Le4127w2 Parts

This is a small rubber or plastic cup that sits beneath a washer's leveling leg to protect the floor and reduce vibration. It helps keep the machine stable and prevents the legs from scratching or damaging the surface underneath. Replace this pad if it is cracked, compressed, or missing, which can cause the washer to vibrate excessively, walk across the floor, or make loud banging noises during the spin cycle.

This 240-volt heater assembly restores the appliance's ability to generate and maintain heat during operation, helping cycles reach designed temperatures for proper performance and results. What it does:

• Converts electrical energy into heat for the appliance's heating circuit
• Helps the unit reach and hold target temperatures during heat-required portions of the cycle
• Replaces a damaged, shorted, or open heating element
• Symptoms can include no heat when expected, longer-than-normal cycles, tripped breakers, or heater-related error codes

• 1 heater assembly

• Disconnect power at the breaker before servicing; 240V circuits can be hazardous
• Document wire locations and move connectors one at a time to the new assembly
• Avoid bending or striking the element; ensure secure mounting and proper clearances
• After installation, check related safety devices (high-limit, thermostats, fuses) and verify the circuit has correct voltage and continuity

Factory protective shield panel for dryer assembly. Guards internal components and directs heat or airflow. Replace if cracked, broken, or missing.

This retainer clip secures a component in place to prevent movement and maintain proper alignment during appliance operation. Replacing a damaged or missing clip helps restore safe, reliable performance.

• Holds the mating part firmly to reduce vibration and noise
• Helps prevent intermittent operation caused by loose fitment
• Common fix when a component feels loose, rattles, or won't stay seated

• Disconnect power and shut off gas/water before servicing
• Note original clip orientation and location before removal
• Use needle-nose pliers to carefully release and install the clip
• Do not over-bend the clip; replace if deformed or fatigued

Dryer stopped heating or takes hours to dry? This heating element restores proper heat output. Typical repair takes about an hour with basic tools.

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses airflow through the heat-exchange coils for proper operation
• Supports and aligns the blower wheel so it spins with correct clearance
• Helps minimize vibration and noise when the housing is intact
• Symptoms of a failed housing may include scraping or rattling noises, weak airflow, vibration, or visible cracks/broken mounts around the blower area

• Disconnect power before servicing; wear cut-resistant gloves and eye protection.
• Remove the front panel/cabinet to access the blower section; note screw and clip locations.
• Transfer the blower wheel, seals, and any reusable hardware from the old housing.
• Before reassembly, spin the blower wheel by hand to ensure free, rub-free rotation.

This is a heat shield insulator that mounts on the inner side of the dryer door in a stacked laundry center or washer/dryer combo unit. It prevents excessive heat from transferring through the door during drying cycles, protecting the outer door surface and improving energy efficiency. Replace this insulation if it is torn, deteriorated, or missing, which can cause the door to become excessively hot to the touch or reduce drying performance.

This is a small C-clip or retainer ring that secures the idler pulley to its bracket on a laundry center. It keeps the pulley in place so the drive belt maintains proper tension against the drum. Replace this ring if the idler pulley has come loose, the drum belt slips or falls off, or the dryer drum does not spin properly.

Shaft that the idler pulley rotates on in your dryer. Replace if worn, wobbling, or causing squealing. Helps maintain proper belt tension and alignment.

A replacement bracket glide that secures and guides an appliance drawer or shelf glide so drawers open and close smoothly. Installing a new bracket restores proper alignment and helps prevent sticking, sagging and noisy operation. What it does:

• Supports and guides the drawer/glide assembly for smooth, even movement.
• Keeps the drawer aligned so it does not bind, tip or come off the track.
• Reduces scraping, grinding or rattling noises caused by a damaged bracket.
• Common symptom: drawers that stick, sag, pull to one side, or feel loose.

• Disconnect power (or unplug) and empty the drawer before you start.
• Remove the drawer or access panel to reach the bracket; basic hand tools are usually required.
• Retain original fasteners unless the replacement explicitly includes new hardware.

Rubber bumper cushions washer lid closure. Installs between lid and cabinet to absorb impact and reduce noise. Replace if worn, cracked, or missing.

Replacement machine bolt for securing panels, brackets, and components in dishwashers, dryers, washers, and laundry centers. Restores fit if missing.

Secures refrigerator grille or trim to cabinet, preventing rattles and gaps. Replace when broken or missing to restore proper panel alignment. Verify fit with your model number before ordering.

This white front door panel replaces a damaged or worn exterior door and restores the appliance's appearance and sealing surface. It matches the original panel shape and finish for a factory look. What it does

• Replaces a cracked, dented, chipped or otherwise damaged front door panel
• Restores the appliance's exterior finish and helps maintain proper door alignment
• Provides the factory surface for attaching original trim, hinges and handles
• Improves appearance after impact or long-term wear

• One white front door panel

• Disconnect power and water before beginning work
• Some trim, handles or hinges may need to be transferred from the old door; inspect fasteners and hardware
• Handle panels carefully to avoid scratching the finish during installation
• Tighten fasteners to manufacturer torque specs and check door alignment after installation