle mounts inside the rotating drum to lift and tumble laundry during each cycle. Replacing a cracked, loose, or missing fin helps prevent snags and restores proper load movement. What it does:

• Lifts and turns items as the drum rotates to improve tumbling
• Separates garments to reduce tangling and keep loads moving evenly
• Helps prevent small items from lying flat against the drum surface
• Common symptoms include rattling or thumping, visible cracks, clothes snagging/tearing, and reduced tumbling

• One tall drum baffle

• Disconnect power; shut off gas supply before servicing
• Wear cut-resistant gloves; interior cabinet edges can be sharp
• Rotate the drum to access mounting points; support the drum while removing/installing the baffle
• Tighten fasteners securely; hand-turn the drum to verify clearance before testing

Size: 10-32 inch.

The Dryer Timer Dial Skirt is an OEM part designed specifically for Whirlpool dryers. It acts as a protective and decorative cover around the timer dial, providing clear labeling for various dryer settings. 

Color: Bisque

Over time, the dial skirt may degrade due to frequent use, exposure to heat, and potential impact, leading to cracks, discoloration, or broken markings. These issues can make selecting the appropriate cycle difficult or confusing.

Signs that the Dryer Timer Dial Skirt may need replacing include:

• Faded or illegible cycle markings
• Cracks or broken sections on the skirt
• The dial skirt no longer fitting snugly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Screw: 8-16 x 3/8 inch.

Specs: No.8X1/2 HEX WASHER HEAD

Color: White. For black order WP98008545. For biscuit order 98008169.

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.

This ground screw secures the appliance grounding conductor to the chassis for a reliable electrical ground connection, helping maintain safety and proper operation. It's a direct-fit fastener used where a dedicated ground screw is required. What it does

• Fastens the grounding conductor to the appliance frame to maintain a secure earth/ground connection.
• Helps prevent electrical shock and reduces risk of stray voltage on the chassis.
• Addresses symptoms like intermittent or absent grounding and loose or corroded ground connections.
• Used wherever the original equipment grounding screw has been lost, damaged, or corroded.

• Disconnect power at the breaker and unplug the appliance before starting any work.
• Only attach to designated grounding points on the chassis; ensure the mating surface is clean and free of paint or corrosion.
• Use the correct driver and moderate hand torque—do not overtighten to avoid stripping threads.

This door strike is the replacement latch striker that the door latch catches on to secure the appliance door. Restores proper door engagement and helps the door close and seal correctly. What it does

• Provides the matching contact point for the door latch so the door stays closed
• Commonly replaces worn or broken strikes that cause the door to not latch or to pop open
• Can resolve noisy closing, misalignment, or intermittent latching issues
• Works with the OEM latch assembly to maintain proper door alignment and sealing

• One door strike

• Disconnect power (or unplug) before starting any repair
• Remove exterior panels or trim as needed to access the strike; keep all fasteners
• Align the strike so the latch engages smoothly — do not force components

A replacement 3/8-16 nut that secures fasteners and assemblies on compatible Whirlpool appliances. Restores proper fastening so panels, brackets and components stay tight and aligned during normal operation. What it does:

• Fastens and secures bolts, studs or threaded shafts in appliance assemblies.
• Prevents loose connections that can cause rattling, vibration or misalignment.
• Used where a 3/8-16 threaded nut is required for structural or mounting applications.
• Replaces missing, stripped or corroded nuts to restore reliable mechanical connection.

• Disconnect power and follow all appliance safety procedures before servicing.
• Inspect mating threads and remove debris; replace if threads are damaged.
• Thread onto bolt or stud by hand first, then snug with the correct wrench; avoid overtightening.
• Follow the appliance manufacturer's torque and assembly instructions.

This is a genuine replacement mounting screw used to secure appliance components and panels. It restores proper fit and prevents movement that can cause noise or misalignment. What it does:

• Fastens panels, brackets, and small components in place
• Helps stop rattling or vibration caused by loose hardware
• Restores secure attachment after stripped or missing fasteners
• Matches OEM thread and head style for correct fit

• Use the correct driver to avoid stripping the head
• Tighten until snug; do not overtighten to prevent damage
• Disconnect power to the appliance before accessing internal components
• Replace matching screws in the area for consistent fit

This replacement screw fastens appliance panels, brackets, and components. Use it to replace missing, stripped, or rusted hardware to restore a secure fit and help reduce vibration or rattling during operation.

• Secures panels, brackets, and internal components to the cabinet or frame
• Helps prevent vibration, rattling, and misalignment from loose hardware
• Replaces a missing, rusted, or stripped original screw
• Matches the original fastener style for proper fit in specified locations

• Disconnect power; shut off gas and water supplies before servicing
• Use the correct screwdriver or nut driver and match length/thread to the original
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic or thin metal